Benutzeranleitung / Produktwartung XL4000 des Produzenten Clifford
Zur Seite of 25
World-Clas s Aut o Securit y T M.
All XL Series systems are covered by one or more of the following Clifford Electronics patents: 4,158,874; 4,233,642; 4,327,444; 4,383,242; 4,430,685; 4,845,464; 4,887,064; 4,890,108; 4,922,224; 4,997.
Table of Contents Standard Features of the XL4000 . . . . . . . . . . . . . . . . . . . 3 Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Your 4-button/12-channel remote controls . . . . . . . . . . . . . . 10 How to use your keychain remote control .
Table of Contents (cont.) How to interpret the LED status indicator . . . . . . . . . . . . . . . 16 Automatic Battery-Saving Mode . . . . . . . . . . . . . . . . . . . . . . 16 AutoLock and AutoUnLock™ . . . . . . . . . . . . . . . . . . . . . 16 Remote controlled sensor adjustments .
Standard Features of the XL4000 ✔ Lifetime Warranty —For as long as you own the vehicle, Clifford will repair or replace the control unit and remote controls free of charge (see warranty card for full details).
Standard Features of the XL4000 (cont.) ✔ Remotely Adjustable Dual-Zone Piezo Sensor™ — With just a touch on the remote, you may, at any time or place, adjust and test the sensitivity of this microprocessor-controlled solid-state sensor.
Standard Features of the XL4000 (cont.) ✔ Remote Door Locking/Unlocking with Built-in Relays — No more fumbling with keys in the dark or bad weather! A press of a button on the remote control simultaneously arms your system and locks your vehicle’s power locks.
Standard Features of the XL4000 (cont.) ✔ Multiple-Event TotalRecall™ — XL4000’s memory stores the identity of the last eight triggers and/or sensors activated. This provides an invaluable diagnostic means, since, whenever you wish, the system will visually identify the activated triggers and sensors in reverse chronological order.
Standard Features of the XL4000 (cont.) ✔ Enhanced User-Selectable AutoArming™ — Automatically arms itself “passively” if you forget. May qualify you for an insurance discount that could pay for the system (consult your insurance company).
Standard Features of the XL4000 (cont.) ✔ High-Luminescence LED Status Indicator with Automatic Battery-Saving Mode — Adds visual deterrence and identifies system status. To conserve vehicle battery power, if the system has remained continuously armed for 48 hours, the flash rate will automatically slow to half the normal rate.
Welcome to the world of high-technology vehicle security and convenience C ongratulations on the purchase of your XL4000 vehicle security/convenience system. Clifford Electronics has long been recognized as the world’s leading manufacturer of high-technology vehicle security systems and accessories.
Your 4-button/12-channel remote controls The 4-button/12-channel remote controls are ultra-sophisticated miniature radio transmitters powered by a tiny 12-volt battery. Range is up to 100 feet. A weak remote control battery will reduce range. Electrical interference and even sunspots can interrupt the signal from your remote control to the system.
What each button/channel does Your XL4000 remote controls come pre-programmed so that certain channels command certain functions. If you wish, you can actually assign any channel except 9 through 12 to any function (see pages 20-24). The following chart indicates what each remote control channel number does, and how to transmit each channel number.
TO ACTIVATE THE PANIC FEATURE . . . . . . . . . . Press button 1 (channel 1) for 3 seconds. The parking lights will flash repeatedly and the siren will blare for 30 or 60 seconds (user-selectable), or until you press button 1 again to turn it off.
Anti-CodeGrabbing™ (ACG) with Random Code Encryption A Clifford exclusive that protects you and your automobile from the most effective and onerous car stealing device ever used by car thieves — a code-grabber. Code-grabbers are far more effective and efficient than scanning.
UltraSecure™ Coded Valet Mode Your secret valet code In seconds, thieves can disable all other alarm brands by hotwiring the ignition and flicking an easy to find “hidden” valet switch. Your system has safeguards that absolutely ensure a thief cannot enable the valet mode as a way of “turning off” your system.
To exit valet mode 1. Turn the ignition switch to its “ON” position or start the engine. 2. Flick the switch back to its center position. The LED will turn off to confirm that the system is now in its normal operating mode.
FACT™— False Alarm Control and Test With FACT, you’ll never experience repeated false alarms. If the Insignia Siren goes off, DO NOT remotely disarm the system; allow it to run for the full siren duration.
Remote controlled sensor adjustments Due to ever-changing conditions, all alarms require periodic fine-tuning of their sensors. An improperly adjusted sensor is the most common cause of false alarms. With other alarms, this requires repeated trips back to the dealer.
1. Remotely disarm, then turn on the ignition. The LED status indicator inside your vehicle will blink 1-3 times, pause, then repeat. 2. Count the number of blinks in one cycle between pauses (for you.
Long-term chirp silencing: Whenever you wish, you may silence your XL4000’s arm and disarm chirps until you decide to restore them. The parking light flashes will continue to provide visual confirmation of remote controlled arming and disarming. See User-selectable features on pages 20-24.
User-selectable features Your XL4000 allows you to set many of its features to your own personal preferences. Although the system’s programming capabilities are very extensive, we have made the programming procedures very simple: to make a change, you just flick the PlainView switch a few times.
EXAMPLE 1: Turn on AutoArm & Lock: You can set the system to automatically lock the car doors when the system AutoArms (see page 21). To turn on the AutoArm & Lock feature, you’ll note that “AutoArm & Lock” is in column 3, row 2 of the Table (on pages 23-24).
4. Now look up the location on the table of siren duration. Note that it’s in column 3, row 4 (latched, center, latched, center, latched, center, wait for the 3-chirp/column 3 confirmation, then 4 momentary presses). After a brief pause, you’ll hear two chirps to confirm that the siren duration is now set to 60 seconds.
Table of user-selectable features: 1 chirp = OFF, two chirps = ON. Feature Select Column 1 1st latched Column 2 2nd latched Column 3 3rd latched Row 1 1st momentary Add new remote to channel 1 info on.
Ein wichtiger Punkt beim Kauf des Geräts Clifford XL4000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Clifford XL4000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Clifford XL4000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Clifford XL4000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Clifford XL4000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Clifford XL4000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Clifford XL4000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Clifford XL4000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Clifford XL4000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
