Benutzeranleitung / Produktwartung 800-EFM des Produzenten GE
Zur Seite of 44
Please read before using feature module. 800-EFM Note: The 800-EFM External Feature Module can be set as a music on hold adapter , external paging adapter , or a door intercom adapter Model 800-EFM External Feature Module User ’ s Guide 800-EFM guide for PDF v1 091102.
i Getting St arted Getting St arted Congratulations! Y ou’ve purchased a TMC Model 800-EFM External Feature Module that meets the highest st andards for quality and convenience in the Small Office/Home Of fice environment. T o get the most from your Feature Module, please take time to read this guide thoroughly .
The TMC Model 800-EFM External Feature Module is designed for easy installation in your home or office. However , it is important that you follow these few simple guidelines: - T ake a few minutes to read this manual so that you thoroughly understand the instructions to be followed for proper installation of your Feature Module .
Getting St arted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Reference Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Section 1A - Inst alling Y our External Paging Adapter .
Section 3A - Inst alling Y our Music On Hold Adapter . . . . . . . . . . . . . . 25-29 S tep 1: Connect Line Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 S tep 2: Set DIP Switches to Proper Positions . . . . . . . . . . . . . .
Reference Drawing v Strain Relief T ab Jacks for connection to W all Jacks for connection to a Phone S t atus Indicator Lamp Dip Switches Paging V olume Control Knob for External Paging Adapter AC Adapter Jack Music Input Jack for Music on Hold Adapter Music V olume Control Knob for Music on Hold Adapter 800-EFM guide for PDF v1 091102.
Inst alling Y our External Paging Adapter Section 1A Inst alling Y our External Paging Adapter 1 Page 2 S tep 1: Connect Line Cord 3 S tep 2: Set DIP Switches to Proper Positions 4 S tep 3: Connect Po.
Step 1: Connect Line Cord 1 Connect Line Cord Connect one end of a long telephone line cord to the jack on the back of the feature module labeled L1/L2. Connect the other end to a jack labeled Lines 1 & 2 or to a jack labeled line 1. PLEASE NOTE: Y ou must be sure to connect the cord to LINE 1.
Inst alling Y our External Paging Adapter Step 2: Set DIP Switches to Proper Positions Set Switches 7-8 Set switch 7 in the up position and switch 8 in the down position to set this feature module as an External Paging Adapter .
Step 3: Connect Power Cord Inst alling Y our External Paging Adapter 1 Connect Power Cord to Module Plug the AC power cord into the adapter jack at the rear of the Feature Module. Thread the power cord around the strain relief tab. 2 Connect Power Cord to W all Outlet Plug the AC adapter into an electrical outlet not controlled by a wall switch .
Step 4: Connect W iring Block to External Paging Adapter Inst alling Y our External Paging Adapter 1 Locate 8-wire Cord Find the 8-wire cord which was enclosed with your External Paging Adapter . Note that this is a black cord which is approximately 6 inches long.
Inst alling Y our External Paging Adapter Step 5: Connect Amplifier and Speaker to W iring Block 1 Inst all Amplifier and Speaker Please follow the installation instructions that came with your amplifier and speaker . Note that you may be installing a speaker with a built-in amplifier .
Inst alling Y our External Paging Adapter Step 6: Adjust Speaker V olume to Desired Level 1 Listen to Speaker V olume At the System phone nearest the External Paging Adapter , make an announcement through that external speaker (see page 10 for instructions on doing this).
9 Using Y our External Paging Adapter Section 1B Using Y our External Paging Adapter Page 10 Operation of your External Paging Adapter 1 1 Important Point s to Note 12 T roubleshooting Guide 800-EFM guide for PDF v1 091102.
10 Using Y our External Paging Adapter Operation of your External Paging Adapter T o make an announcement through a p articular external speaker: 1 Press P AGE. 2 Dial the two-digit station number of the speaker you wish to page. 3 After you hear the p aging tone, speak towards the telephone or lift the handset to make your announcement.
