Benutzeranleitung / Produktwartung H35-LP1 des Produzenten Hampton Direct
Zur Seite of 48
FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD. 6988 V enture St., Delta, BC Canada, V4G 1H4 W ARNING: If the information in these instructions are not followed ex- actly , a fi re or explosion may result causing property damage, personal injury or loss of life.
2 Hampton ® H35 Direct V ent Freestanding Gas Stove HAMPT ON ® Direct V ent Freestanding Gas Stove UNIT DIMENSIONS T o the New Owner: Congratulations! Y ou are the owner of a state-of-the-art Hampton ® Gas Stove by FPI FIREPLACE PRODUCTS INTERNA TIONAL L TD.
Hampton ® H35 Direct V ent Freestanding Gas Stove 3 T ABLE OF CONTENTS Conversion Kit to Lower BTU Rating ........................... 31 Brick Panel .................................................................. 32 Log Set Installation ..........
4 Hampton ® H35 Direct V ent Freestanding Gas Stove This is a copy of the label that accompanies each Direct V ent Freestanding Gas Stove. We have printed a copy of the contents here for your review . SAFETY LABEL NOTE: Hampton ® units are constantly being improved.
Hampton ® H35 Direct V ent Freestanding Gas Stove 5 REQUIREMENTS 5.08: Modifica tions to NFPA-54, Chap ter 10 (2) Revise 10.8. 3 by adding the following a dditional requi rements: (a) For all side wa.
6 Hampton ® H35 Direct V ent Freestanding Gas Stove IMPORT ANT MESSAGE SA VE THESE INSTRUCTIONS The Direct V ent Freestanding Gas Stove must be installed in accordance with these instructions. Carefully read all the instructions in this manual fi rst.
Hampton ® H35 Direct V ent Freestanding Gas Stove 7 INST ALLA TION manufactured home the unit must be bolted down to the fl oor . 4) This appliance is Listed for bedroom instal- lations when used with a Listed Millivolt Thermostat. Some areas may have further requirements, check local codes before installation.
8 Hampton ® H35 Direct V ent Freestanding Gas Stove OPTIONAL F AN INST ALLA TION Diagram 1 Diagram 2 LOCA TING YOUR GAS ST OVE When selecting a location for your stove, ensure that the clearances listed above are met as well as ensuring that there is adequate accessibility for servicing and proper operation.
Hampton ® H35 Direct V ent Freestanding Gas Stove 9 INST ALLA TION INST ALLA TION PRECAUTIONS These venting systems are engineered products that have been designed and tested for use with the H35-NG1, and H35-LP1.
10 Hampton ® H35 Direct V ent Freestanding Gas Stove EXTERIOR VENT TERMINAL LOCA TIONS A= Clearance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm) B= Clearance to window or door that may be opened *(12"/30cm) C= Clearance to permanently closed window *(min.
Hampton ® H35 Direct V ent Freestanding Gas Stove 11 INST ALLA TION FPI 946-506/P V ent Guard (Optional) 640-530/P Riser V ent T erminal 946-205 Vinyl Siding Shield for Riser V ent T erminal 946-208/.
12 Hampton ® H35 Direct V ent Freestanding Gas Stove RIGID PIPE VENTING SYSTEMS Horizontal or V ertical T erminations Alternate Horizontal T ermination Caps INST ALLA TION Pipe Length V ertical T ermination Cap S torm Collar Flashing Ceiling Firestop 24" Pipe Length Adj.
Hampton ® H35 Direct V ent Freestanding Gas Stove 13 INST ALLA TION Offset to V ertical T erminations VENTING ARRANGEMENTS V ertical T erminations Systems for Residential Manufactured and Mobile Homes The shaded area in the diagram below shows all allowable combinations of straight vertical and offset to vertical runs with vertical terminations.
14 Hampton ® H35 Direct V ent Freestanding Gas Stove VENTING ARRANGEMENTS HORIZONT AL TERMINA TIONS USING RIGID PIPE Dura-V ent Snorkel T ermination Riser V ent T ermination The two diagrams show all allowable com- binations of straight horizontal termination using Rigid Pipe.
Hampton ® H35 Direct V ent Freestanding Gas Stove 15 Horizontal V enting with T wo (2) 90 o Elbows Option V H + H1 A) 3' Min. 2' Max. B) 4' Min. 3' Max. C) 5' Min. 4' Max. D) 6' Min. 5' Max. E) 7' Min. 6' Max.
