DE
Carrier logo
Offizielle Bedienungsanleitung

Carrier Remote Controller (RG10L3)

76 Seiten·3.2 MB·Fernbedienung·PDF·ENFRITNLJA
Carrier Remote Controller (RG10L3)
Inhaltsverzeichnis 6 Abschnitte 空白页面 · 空白页面 · 空白页面 · 空白页面 · … AnzeigenAusblenden
Page 1 of the Carrier Remote Controller (RG10L3) user manual — REMOTE CONTROLLER
Seite 1 · Zum Vergrößern klicken
Seite 1

REMOTE CONTROLLER

OWNER’S MANUAL

Page 2 of the Carrier Remote Controller (RG10L3) user manual — Table of contents
Seite 2 · Zum Vergrößern klicken
Seite 2

Table of contents

Page 3 of the Carrier Remote Controller (RG10L3) user manual — SPECIAL NOTE
Seite 3 · Zum Vergrößern klicken
Seite 3
Carrier Remote Controller (RG10L3) — 空白页面 diagram (page 3)
Abb. 1
RG10L3(2HS)/BGEFU1,RG10L3(2HS)/BGEF 3.0V( Dry batteries R03/LR03×2) maximun 8m (vertical distance ) -5°C~60°C(23°F~140°F)
Carrier Remote Controller (RG10L3) — 空白页面 diagram (page 3)
Abb. 2

FIT BATTERIES

SELECT MODE SELECT TEMPERATURE

Carrier Remote Controller (RG10L3) — FIT BATTERIES diagram (page 3)
Abb. 3

NOT SURE WHAT A FUNCTION DOES? Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a detailed description of how to use your air conditioner.

SPECIAL NOTE

  • Button designs on your unit may differ slightly from the example shown. If the indoor unit does not have a particular function, pressing that function’s button on the remote control will have no effect. When there are wide differentces between “Remote controller Manual” and “USER’S MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.

• · •

Page 4 of the Carrier Remote Controller (RG10L3) user manual — TIPS FOR USING REMOTE CONTROL
Seite 4 · Zum Vergrößern klicken
Seite 4

Handling the Remote Controller

Inserting and Replacing Batteries

NOTES FOR USING REMOTE CONTROL

Your air conditioning unit may come with two batteries(some units). Put the batteries in the remote control before use.

The device could comply with the local national regulations. In Canada, it should comply with CAN ICES-3(B)/NMB-3(B). In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

1. Slide the back cover from the remote control downward, exposing the battery compartment. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment. Slide the battery cover back into place.

BATTERY NOTES

For optimum product performance: • Do not mix old and new batteries, or batteries of different types.

  • Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.

BATTERY DISPOSAL

Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

TIPS FOR USING REMOTE CONTROL

  • The remote control must be used within 8 meters of the unit. The unit will beep when remote signal is received. Curtains, other materials and direct sunlight can interfere with the infrared signal receiver. Remove batteries if the remote will not be used more than 2 months.
Show 5 more labels / short text on this page
• · • · • · • · •
Page 5 of the Carrier Remote Controller (RG10L3) user manual — RG10L3(2HS)/BGEFU1 , RG10L3(2HS)/BGEF
Seite 5 · Zum Vergrößern klicken
Seite 5

Buttons and Functions

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual.

ON/OFF Turns the unit on or off. MODE

Scrolls through operation modes as follows: AUTO COOL

TEMP

Increases temperate in 0.5°C (1°F) increments. Max. temperature is 30°C (86°F). NOTE: Press together & buttons at the same time for 3 seconds will alternate the temperature display between the °C & °F.

DRY HEAT FAN

BREEZE AWAY This feature avoids direct air flow blowing on the body and makes you feel indulging in silky coolness.

OK

Used to confirm the selected functions.

TIMER

SET Scrolls through operation

Set timer to turn unit on or off

ECO/GEAR

functions as follows:

Press this button to enter the energy efficient mode in a sequence of following: ECO GEAR(75%) GEAR(50%)

Sleep( ) Follow Me( ) AP mode

( ) clean( ) Active

mode ECO

The selected symbol will flash on the display area, press the OK button to confirm.

HUMIDITY

Adjust the room humidity during Dry operation in a range of 35%~85%. Press this button to increase the humidity in 5% increments. NOTE: After setting, the humidity settings will display on the screen.

TEMP

Decreases temperature in 0.5 C(1 F) increments.

O O Min. temperature is

O O 16 C(60 F).

LED

FAN SPEED

Turns indoor unit’s LED display and air conditioner buzzer on and off, which create a comfortable and quiet environment.