Import ant Point s to Note Using Y our External Paging Adapter 11 Y ou must attach your External Paging Adapter to line 1 for it to function. Y ou may connect up to 15 External Paging Adapters to your system. Connect each one to a separate External Paging speaker and assign each one a dif fer- ent station number from 12 to 26.
Using Y our External Paging Adapter T roubleshooting Guide If you are having difficulty with your External Paging Adapter , DO NOT RETURN IT! Y ou may find your problem and solution listed below . If not, call TMC’s toll-free customer support line at 1-800-TMC-1638, and an expert will walk you through your problem.
Inst alling Y our Door Intercom Adapter Page 14 S tep 1: Connect Line Cord 15 S tep 2: Set DIP Switches to Proper Positions 16 S tep 3: Connect Power Cord 17 S tep 4: Connect Wiring Block to Door Inte.
Step 1: Connect Line Cord 1 Connect Line Cord Connect one end of a long telephone line cord to the jack on the back of the feature module labeled L1/L2. Connect the other end to a jack labeled Lines 1 & 2 or to a jack labeled line 1. PLEASE NOTE: Y ou must be sure to connect the cord to LINE 1.
Inst alling Y our Door Intercom Adapter Step 2: Set DIP Switches to Proper Positions 15 Set Switches 7-8 Set switch 7 in the down position and switch 8 in the up position to set this fea- ture module as a Door Intercom Adapter .
Step 3: Connect Power Cord Inst alling Y our Door Intercom Adapter 1 Connect Power Cord to Module Plug the AC power cord into the adapter jack at the rear of the Feature Module. Thread the power cord around the strain relief tab. 2 Connect Power Cord to W all Outlet Plug the AC adapter into an electrical outlet not controlled by a wall switch .
Step 4: Connect W iring Block to Door Intercom Adapter Inst alling Y our Door Intercom Adapter 1 Locate 8-wire Cord Find the 8-wire cord which was enclosed with your Door Intercom Adapter . Note that this is a black cord which is approximately 6 inches long.
18 Inst alling Y our Door Intercom Adapter Step 5: Connect Door S peaker to Wiring Block 1 Inst all Door Speaker Please follow the installation instructions that came with your door speaker . Note that TMC Corporation does not manufac- ture door speakers.
Step 6: Connect Doorbell to W iring Block Inst alling Y our Door Intercom Adapter 1 Inst all Doorbell Please follow the installation instructions that came with your door speaker . Note that the Door Intercom Adpater supports Nutone’s lighted pushbutton.
Inst alling Y our Door Intercom Adapter Step 7: Connect Magnetic Door S trike to Wiring Block (Optional) 1 Inst all Magnetic Door Strike Please follow the installation instructions that came with your magnetic door strike. Note that TMC Corporation does not manufac- ture magnetic door strikes.
21 Using Y our Door Intercom Adapter Section 2B Using Y our Door Intercom Adapter Page 22 Operation of your Door Intercom Adapter 23 Important Point s to Note 24 T roubleshooting Guide 800-EFM guide for PDF v1 091102.
22 Using Y our Door Intercom Adapter Operation of your Door Intercom Adapter T o answer a door speaker over the intercom: 1 Press the INTERCOM button, then dial the two-digit station number of the desired door speaker . 2 T o end the conversation, hang up or press the SPEAKER button.
Import ant Point s to Note Using Y our Door Intercom Adapter 23 Y ou must attach your Door Intercom Adapter to line 1 for it to function. Y our Door Intercom Adapter is designed to be comp atible with NUTONE brand door speakers (such as model ISB-64 and model IS-69), and is also comp atible with their lighted pushbutton.
Using Y our Door Intercom Adapter T roubleshooting Guide If you are having difficulty with your Door Intercom Adapter , DO NOT RETURN IT! Y ou may find your problem and solution listed below . If not, call TMC’s toll-free customer support line at 1-800-TMC-1638, and an expert will walk you through your problem.
Inst alling Y our Music on Hold Adapter Section 3A Inst alling Y our Music on Hold Adapter Page 26 S tep 1: Connect Line Cords 27 S tep 2: Set DIP Switches to Proper Positions 28 S tep 3: Connect Power Cord 29 S tep 4: Connect Music Source 25 800-EFM guide for PDF v1 091102.
