Benutzeranleitung / Produktwartung 1500 des Produzenten BT
Zur Seite of 68
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Us e r G u i d e B T S TUDIO 1500.
Section B T Studio 1500 – Edition 3 – 27.07.04 – 5876 12 Minutes digital recording time with a capacity for up to 59 messages. Access your messages from any other modern telephone. Use Caller Display to see who is calling before you pick up the phone and keep track of incoming calls with the 30 number Calls list.
Section B T Studio 1500 – Edition 3 – 27.07.04 – 5876 This User Guide provides you with all the information you need to get the most from your phone. Before you make your first call you will need to set up your phone. Follow the simple instructions in ‘Getting Started’ , on the next few pages.
Getting started Location . . . . . . . . . . . . . . . . . . . . . . 6 Setting up the base and handset . . . . 6 Getting to know your phone Handset buttons . . . . . . . . . . . . . . . . 10 Sample screen . . . . . . . . . . . . . . . . . . 11 Base buttons and LEDs.
5 In this guide B T Studio 1500 – Edition 3 – 27.07.04 – 5876 T o change the ringer melody . . . . . . . 34 T o change the ringer volume . . . . . . . 35 Reset handset and base . . . . . . . . . . . 35 Reset if you have forgotten your PIN code .
If you have purchased a BT Studio 1500 T win please follow instructions and Location Y ou need to place your BT Studio 1500 close enough to a mains power and telephone socket so that the cables will reach. The strength of the handset signal depends on where you site the base.
7 Getting started T alk/Standby time In ideal conditions, the handset batteries should give about 10 hours talk time or 100 hours standby on a single charge. The base must remain plugged in to the mains and switched on at all times. Note that new batteries do not reach full capacity until they have been in normal use for several days.
BT Studio 1500 T win handset Y our BT Studio 1500 handsets are the same, so instructions throughout this guide apply to both. Handset numbers Once registered with the base, each handset will display its handset number, and respectively.
2. Plug the power adaptor into the mains wall socket and switch the power on. 3. Install the 2 x AAA rechargeable batteries supplied into the second handset. 4. Place the handset in the charger and charge the handset for at least 16 hours. The red Charging light on the charger comes on.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Getting to know your phone 1 2 3 4 5 6 7 8 9 0 R Int Clr Re dial D i g i t a l C l a r i t y P C a l l s G H I P Q R S A B C J K L T U V D E F M N O W X Y Z Vol Menu S e c r e c y Redial/P Opens the redial list, page 16 .
11 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 STUDIO 1 EXT INT Getting to know your phone Sample screen – These are where the handset icons will appear. * For these features to work you must subscribe to your Network Provider’s Caller Display and/or Call Waiting service.
12 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Getting to know your phone Base buttons and LEDs Play Del O G M O n / O f f A n s C h a r g i n g P o w e r / I n U s e S k i p S t o p S k i p V o l V o l DECT Digital Clarity Page B T S t u d i o 1 5 0 0 Ans On/Off Switches the answering machine on/off, page 37 .
PHONEBOOK ADD ENTRY DELETE ENTRY MODIFY ENTRY SET UP BASE VOLUME BASE MELOD Y DEL HANDSET PIN CODE DIAL MODE DEF AUL T HANDSET BEEP INT RING VOL EXT RING VOL INT MELOD Y EXT MELOD Y AUT O ANSWER NAME LANGUAGE KEY LOCK REGISTER SELECT BASE REG BASE 13 B T Studio 1500 – Edition 3 – 27.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Switching the handset power on/off Press and hold the button. Make an external call 1. Press listen for the dial tone then dial the number. The display shows the icons. Preparatory dialling 1. Enter the number first.
15 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 If you have subscribed to your network’s Caller Display service, the caller’s number, or name (if an exact name/number match is found in the phonebook) will also be displayed, See page 23 .
16 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Handset ringer volume There are 3 volume levels to select from, or you can set the volume to off. While the phone is ringing: 1. Press to increase or to decrease the ringer volume. The display shows the set volume.
17 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Press to exit a menu. Keep pressing to return to the idle display at any time. If a name/number match is found in the phonebook the name will be displayed instead of the number. Press to toggle between the name and number.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Store a phonebook entry Y ou can use the phonebook to store up to 30 names and numbers for easy dialling. Each number can be up to 20 digits and each name up to 12 characters long. 1. Press to display PHONE BOOK .
19 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Character map Digit button BLANK - 1 ABC 2 DE F 3 GHI 4 JK L 5 M NO 6 PQ R S 7 TU V 8 WX Y Z 9 9 W X Y Z 8 T U V 7 P Q R S 6 M N O 5 J K L 4 G H .
20 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Dial a phonebook entry 1. Press . 2. Use or to scroll through the entries or enter the first letter of the name you want using the keypad, then scroll to the exact entry using or . 3. Press to dial the number.
