Benutzeranleitung / Produktwartung IT-2000 des Produzenten Casio
Zur Seite of 31
IT-2000 I/O Box Installation Manual (V ersion 1.00 ) A pril 1998 Casio Computer Co., Ltd. Copy right ©1998. All rights r eser ved.
2 Table of Contents Chapte r 1 O v er v iew 3 Chapte r 2 S y stem Confi gur at i on and Installati on M et hod 4 2.1 Opti ons and Sof t w ar e 4 2.2 S y stem Conf i gur at i on 5 2.2.1 With Sing le I/O Bo x 5 2.2.2 With M ultiple I/O B oxe s 5 2.2.3 With Sing le M aste r I/O Box 6 2.
3 1. Ov erview This system performs file transfer and other operations between the Casio Data Collection Term inal IT- 2000 (hereinafter referred to as this terminal or IT-2000) and an AT architecture- based personal computer (hereinafter referred to as PC or Host PC) via the I/O Box.
4 2. Sy stem Configuration and Installation Method 2.1 Options and Softw are Categor y Name Model Remark Hardware Satellite I/O Box Master I/O Box RS-232C cable RS-422 cable SCSI cable IT- 2060IOE IT-.
5 2.2 Sy stem Configuration This system can be configured in various way s. See typical exam ples of the hardware configuration as below. 2.2.1 With Single I/O Box Fig.
6 Software Hardware PC side IT- 2000 side Satellite I/O Box RS-232C cable RS-422 cable IT- 2000 PC Upload/Download Utility FL INK of Windows3.1 v ersion or FL INK of MS-DOS version Table 2.3 Hardware and software configuration with multiple Satellite I/O Boxes 2.
7 Software Hardware PC side IT- 2000 side Master I/O Box SCSI cable IT- 2000 PC SCSI Board Upload/Download Utility FL INK of Windows3.1 v er. or FL INK of MS-DOS ver. Table 2.5 Hardware and software configuration with multiple Master I/O Boxes 2.2.5 With Master and Satellite I/O Boxes Fig.
8 2.3 Installation Method This section describes the installation and setup procedures that must be perform ed before I/O Box and PC operations are started. The following diagram shows a flow of the setup procedure. Note: For inform ation about the installation procedure of the Upload/D ownload Utility refer to the Upload/Download U tility Manual.
9 2.3.1 Setup of Satellite I/O Box The following paragraphs explain how to set up the Satellite I/O Box and Master I/O Box to be connected to the PC. Note that the DIP switch settings of the Satellite I/O Box differ depending on the connection with single Satellite I/O Box or multiple Satellite I/ O Boxes.
10 Make sure that the POWE R switch of the I/O Box is set to OFF . Set the D IP switch of the first I/O Box to be connected to the PC directly as follow s. 123456 789 1 0 ON OF F OFF OF F OFF OF F ON ON ON ON Set the DIP switch of other I/ O Boxes to be connected under daisy-chain as follows .
11 2.3.2 Setup of Master I/O Box Note that the DIP switch settings of the Master I/ O Box differ depending on whether the system configuration is consisted of only single Master I /O B ox or of multiple Master I /O B oxes that are followed by Satellite I /O Boxes.
12 Power SC SI termination 10 Supplies power ON Does not supply pow er OFF Connect the first I/O Box and PC with the SCSI cable. Then connect the SCSI connector of the I /O Box connected to the PC to the SCSI connector of the other I/O Box v ia the SCSI cable.
13 2.3.4 Setup of PC Connection If using the Satellite I /O B ox, plug the connection cable into the COM port of the P C. If using the Master I /O Box, plug the connection cable into the SCSI board of the PC. Startup Fi rst turn ON the power to each I/O Box, then turn ON the PC power to start up Windows95 and start up the Upload/Download U tility.
14 Environment Set up If the I /O Box to be connected to the P C is a Satellite I/O Box, select "RS-232C" from the "Configure" menu of the Upload/Download Utility, then select "Settings" from the same m enu. Fi g. 2.8 RS-232C Main Menu screen In the COM PORT field select the COM port number in the PC to be used.
15 3. Operation Method After connecting the necessary sy stem devi ces and installing the software on the P C, perform file upload/download with the following procedure. On this system each function will be executed if the IT-2000, which has started up the F LI NK Utility, is m ounted on the I/O Box after the P C-side utility was started up.