Step 1: Connect Line Cords 1 Connect First Line Cord Connect one end of a long telephone line cord to the jack on the back of the feature module labeled L1/L2.
Inst alling Y our Music on Hold Adapter Step 2: Set DIP Switches to Proper Positions 27 Set Switches 7-8 Set switch 7 in the up position and switch 8 in the up position to set this feature module as a Music on Hold Adapter . IMPORT ANT : Make sure that switch 7 is set in the up position and switch 8 is set in the up position.
Step 3: Connect Power Cord Inst alling Y our Music on Hold Adapter 1 Connect Power Cord to Module Plug the AC power cord into the adapter jack at the rear of the Feature Module. Thread the power cord around the strain relief tab. 2 Connect Power Cord to W all Outlet Plug the AC adapter into an electrical outlet not controlled by a wall switch .
Inst alling Y our Music on Hold Adapter Step 4: Connect Music Source 29 1 Connect Audio Cable to Module Plug one end of the supplied audio cable (with 1/8”plugs at each end) into the Music Input Jack on the rear of the feature module.
Using Y our Music on Hold Adapter Section 3B Using Y our Music on Hold Adapter Page 32 Providing Music to Callers on Hold 33 Providing a Recorded Message to Callers on Hold 34 Adjusting Music V olume 35 Usage Notes 36 T roubleshooting Guide 31 800-EFM guide for PDF v1 091102.
32 Using Y our Music on Hold Adapter Providing Music to Callers on Hold Y ou may use your Music on Hold adapter to provide music to callers on hold. Simply tune a radio to a favorite station and att ach it to your Music on Hold adapter . 800-EFM guide for PDF v1 091102.
Providing a Recorded Message to Callers on Hold Using Y our Music on Hold Adapter Y ou may instead choose to use your Music on Hold adapter to provide a recorded message to callers on hold. Simply record the desired message and then attach a t ape cassette player to your Music on Hold adapter .
Adjusting Music V olume 1 Listen to Music on Hold V olume At the system phone nearest the Music on Hold adapter use Line 1 to call the telephone num- ber of Line 2. When Line 2 start s ringing, place Line 1 on hold, and answer Line 2. Y ou should now be hearing the music on hold.
Y our Music on Hold Adapter must be used in a system of at least two system telephones in order for it to work. It will not work if you only have one system telephone installed. Note: Users of equipment that rebroadcasts copyrighted music or other material may be required to obtain a license from a third p arty such as ASCAP or BMI.
Using Y our Music on Hold Adapter T roubleshooting Guide If you are having difficulty with your Music on Hold Adapter , DO NOT RETURN IT! Y ou may find your problem and solution listed below . If not, call TMC’s toll-free customer support line at 1-800-TMC-1638, and an expert will walk you through your problem.
TWO-YEAR LIMITED W ARRANTY We urge you to complete the W arranty Registration Form enclosed with your product and send it in. This will enable you receive future updates and product information from TMC . What does your warranty cover? Any defect in material or workmanship.
Additional Information This equipment complies with Part 68 of the FCC rules. On the base of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence num- ber (REN) for this equipment. If requested, this information must be provided to the telephone company .
W arning: Y our feature module generates and uses R.F . (Radio Frequency) energy . It complies with FCC Part 15, Subpart J for Class B computing devices. If not used in strict accordance with manufacturer ’s instructions, the feature module can cause interference to radio and/or television reception.
TMC Corporation 2540 Route 130, Unit 1 17 Cranbury , NJ 08512 609-860-1830 T oll-free 1-800-TMC-1638 Fax 609-860-8980 www .tmccorporation.com Email: info@tmccorporation.
Ein wichtiger Punkt beim Kauf des Geräts GE 800-EFM (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie GE 800-EFM noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für GE 800-EFM - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von GE 800-EFM reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über GE 800-EFM erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon GE 800-EFM besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von GE 800-EFM verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit GE 800-EFM. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei GE 800-EFM gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