21 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 T o delete digits Press . T o change individual characters Use or to move the cursor underneath the letter you want to change, then overtype the correct letter. Vol Clr S e c r e c y Edit a phonebook entry 1.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 If you subscribe to a Caller Display service you can see your caller’s number on your handset’s display (unless it has been withheld) before you answer the call. If you have stored the caller’s name and number in the phonebook they will be shown alternately in the display.
23 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Using the calls list with additional handsets If you are using more than one handset, each handset has a separate calls list. What type of call? The icon indicates a new call waiting to be viewed.
24 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Delete all calls list entries 1. Press or to open the calls list. 2. Press and hold until DELETE ALL? is displayed. 3. Press to confirm (or to cancel). Copy a calls list entry to the phonebook 1. Press or repeatedly to open the calls list and scroll to the entry you want to copy.
25 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 The second caller is only charged from the second you answer, not while they are waiting to be connected.
Section B T Studio 1500 – Edition 3 – 27.07.04 – 5876 The default setting is 1. Y ou can also assign a different ringer melody to entries in your phonebook, see page 18. Y ou can choose a range of settings to suit your personal preferences. Handset ringer melody and volume Y ou have a choice of 3 melodies and 3 volume levels (or OFF).
27 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Handset settings The default setting is 1. T o change the external ringer volume 1. Press . 2. Press or until HANDSET is displayed and press . 3. Press or until EXT RING VOL is displayed then press .
28 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Handset settings T o change the internal ringer volume 1. Press . 2. Press or until HANDSET is displayed and press . 3. Press or until INT RING VOL is displayed then press . The current setting is played.
29 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Handset settings The default setting is ON. Switch beeps on/off 1. Press . 2. Press or until HANDSET is displayed and press . 3. BEEP is displayed, press . 4. Press or to display the type of beeps you want, then press .
30 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 3. Press or until AUTO ANSWER is displayed then press . 4. Press or to select ON or OFF then press . Selecting a language 1. Press . 2. Press or until HANDSET is displayed and press . 3. Press or until LANGUAGE is displayed and press .
31 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Key lock Y ou can lock the keypad so that it cannot be used accidentally while carrying the handset around. T o switch key lock on: 1. Press . 2. Press or until HANDSET is displayed and press . 3.
32 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 T o switch key lock off: 1. Press any key and the display shows PRESS * . 2. Press and the display returns to the idle screen. Naming a handset Each handset registered to the base is assigned a number.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 The default setting is 0000. Y ou can choose a range of settings to suit your personal preferences. Security PIN Y our B T Studio 1500 has a security PIN code which you will need to change some of the base settings.
34 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Base settings De-register a handset from the base 1. Press . 2. Press or until SETUP is displayed then press . 3. Press or until DEL HANDSET is displayed then press . 4. Display shows PIN? Enter your 4 digit PIN then press .
35 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Base settings The default setting is 3. WARNING If you reset the handset and base, you will lose any names or numbers stored in the phonebook, redial list and calls list. Any other settings will also be set back to the factory default.
36 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Base settings Reset if you have forgotten your PIN code 1. Press and hold to switch the handset off and remove the handset batteries, see page 14. 2. Press and hold as you replace the batteries. Wait until the display shows DEFAULT .
Y our B T Studio 1500 answering machine uses voice prompts to guide you simply through its operation. Y ou can operate your answering machine from: The base. Remotely, from any other T ouchtone ® telephone, see page 46 . Before first using your answering machine you should set the correct day and time.
2. Press and release or repeatedly to scroll through the days. After the correct setting is announced press . The day is announced followed by the current hour setting. 3. Press and release or repeatedly to scroll through the hours. After the correct setting is announced presss to select.
39 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 During playback: Pause/resume playback. Once repeats the current message, twice plays the previous message. Once plays the next message, twice plays the message after that. Deletes the current message and you hear “Message deleted”.
Outgoing messages The outgoing message (OGM) is the greeting a caller hears when the answering machine picks up their call. Y our B T Studio 1500 gives you a choice of two pre-recorded outgoing messages, one for Answer and Record and one for Answer Only.
2. F or Answer and Record , press or for Answer Only press . The selected message is played. Record your own outgoing message(s) 1. At the base, press and hold until you hear “Please select outgoing message.
Answer delay Answer delay is the number of times your B T Studio 1500 rings before the answering machine picks up the call and starts playing the outgoing message. Y ou can choose between 2 – 9 rings, or Time Saver. The default setting is Time Saver.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 43 Using the answering machine When the answering machine memory is full the message light on the base will flash steadily every half a second. Repeat this step to set and confirm the second and third digits.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 44 Using the answering machine Loudspeaker volume Use the and buttons. V o l V o l Memory full during a call When there is approximately 30 seconds of recording memory left, the caller will hear “Please complete your call within 30 seconds .