16 Set any "Options" item, if necessary . Set the "Mode" option, if necessary . Click on the [OK] button. If preparation has been com pleted on the IT-2000 side, the progress bar will be display ed and file uploading will begin.
17 3.1.2 Specify ing Files from IT-2000 Operation on PC Start up the Upload/Download Utility on the PC and select "Link Manager Start" from the "Exe cute " menu.
18 FLINK.DLL of Window s 3.1 version Start up Windows 3.1. Start up FL INK with the appropriate param eters. DoFLINK ( argc, argv ) argc = 4; argv[ ]= { "fl" , "/s", "D: FILE", "C: yy" } This transfers D: FIL E from the IT- 2000 to C: yy on the PC.
19 3.2 File Dow nload Transfer files from the PC to the IT-2000. There are two methods for specify ing the files to be downloaded: specifying files from the PC , and specifying files from the IT-2000.
20 Operation on IT-2000 FLINK.EXE of MS-DOS version Start up MS-DOS. Start up FL INK without adding any parameters. "Wait..." is display ed on the IT-2000 screen and the idle m ode is set. FLINK.DLL of Window s 3.1 version Start up Windows 3.
21 3.2.2 Specify ing Files from IT-2000 Operation on PC Start up the Upload/Download Utility on the PC and select "Link Manager Start" from the "Exe cute " menu.
22 FLINK.DLL of Window s 3.1 version Start up Windows3.1. Start up FL INK with the receiv e mode option. DoFLINK ( argc, argv ) argc = 4; argv[ ]= { "fl" , "/r", "C: FILE", "D: yyy" } This transfers C: FIL E from the PC to D: yyy on t h e IT - 2000.
23 4. Error Codes and Error Messages Any term ination codes and error information generated by the PC will be recorded in the error log file on the PC. This error log file will be created according to the file name specified by the DE VICE.INI file (configuration file), and each new log entry will be appended to the file.
24 Error Code Error Message Description Rem edy Categ. D etai 0x00 0x00 Norm alEnding Normal en d. - 0xDC 0x00 A DriveForm atNotice Format notification of drive A - 0xF5 0x 00 ZDriveFor matNotice Format notification of drive Z - 0xF8 0x 00 BreakK eyInte rruptEndingNotice Notification of abor tio n by user.
25 Error Code cate g Detai Error Message Descriptio n Re m edy 0x0 4 0x0 0 Rea dOnl y File A ccessError W rite is spec i f ied to read-onl y - f ile. Change the f ile attribution f or w rite. 0 x 0 5 0 x 0 0 Co mm unicationEr ror Co mm unication er ror.
26 5. Q and A Common to Satellite and Master I/O Boxes Q1 It seem s that it takes a rather long time for comm unication to start, doesn't it? A1 Communication between the I T-2000 and Satellite/Master I/O Box is performed according to I rDA protocol.
27 Q2 If the Windows3.1 v ersion of FL INK is used, the baud rate setup cannot be m odified by changing the DIP switch setting for the RS-232C communication speed on the Satellite I /O Box. Why? A2 To modify the RS-232C com munication speed with the Windows3.
28 Q2 What is the maxim um baud rate if the Satellite I/O Boxes are connected under daisy -chain so they follow each Master I/O Box ? A2 In this case the phy sical Master I/O Box-to-Satellite I /O Box speed is 115200 bps max. Q3 Can I update the v ersion of Master I/O Box firmware ? A3 Yes, by using the dedicated download tool and a SCSI cable.
29 6. Reference Manuals Besides this IT-2000 I /O Box Installation Manual, the following m anuals are available for the IT-2000 sy stem as application program development m anual.
30 7. List of SCSI Boards and SCSI Cables The listed SCSI Boards and Cables below have been assessed for the operability with the I T-2000. Thus, they are recom mended for use with the I T-2000.
31 A ppendix Installation Method of Upload/Dow nload Utility Installation The Upload/Download U tility software consists of the following software com ponents: Fil e n a me Re ma rk LMWI N32.EX E Execution module of the Upload/Download Utility (GUI mode) driver32.
Ein wichtiger Punkt beim Kauf des Geräts Casio IT-2000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Casio IT-2000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Casio IT-2000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Casio IT-2000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Casio IT-2000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Casio IT-2000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Casio IT-2000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Casio IT-2000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Casio IT-2000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
