Benutzeranleitung / Produktwartung 1650 des Produzenten Canon
Zur Seite of 71
1 AXIS 1650 User’s Manual AXIS 1650 User’s Manual The Network Print Server for Canon Printers and Multifunctional Products * Including support for the host-based printing methods Canon Advanced Pr.
Safety Notices AXIS 1650 User’s Manual 2 Safety Notices Take some time to read through the safety notices before inst alling the print server. Please obs erve all safety markings and instructions when using this product. Important: Observe “Important:” in the text to avoid operational impairme nt.
3 AXIS 1650 User’s Manual Safety Notices Liability Every care has been taken in the preparation of this manual; if you dete ct any inaccura cies or omissions, please inform your lo cal Axis office, which can be found on the co ver of this document.
AXIS 1650 User’s Manual 4 Table of Contents About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 About Axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 AXIS 1650 User’s Manual P r eface Thank you for purchasing the AX IS 1650. This product has been developed to connect your printer anywhere in your network, allowing all network users access to sh ared printer resources. About this Manual This manual is applicable for the AXIS 16 50 print server with firmware version 1.
AXIS 1650 User’s Manual 6 Support Services Should you require any technical a ssistance, please contact your Axis reseller. If your questions cannot be answered immediate ly, your Axis reseller will forward your queri es through the appropriate channels to ensure a rapid response.
7 AXIS 1650 User’s Manual Product Overview Section 1 Product Overview Package Contents Hardware Model Model/ Part Number Network Print Server AXIS 1650 0214-001- XX With firmware version 1. 00 or higher Adhesive Holder & Cl ip ACC AXIS CLIPS K 20119 USB Cable 70 cm, 28 inc hes USB cable supports USB Low-Speed and Full-Speed.
Product Overview AXIS 1650 User’s Manu al 8 The AXIS 1650 Network Print Server Supported Printers AXIS 1650 is developed to network Canon printers and multifunctiona l products.
9 AXIS 1650 User’s Manual Product Overview Installation and Integration The installation of the AXIS 1650 and its integration into the network is performed using one of these software combinations: .
Product Overview AXIS 1650 User’s Manu al 10 Future proof: You can upgrade the AXIS 1650 Flash memory over the network. This allows you to quickly update and enhance the operational features of your AXIS 1650 when new print server softwar e becomes available.
11 AXIS 1650 User’s Manual Print Server Installation Section 2 Print Server Installation Follow these steps to install and configure your AXIS 1650: 1. Connect the Hardware Backside label of print server 1. Connect the Hardw are , on page 11 2. Set the IP Address , on page 13 3.
Print Server Installation AXIS 1650 User’s Manual 12 1. Make sure that your printer is switched off and that the print server’s power adapter is disconnected . 2. Locate the serial number , found on the underside label of th e print server, and write it down.
13 AXIS 1650 User’s Manual Print Server Installation 2. Set the IP Address • Before setting the IP address, ma ke a note of the print server’s serial number (S/N), located on its backside label. See Backside label of print server , on page 11. • You should obtain an unused IP a ddress from your network administrator.
Print Server Installation AXIS 1650 User’s Manual 14 Set a Static IP Address using AXIS IP JumpStarter AXIS IP JumpStarter is an application that helps you to locate your Axis print server on the network and assign an IP address to it. 1. Install AXIS IP JumpStarter, it is availa ble on the AXIS 1650 CD and on www.
15 AXIS 1650 User’s Manual Print Server Installation 4. Click the radio button that corresponds to your choice of IP setting method (static or dynamic using DHCP). When assigning a static IP address you also have to define the Subnet Mask and Default Gateway .
Print Server Installation AXIS 1650 User’s Manual 16 Set a Static IP Address using ARP in Windows 98/Me/2000/XP/2003 1. Open a Command Prompt and type: Example: 2. If the host returns Reply from 192.168.3.191 ... or a similar message, the IP address has been set successfully.
17 AXIS 1650 User’s Manual Print Server Installation Set a Static IP Address using ARP in UNIX Follow the instructions below to set the IP address using ARP. 1. Type the following comman ds in the shell window: Example: 2. The host will return 192.168.
Print Server Installation AXIS 1650 User’s Manual 18 Set an IP Address with NetSpot Device Installer software NetSpot Device Installer is software from Canon that allows yo u to assign an IP address and manage Canon devices connected to your network.