16 Hampton ® H35 Direct V ent Freestanding Gas Stove H1 H V V ertical V enting with T wo (2) 90 o Elbows Option V H V + V1 A) 1' Min. 3' Max. 2' Min. B) 2' Min. 4' Max. 3' Min. C) 3' Min. 5' Max. 4' Min. D) 4' Min.
Hampton ® H35 Direct V ent Freestanding Gas Stove 17 V enting Arrangements - V ertical T erminations with Co-linear Flex System for both Residential & Manufactured Homes into Masonry Fireplaces The shaded area in the diagram shows the allowable vertical terminations.
18 Hampton ® H35 Direct V ent Freestanding Gas Stove Review the following sequence of instructions which are typical of most installations. The se- quence may vary depending on wall thickness.
Hampton ® H35 Direct V ent Freestanding Gas Stove 19 INST ALLA TION Note: T h e pipe seam should be facing down. Note: T o make the installation more aes- thetically pleasing, we recommend framing out a square that the cap can be mounted on.
20 Hampton ® H35 Direct V ent Freestanding Gas Stove Alternate Horizontal T ermination Caps Dura-V ent Basic Horizontal Kit # 970 1 90 o Elbow 1 W all Thimble Cover 1 Horiz.
Hampton ® H35 Direct V ent Freestanding Gas Stove 21 Diagram 2a Diagram 3 Below Grade Snorkel Installation If the Snorkel T ermination must be installed below grade, i.e. basement application, proper drainage must be provided to prevent water from entering the Snorkel T ermination.
22 Hampton ® H35 Direct V ent Freestanding Gas Stove Diagram 7 Diagram 6 Diagram 5 Diagram 4 b) The location of the horizontal vent termi- nation on an exterior wall must meet all local and national building codes, and must not be blocked or obstructed.
Hampton ® H35 Direct V ent Freestanding Gas Stove 23 Roof Pitch Minimum V ent Height Feet Meters fl at to 7/12 2 0.61 over 7/12 to 8/12 2 0.61 over 8/12 to 9/12 2 0.61 over 9/12 to 10/12 2.5 0.76 over 10/12 to 1 1/12 3.25 0.99 over 1 1/12 to 12/12 4 1.
24 Hampton ® H35 Direct V ent Freestanding Gas Stove CONVERTING CLASS-A MET AL CHIMNEY OR MASONR Y CHIMNEY T O DIRECT VENT SYSTEM There are two different types of direct vent conversion systems listed below . Follow the appropriate directions for your installation.
Hampton ® H35 Direct V ent Freestanding Gas Stove 25 4) Assemble the desired lengths of Black Pipe and Elbows necessary to reach from the appliance adapter up through the support box and fl ashing to proper height as per Diagram 12, local codes or the "Exterior V ent T erminal Locations" section.
26 Hampton ® H35 Direct V ent Freestanding Gas Stove GAS PIPE PRESSURE TESTING The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig.
Hampton ® H35 Direct V ent Freestanding Gas Stove 27 INST ALLA TION THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! Each Kit contains one LPG Conversion Kit and one DC Sparker Kit. LPG Conversion Kit Contains: Qty .
28 Hampton ® H35 Direct V ent Freestanding Gas Stove 17) Reverse steps 4) to 2). 18) Attach clear label "This unit has been converted to LPG" near or on top of the serial # decal. 19) Replace yellow "Natural Gas" label with red "LPG" label.
Hampton ® H35 Direct V ent Freestanding Gas Stove 29 9) Install the plastic bushing over the outside of the hole. 10) Attach the ground wire to the DC spark mounting bracket. 11 ) Attach the DC sparker generator wires to the DC sparker . 8) Insert both the ground wire and the DC sparker generator wire through the hole of the DC spark heat shield.
30 Hampton ® H35 Direct V ent Freestanding Gas Stove 5) Connect the DC spark generator wires to the SIT V alve with the screw , which is provided in the kit. 6) Locate the ground lug at the receptical box, left of the unit. Installer Notice: These instructions must be left with the appliance.
Hampton ® H35 Direct V ent Freestanding Gas Stove 31 CONVERSION KIT T O LOWER BTU RA TING NA TURAL GAS - KIT #: 740-950 PROP ANE - KIT # 740-952 THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! Natural Gas Conversion Kit 740-950 Contains: Qty .