45 Using the answering machine B T Studio 1500 – Edition 3 – 27.07.04 – 5876 The settings after a power failure will be: Outgoing message . . . . . . . . . As last set by you Answer Delay . . . . . . . . . . . . . . As last set by you On/Off . .
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Y ou can operate your answering machine from any modern T ouchtone ® phone by calling your B T Studio 1500 and entering a 3-digit security PIN. Using a PIN code prevents other people from accessing your machine without permission.
47 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Operating your answering machine from another phone 1. Dial your number. When you hear the outgoing message, press . 2. The machine announces “Please enter your security code” , use the phone’s keypad to enter your 3-digit PIN.
48 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 T o set a new security PIN. F ollow the voice prompts. T o set the day and time. F ollow the voice prompts when you are asked to “Enter the Day and Time after the tone”. Enter the day: 1= Sunday to 7 = Saturday.
49 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 T o select Answer and Record OGM. T o select Answer Only OGM. T o hear OGM menu again. T o hear main menu again.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 IMPOR TANT Y ou must choose a handset that is GAP compatible to use with your B T Studio 1500. If you purchase a new handset to use with your B T Studio 1500 it will have to be registered to the base.
51 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Using additional handsets Internal calls Y ou can make internal calls between two BT Studio 1500 handsets. 1. Press . 2. Enter the other handset number using the keypad ( or ). The other handset will ring and show the calling handset's number.
52 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Using additional handsets T ransferring calls Y ou can transfer an external call to the other handset. During an external call: 1. Press . Y our caller is put on hold and the other handset will ring.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 IMPOR TANT Y ou can only register your BT Studio 1500 handset to another base if it is GAP compatible. Y ou will not be able to register your BT Studio 1500 handset to a B T Studio or BT Studio 500 base as these products are not GAP compatible.
54 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Using additional bases On the base: 7. Press and hold to put the base into registration mode. The base beeps and the In use light flashes while the handset is registered.
55 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Using additional bases If AUTO is selected the handset will automatically link to another base with a strong signal, if the signal it is currently receiving from its present base becomes very poor.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Problem Possible cause No display The batteries may be flat or dead. Recharge or replace the batteries, see page 7. No dial tone Is the telephone line cord plugged into the telephone wall socket? Check that the base station is connected to the mains power and switched on.
57 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Problems Possible cause No ring on the handset Check that the base station is plugged into the phone socket and that the mains power is switched on. The ringer volume may be set too low for you or it may be switched off.
58 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Help BT Accessories and Replacement Items For a full range of accessories and replacement items for BT products please call 0870 240 5522, or vis.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Safety General Only use the power supply included with the product. Using an unauthorised power supply will invalidate your guarantee and may damage the telephone. The item code for the base mains power supply is 005391.
60 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 General information It is recommended that if you have a pacemaker fitted you check with a medical expert before using this product. Y our product may interfere with other electrical equipment, e.
61 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Environmental Do not expose to direct sunlight. The product may heat up when the batteries are being recharged. This is normal. However, we recommend that you do not place the product on antique/veneered wood to avoid damage.
62 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Guarantee Y our B T Studio 1500 digital cordless telephone answering machine is guaranteed for a period of 12 months from the date of purchase.
63 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Within the 12 month guarantee period: If you experience difficulty using the product, prior to returning it, please read the ‘Help’ section beginning on page 56, or contact the B T Studio 1500 Helpline on 0870 605 8047 , 9am–5.
64 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 T echnical information How many telephones can you have? All items of telephone equipment have a Ringer Equivalence Number (REN), which is used to calculate the number of items which may be connected to any other telephone line.
65 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Declaration of Conformance Hereby, Suncorp T echnologies, declares that this B T Studio 1500 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The Declaration of Conformance for the BT Studio 1500 is published on the website: http://www.
66 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 A Pause lasts 3 seconds. Y ou can Pause dialling at any time by pressing the P button. T o insert a pause 1. Begin storing a number and press where a pause is needed. P is shown in the display. Recall The R button is used when connected to certain switchboards, e.
67 B T Studio 1500 – Edition 3 – 27.07.04 – 5876 4. Press or to select either TONE or PULSE then press . 5. Press twice to return to the idle screen. T emporary change to dialling mode If you have set your B T Studio 1500 to Pulse dialling, you can temporarily switch to T one dialling during a call.
B T Studio 1500 – Edition 3 – 27.07.04 – 5876 Offices worldwide The telecommunications services described in this publication are subject to availability and may be modified from time to time. Services and equipment are provided subject to British T elecommunications plc’s respective standard conditions of contract.
Ein wichtiger Punkt beim Kauf des Geräts BT 1500 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie BT 1500 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für BT 1500 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von BT 1500 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über BT 1500 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon BT 1500 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von BT 1500 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit BT 1500. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei BT 1500 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