19 AXIS 1650 User’s Manual Print Server Installation Set the IP address using NetS pot Device Installer Follow these instructions to set the IP address using NetSpot Device Installer: 1. Start the program. The main wi ndow will open. After a while a list of devices detected on the network will be displayed.
Print Server Installation AXIS 1650 User’s Manual 20 5. Next, configure the TCP/IP protocol: 6. After you have finished the configuration, click OK . 7. Click OK . Your printer’s protocol configuration is no w finished and your AXIS 16 50 has received an IP address.
21 AXIS 1650 User’s Manual Print Server Installation IP Address Host Names If you are using host names, you can map a unique host name to the IP address. Refer to your system manuals or to your network administra tor for instructions on how to perform name mapping on your system.
Windows Installation AXIS 1650 User’s Manual 22 Section 3 Windows Installation Installing Printer Ports using AXIS CAPT Print Monitor AXIS CAPT Print Monitor is a Windows component that has been developed for network printing.
23 AXIS 1650 User’s Manual Windows Installation Print Server Installation using AXIS CAPT Print Monitor in Windows 2000, XP and Server 2003 1. Install the AXIS CAPT Print Monitor on your works tation. The software is available on the AXIS 1650 CD and on www.
Windows Installation AXIS 1650 User’s Manual 24 4. Leave this check-box unchecked* and click Next . Windows XP/Server 2003 only: Make sure the Allow this applicati on to process incoming network print er information on the local subnet checkbox is checked.
25 AXIS 1650 User’s Manual Windows Installation 5. Click Finish to finish the installation. 6. Windows XP/Server 2003: Go to Start | Printers and Faxes and click the Add a Printer icon to start the Add Printer Wizard. (Windows XP Home Edition: Start | Control Panel | Printers and Faxes | Add a Printer ).
Windows Installation AXIS 1650 User’s Manual 26 7. Select Local Printer attached to this computer. Make sure the Automatically de tect and install my Plug and Play printer check box is not checked. Click Next. 8. Click the Create a new port radio-button and select AXIS CAPT Port*.
27 AXIS 1650 User’s Manual Windows Installation 9. The AXIS CAPT Port pop-up window will a ppear. Select your AXIS 1650 from the Availabl e network printers list and click OK . 10. Select Manufacturer and Printer from the driver list. Click Next . 11.
Windows Installation AXIS 1650 User’s Manual 28 13. Choose whether you want to share the printer wi th other network users, print a test page, etc. Select the appropriate radio button and click Next and Finish . 14. Print a test page to verify. You have now completed the installation.
29 AXIS 1650 User’s Manual Windows Installation Print Server Installation using AXIS CAPT Print Monitor in Windows 98 and Me Follow the procedure below to install TCP/ IP Ports from a Window s 98 /Me workstation: 1. Install the AXIS CAPT Print Monitor on your works tation.
Windows Installation AXIS 1650 User’s Manual 30 4. Leave this check-box unchecked* and click Next . (*If you want to disable broadcast st atus updates and enable unicast, See Enabling Unicast Network Communication on page 58 for instructions.) 5. Click Finish to finish the installation.
31 AXIS 1650 User’s Manual Windows Installation 8. Choose an appropriate printe r driver for your printer. If the desired printer driver is not available, click the Have Disk... button. Insert the printer driver CD that was provided with your printer, select the CD drive and click OK.
Windows Installation AXIS 1650 User’s Manual 32 Print Server Installation using the Standard TCP/IP Port in Windows 2000/XP/2003 Follow the instructions below to use the Windows Standard TCP/IP Port to add a network printer in Windows 2000/ Windows XP/2003.
33 AXIS 1650 User’s Manual Windows Installation 4. In the Printer Name or IP Address field, enter the IP address of the print server ( Example: 192. 168.3.191 ) The Port Name field will be filled in automatically. Click Next . 5. Select Manufacturer and Printer from the lists.
Windows Installation AXIS 1650 User’s Manual 34 8. Next, from your desktop, go to Start | Printers (and Faxes). Highlight the installed printer and right-click, choose Properties, then Ports | Configure Port. 9. In the LPR Se ttings - Queue Name field, you will see the value "z".
35 AXIS 1650 User’s Manual Print Server Ma nagement and Configuration Section 4 Print Server Management and Configuration The management and configuratio n tools that are supported by the AXIS 1650 .
Print Server Management and Configuration AXIS 1650 User’s M anual 36 Print Server Management from the Embedded Web Pages All Axis print servers contain an embedded web server that can be accessed through a web browser.