32 Hampton ® H35 Direct V ent Freestanding Gas Stove LOG SET INST ALLA TION Read the instructions below carefully and refer to the diagrams. If logs are broken do not use the unit until they are replaced. Broken logs can interfere with the pilot operation.
Hampton ® H35 Direct V ent Freestanding Gas Stove 33 C)02-44 Pins on Rear Log Support A)02-43 B)02-56 4) Place Rear Log A)02-43 on the two pins on the rear log support. 5) Place the Middle Left Log B)02-56 on the two pins as shown. 6) Sprinkle some lava rock just in front of B) 02-56 on the burner holes.
34 Hampton ® H35 Direct V ent Freestanding Gas Stove INST ALLA TION DOUBLE DOOR INST ALLA TION 1) Secure the T op Door Clip into the T op Front Casting.
Hampton ® H35 Direct V ent Freestanding Gas Stove 35 INST ALLA TION DOOR HINGE REMOV AL 1) Remove the cast top by lifting it off of the stove. 2) Release the catches on the left and right side of the stove that secure the glass. 3) Remove the glass by sliding it up and out.
36 Hampton ® H35 Direct V ent Freestanding Gas Stove WIRING DIAGRAMS CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. If any of the original wires as supplied with the appliance must be replaced, it must be replaced with CSA type SEW (200 o C) or its equivalent.
Hampton ® H35 Direct V ent Freestanding Gas Stove 37 REMOTE CONTROL Use the Hampton ® Remote Control Kit approved for this unit. Use of other systems may void your warranty . The remote control kit comes with a hand held transmitter , a receiver and a wall mounting plate.
38 Hampton ® H35 Direct V ent Freestanding Gas Stove OPERA TING INSTRUCTIONS OPERA TING INSTRUCTIONS 1) Read and understand these instructions before operating this appliance. 2) Check to see that all wiring is correct and enclosed to prevent possible shock.
Hampton ® H35 Direct V ent Freestanding Gas Stove 39 COPY OF THE LIGHTING PLA TE INSTRUCTIONS OPERA TING INSTRUCTIONS AUT OMA TIC CONVECTION F AN OPERA TION The fan operates automatically - turn the knob at the top right rear corner to adjust to the desired speed.
40 Hampton ® H35 Direct V ent Freestanding Gas Stove MAINTENANCE T op View of pilot fl ame MAINTENANCE INSTRUCTIONS 1) Always turn off the valve before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year .
Hampton ® H35 Direct V ent Freestanding Gas Stove 41 T o remove fan: 1) Unplug or disconnect power source to stove. 2) Remove the 6 screws holding the access panel in place. F AN MAINTENANCE If your fan requires maintenance or replace- ment, access to the fan is through the rear access panel on the back of the unit.
42 Hampton ® H35 Direct V ent Freestanding Gas Stove 11 ) Carefully lift the burner tray assembly out. REMOVING V AL VE If your valve requires maintenance or replace- ment, use the following instructions: Note: Al ways close off the gas supply before removing the valve.
Hampton ® H35 Direct V ent Freestanding Gas Stove 43 P ARTS LIST MAIN ASSEMBL Y 1) 942-301** Casting - T op 2) 942-31 1** Casting - T op Grill 3) 942-321** Casting - Left Side 4) 942-331** Casting - .
44 Hampton ® H35 Direct V ent Freestanding Gas Stove BURNER & LOG ASSEMBL Y 740-574/P V alve Assembly S.I.T . - Natural Gas 740-576/P V alve Assembly S.
Hampton ® H35 Direct V ent Freestanding Gas Stove 45 NOTES.
46 Hampton ® H35 Direct V ent Freestanding Gas Stove NOTES.
Hampton ® H35 Direct V ent Freestanding Gas Stove 47 W ARRANTY Hampton ® Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam carefully inspects each unit thoroughly before it leaves our facility .
Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Insta.
Ein wichtiger Punkt beim Kauf des Geräts Hampton Direct H35-LP1 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Hampton Direct H35-LP1 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Hampton Direct H35-LP1 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Hampton Direct H35-LP1 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Hampton Direct H35-LP1 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Hampton Direct H35-LP1 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Hampton Direct H35-LP1 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Hampton Direct H35-LP1. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Hampton Direct H35-LP1 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
