Benutzeranleitung / Produktwartung Mag 20 Dt/Hs des Produzenten Cannon
Zur Seite of 28
OWNER’S MANU AL NOTE: Do not return your CANNON® Do wnrigger to your retailer. Your retailer is not authorized t o repair or replace this unit. You may obtain service b y: • calling CANNON® at 1.
2 Parts Description 1. Reel This is used to spool the cable, available in length s ranging from 1 50 to 400 feet. 2. Boom This is used to extend the weight out from the body of the downrigger and has a pulley fixed to its end. Boom lengths range from 24 to 53 inches.
3 Mag 20 DT New Features Magnum Power The Mag 20 DT/HS and Mag 20 DT/TS feature improved tolling weight capacity, retrieval rate, and quality. The Mag 20 DTs can now accommodate trolling weights up to 20lbs. The newly improved Mag 20 DTs also feature a high retrieval rate up to 250 feet per minute.
4 Downrigger Mounting on Boat s A downrigger should be mounted where ever it is easy to operate and observe. You want to be able to see your fishing rod and to react quickly. So, choosing a good spot to mount your downrigger on your boat is 99% of the job.
5 Side Rail Mounting Side/Rail mounts can be mounted to a welded T section. They can also be used at the two rail section butt joint. In both installations it is recommended to use a non-slip material, such as rubber or a thin wood sheet, between metal surfaces.
6 NOTE: When using the telescopic boom, we strongly recommend the use of a deck plate on all boats to provide adequate stability for the downrigger. The Low-Profile Swivel Base mounting follows the sa.
7 Mounting the Downrigger on the Base Slide body over the lip of the base, with boom outboard or facing the stern. Lift Lock Knob to hold threaded shaft clear of base until body completely covers base. Turn Lock Knob clockwise to tighten the downrigger to the base.
8 T erminating the Downrigger Cable Cannon Uni-Release The Cannon Uni-Release attaches directly to the downrigger weight. Attach fishing line to the clip at the end of the release, and then click through a series of increasing tension settings.
9 CAUTION: This rod holder is intended for use of up to 30 lb. test line only, and is not recommended for use with any tackle IGFA rated higher than 30 lb. A safety strap (not included) is recommended for all applications. The rod holder assembly is not warranted when used with tackle above 30 lbs.
10 Wiring Y our Downrigger Your Boat's Electrical Condition It is important to make sure that your boat is properly set up before installing your Mag 20 DT with Positive Ion Control (PIC). Whenever a boat is in water, various submerged parts interact to create weak electrical currents.
11 FUSE / BREAKER SPECIFICATI ONS: 30 Amp, 32 Volt, waterproof, fast blow. WIRE SPECIFICATIONS: 0-15 ft. (0-5 meters) 10 gauge 15-25 ft. (5-8 meters) 8 gauge 25-30 ft. (8-9 meters) 6 gauge CAUTION: When using wire longer than that provided with your unit, follow the above chart.
12 Clutch Knob 3-Position Motor Swit ch Operating Y our Downrigger After mounting the Cannon downrigger to your boat, release some line from your rod and reel so that the lure is anywhere from 5 to 100 feet behind the boat. Tthis is called drop back. Attach the fishing line firmly into the line release.
13 NOTE: Make sure that the clutch is well tightened when using powered descent or ascent. NOTE: Actual fishing depth may vary from depth shown on meter due to trolling speed and weight of cannon ball. (See "Blowback") NOTE: If your reel continues to slip no matter how hard you tighten the brake adjust knob, try this suggestion.
14 The Short S top System The Short Stop system is composed of three critical components: the electronic unit, the reel set screw, and the trolling weight insulat or. While the downrigger cable is in the water, there is a minute electrical current that flow s between the cable and the grounded metal boat components in the water.
15 How the Positive Ion Control System Works The PIC system uses an internal circuit that passes the voltage through the drive train of the Mag 20 DT to the reel set screw. The set screw contacts the cable. Care must be taken to ensure contact between the cable and the set screw when replacing the cable.
16 Blowback Simply stated, blowback is what happens to the downrigger weight when you pull it through the water behind your boat. As your speed increases, so does the horizontal distance between the weight and your downrigger. The faster you go, the farther the weight is behind you.
17 T rouble Shooting PROBLEM: Up or down will not work. SOLUTION: Check the battery cable polarity then check the battery voltage. A properly connected and charged battery is important for safety and for proper operation of the downrigger.
18 T en Good T r olling Tip s 1) Test your lures over the boat side before sending them down and back. Do this to make sure the lure wiggles and wobbles properly without going belly up or wandering off. Some lures can be adjusted, fine tuned actually, to impart maximum action.
19 CANNON® LIMITED W ARRANTY Johnson Outdoors Inc. warrants to the original purchaser that if the accompanying product (see exclusions below) proves to be defective in material or workmanship within the following warranty periods, Johnson Outdoors Inc.
20 Authorized Service Centers Your new Cannon® Downrigger was built to exacting specifications under rigid quality control to p rovide you years of trouble-fr ee operation. If it should ever need adjustment or serv ice, you may send it to any Cannon® Authorized Service Center near you.
TM MAG 20 DT/HS 1902200 Form No. 3394903 Rev 12/06.
1 3392500 FRAME - LARGE BLACK (LEXAN) 42 0467695 BRAKE PLATE - REEL 83 9430160 >WASHER - STAR 5/16" [3.EA] 2 4427005 NOSE DECAL MAGNUM 43 1264670 CLUTCH PAD 84 2277002 >UNIVERSAL LINE RELEA.
TM MAG 20 DT/HS/E 1902201 Form No. 3394922 Rev 12/06.
1 3392500 FRAME - LARGE BLACK (LEXAN) 42 9250002 PIN - DRIVE SHAFT 3/16" ROLL SS 83 9340101 >SCREW - SET 3/8"-16 x 5/8" [2.EA] 2 4427005 NOSE DECAL MAGNUM 43 0467695 BRAKE PLATE - REEL 84 9430160 >WASHER - STAR 5/16" [3.
TM MAG 20 DT/TS 1902205 Form No. 3394908 Rev 12/06.
1 3392505 FRAME - LARGE WHITE (LEXAN) 40 1480070 SHAFT - DRIVE 79 9430160 >WASHER - STAR 5/16" 2 4427005 NOSE DECAL MAGNUM 41 9250002 PIN - DRIVE SHAFT 3/16" ROLL SS 80 2200109 >OFFSHO.
TM MAG 20 DT/TS/E 1902206 Form No. 3394921 Rev 12/06.
1 3392505 FRAME - LARGE WHITE (LEXAN) 41 1480070 SHAFT - DRIVE 81 2200109 >OFFSHORE SALTWATER RELEASE 2 4427005 NOSE DECAL MAGNUM 42 9250002 PIN - DRIVE SHAFT 3/16" ROLL SS 82 3992300 SWIVEL H.
Ein wichtiger Punkt beim Kauf des Geräts Cannon Mag 20 Dt/Hs (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Cannon Mag 20 Dt/Hs noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Cannon Mag 20 Dt/Hs - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Cannon Mag 20 Dt/Hs reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Cannon Mag 20 Dt/Hs erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Cannon Mag 20 Dt/Hs besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Cannon Mag 20 Dt/Hs verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Cannon Mag 20 Dt/Hs. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Cannon Mag 20 Dt/Hs gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