37 AXIS 1650 User’s Manual Print Server Ma nagement and Configuration Accessing the Embedded Web Pages Follow these steps to access the AXIS 1650 embedded web pages: 1. Enter the print server’s IP address (or host name) in the Location/Address field of your Web browser.
Print Server Management and Configuration AXIS 1650 User’s M anual 38 Available Services from the User Mode The following services are available from the Us er mode.
39 AXIS 1650 User’s Manual Print Server Ma nagement and Configuration Serial Number Every Axis device is uniquely identified by its serial number. The serial number is found on the under side label of your pr int server . Language English and Japanese is supported in the print se rver's web interface.
Print Server Management and Configuration AXIS 1650 User’s M anual 40 Help The Help pages present basic information abou t the AXIS 1650 and the Web user interface. Available Services from the Admin Mode The following services are available from the Admin mode.
41 AXIS 1650 User’s Manual Print Server Ma nagement and Configuration System Location This parameter allows you to specify where the network printer is physically located in your organization. This enables you to find the prin ter to which you have sent your print jobs.
Print Server Management and Configuration AXIS 1650 User’s M anual 42 Community Name: Specify the community name for SNMP. Up to 32 alphanumeric characters can be entered.
43 AXIS 1650 User’s Manual Print Server Ma nagement and Configuration SNMP Restriction Mode: • Accept Only users specified in [SNMP restrict ion IP address list] are permitted to specify/browse the settings for the device using the SNMP protocol.
Print Server Management and Configuration AXIS 1650 User’s M anual 44 Serial Number Every Axis device is uniquely identified by its serial number. The serial number is found on the under side label of yo ur print server. See Print Server Installation , on page 11.
45 AXIS 1650 User’s Manual Print Server Ma nagement and Configuration Print Jobs From the Print Jobs page you can view Printer Usage that displays the accumulated usage of the printer connected to your print server.
Print Server Management and Configuration AXIS 1650 User’s M anual 46 DHCP Enabled Select the appropriate radio button to enable DHCP (Dynamic Host Configuration Protocol). DHCP automatically downloads the IP address to ea ch print server at startup.
47 AXIS 1650 User’s Manual Print Server Ma nagement and Configuration Subnet Mask Specify the subnet mask used for determining when the traffic should be sent via a router. This number combined with the IP address identifies on which network the prin t server is located.
Print Server Management and Configuration AXIS 1650 User’s M anual 48 WINS Enabled Select the appropriate radio button to enable WINS (Windows Internet Name Service) over TCP/IP. WINS uses NetBIOS names to allow Window s-based clients to locate resources on TCP/IP networks.
49 AXIS 1650 User’s Manual Print Server Ma nagement and Configuration SNTP update interval SNTP update interval: The interval the print server shall send a request to the Time Server for a updated time. Default = 1hours Time Zone (Only visible in English firmware version) Specify the time zone for yo ur print server location.
Print Server Management and Configuration AXIS 1650 User’s M anual 50 AXIS Online Services Click the print server product page to receive information about your print server model. The product page, available on the Axis Web Site, offers you up-to-date information, print server manuals, FAQs, software updates and technical support, etc.
51 AXIS 1650 User’s Manual Print Server Ma nagement and Configuration Print Server Management Using FTP Having assigned an IP address to your AXIS 1650, as described in 2. Set the IP Address , on page 13, you can change the AXIS 1650 parameter se ttings using the File Transport Proto col (FTP).
Print Server Management and Configuration AXIS 1650 User’s M anual 52 Example: How to edit the config file using FTP from a Command prompt. FTP Hel p By typing help in step 3 in the FTP instructions describe d above, a list of a ll available files and commands will be displayed.
53 AXIS 1650 User’s Manual Print Server Ma nagement and Configuration Print Server Management Using SNMP You can use SNMP (Simple Network Management Protocol) for remotely monitoring and configuring the AXIS 1650. All major fu nctions for print servers are supported.
The Test Button AXIS 1650 User’s Manu al 54 Section 5 The Test Button The test button is located on the front right hand side of the print server and is used to perform a Factory Default: 1. Remove the external power supply to switch off the print server.
55 AXIS 1650 User’s Manual Upgrading the Firmware Section 6 Upgrading the Firmware The print server’s firmware* is stored in its Flash memory. This memory retains data con tent even after the power is removed.
Upgrading the Firmware AXIS 1650 User’s Manual 56 Upgrading using FTP • To upgrade over the network using FTP you w ill need a file with the new print server firmware. The name of this file is in the form product_version.bin . • The print server must have a valid IP address.
57 AXIS 1650 User’s Manual Upgrading the Firmware 13. When you see a new ftp prompt the procedure has successfully been completed. Notes: • If the upgrading process fails, just re peat the instructions presented above. • If you lose contact with the AXIS 1650 after an upgrading failure, just restart the AXIS 1650 to restore con tact.
AXIS 1650 User’s Manual 58 Appendix A Enabling Unicast Network Communication AXIS CAPT Print Monito r uses broadcast communication, so that status information from the print server can be shared between severa l users without elevating ne twork traffic.
59 AXIS 1650 User’s Manual 6. Open the config file using any text editor: 7. Locate the parameter named USE_IP _PORT_NAME: type YES 8. Once the editing is complete, save the file as config 9. In the Command promp t window, upload the configuration file to the AXIS 1650 by typing put config CO NFIG 10.
AXIS 1650 User’s Manual 60 11. Install AXIS CAPT Print Monitor software on your workstation. The software is available on the AXIS 1650 CD and on www.axis.com. Click your way through the program. 12. During the software setup, you will reach the Set the Unicast Communication Mode screen, check the Enable unicast check-box.
61 AXIS 1650 User’s Manual 16. Click the Create a new port radio-button and select AXIS CAPT Po rt. Click Next. 17. A pop-up window will appear. Enter the IP address of the AXIS 1650. 18. Select Manufacturer and Printer from the driver list. Click Next .
AXIS 1650 User’s Manual 62 Appendix B Internet Connection Firewall in Windows XP SP2 If you have upgraded to Windows XP SP2, you need to open UDP port 10260 in the Internet Connection Firewall when using Broadcast co mmunication. For Unicas t comunication, the firewall can remain closed.
63 AXIS 1650 User’s Manual 3. Make sure On i s selected. “Don’t allow except ions” and “Off” must be unchecked! 4. Click Exceptions and highlight AXIS CAPT Port .
AXIS 1650 User’s Manual 64 Note: If you accidentally delete the AXIS CAPT Port and want to recreate it, go to Exceptions | Add Port and configure the port.
65 AXIS 1650 User’s Manual Technical Specifications Supported Printers AXIS 1650 is developed to network Canon printers and multifunctional products. AXIS 1650 supports host-based printing methods such as Canon Advanced Printing Technology, Canon Advanced Raster Printing System and other printer types such as Canon BubbleJet.
AXIS 1650 User’s Manual 66 Supported Language s English and Japanese. Logical Connection Supports NWay that provides auto-detection of network speed. Use Ethernet II frame type, full duplex. Wired Network Attachments RJ-45 connector (Category 5 shiel ded twisted pair cable) for 10baseT Ethernet or 100base TX Fast Ethernet.
67 AXIS 1650 User’s Manual Environmental Temperature: 40 - 105 °F (5 - 40 °C) Approvals EMC: EN 55 02 4:1998 EN 55 022: 1998 + A1 (CISP R 22:1997 + A1) Class B EN 61000-3-2 :2000 EN 61000-3-3:1 99.
AXIS 1650 User’s Manual 68 A Adhesive Clip 12 Adhesive Holder 12 Admin 36 Assistance 6 B BOOTP 44 Broadcast 62 BSD 17 BubbleJet 54 C Canon Advanced Printing Technology 1, 8, 38, 45, 65 Canon Advance.
69 AXIS 1650 User’s Manual I IEEE 1284 parallel port 10, 66 Installing printer Ports Windows 2000 23, 29 Installing printer ports Windows 2000,XP, 2003 23 Windows 98, Me 29 Internet Connection Firew.
AXIS 1650 User’s Manual 70 R Remote Printer Port 31 Restart 44 Root Password 41 S Serial Number 39, 44 Setting the Internet addr ess ARP 17 SLP enabled 48 SLP restriction enabled 42 SLP restriction .
71 AXIS 1650 User’s Manual TCP restriction mode 42 Technical Assistance 6 Test Button 54 Test Page 54 TFTP 44 This Print Server 40 Time Zone 49 two connected printers 10 U UDP port 10260 62 UNIX 17 .
Ein wichtiger Punkt beim Kauf des Geräts Canon 1650 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Canon 1650 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Canon 1650 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Canon 1650 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Canon 1650 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Canon 1650 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Canon 1650 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Canon 1650. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Canon 1650 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