Selects fan speeds in the following order: AU

20% 60% 40% 80% 100%.

Press the TEMP or button to increase/decrease the fan speed in 1% increments. Enables unit to reach preset temperature in shortest possible time.

BOOST

SWING

Starts and stops the horizontal louver movement. Hold down for 2 seconds to initiate vertical louver auto swing feature.

Model:

RG10L3(2HS)/BGEFU1 , RG10L3(2HS)/BGEF

Show 5 more labels / short text on this page
Active clean( ) · Fresh( ) · Previous setting · Boost · Humidity
Page 6 of the Carrier Remote Controller (RG10L3) user manual — Remote Screen Indicators
Seite 6 · Zum Vergrößern klicken
Seite 6

Remote Screen Indicators

Information are displayed when the remote controller is power up.

Carrier Remote Controller (RG10L3) — Remote Screen Indicators diagram (page 6)
Abb. 4 · Remote Screen Indicators

Lights up when remote sends signal to indoor unit

Displays the set temperature by default, or fan speed or timer setting when using TIMER ON/OFF functions.

This fan speed can not be adjusted in AUTO or DRY mode.

35% -85% This display is blank when operating in FAN mode.

Page 7 of the Carrier Remote Controller (RG10L3) user manual — COOL Mode
Seite 7 · Zum Vergrößern klicken
Seite 7

How to Use Basic Functions

Basic operation

Carrier Remote Controller (RG10L3) — Basic operation diagram (page 7)
Abb. 5 · Basic operation
Carrier Remote Controller (RG10L3) — Basic operation diagram (page 7)
Abb. 6 · Basic operation

The operating temperature range for units is 16-30°C (60-86°F)/20-28 C(68-82 F)(Model dependent). You can increase or decrease the set temperature in 0.5°C (1°F) increments.

In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT operation based on the set temperature.

1. Press the MODE button to select AUTO .
2. Set your desired temperature using the TEMP or TEMP button.
3. Press the ON/OFF button to start the unit.
Carrier Remote Controller (RG10L3) — Basic operation diagram (page 7)
Abb. 7 · Basic operation

COOL Mode

1. Press the MODE button to select COOL mode. 2.

Set your desired temperature using the TEMP or TEMP button.

Press FAN button to select the fan speed in a range of AU-100%.

Press the ON/OFF button to start the unit.

Page 8 of the Carrier Remote Controller (RG10L3) user manual — HEAT Mode
Seite 8 · Zum Vergrößern klicken
Seite 8

DRY Mode (dehumidifying)

1. Press the MODE button to select DRY .
2. Set your desired temperature using the TEMP or TEMP button.
3. Press the ON/OFF button to start the unit.

FAN Mode

Press the MODE button to select FAN mode.

Press FAN button to select the fan speed in a range of AU-100%.

Press the ON/OFF button to start the unit.

HEAT Mode

1. Press the MODE button to select HEAT mode. 2.

Set your desired temperature using the TEMP or TEMP button.

Press FAN button to select the fan speed in a range of AU-100%.

Press the ON/OFF button to start the unit.

Humidity Boost · Humidity Boost · Humidity Boost

Page 9 of the Carrier Remote Controller (RG10L3) user manual — 2:00PM 3:00PM 4PM 5PM 6PM
Seite 9 · Zum Vergrößern klicken
Seite 9

Setting the TIMER

TIMER ON/OFF - Set the amount of time after which the unit will automatically turn on/off.

TIMER ON setting

Press TIMER button to initiate the ON time sequence. Press Temp. up or down button for for multiple times to set the desired time to turn on the unit.

Point remote to unit and wait 1sec, the TIMER ON will be activated.

TIMER

1 sec

MODE

ON/OFF

SLEEP

FAN

TIMER OFF TEM P

TIMER ON

SHOR T CUT

TIMER OFF setting

Press TIMER button to initiate the OFF time sequence. Point remote to unit and wait 1sec, the TIMER OFF will be activated.

Press Temp. up or down button for for multiple times to set the desired time to turn off the unit.

TIMER

1 sec

MODE

ON/OFF

SHOR T CUT

SLEEP

FAN

TIMER OFF TEM P

TIMER ON

NOTE: 1. When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24. 2. Cancel either function by setting its timer to 0.0h.

TIMER ON & OFF setting(example)

Keep in mind that the time periods you set for both functions refer to hours after the current time.

Carrier Remote Controller (RG10L3) — TIMER ON & OFF setting(example) diagram (page 9)
Abb. 8 · TIMER ON & OFF setting(example)

Example: If current timer is 1:00PM, to set the timer as above steps, the unit will turn on 2.5h later (3:30PM) and turn off at 6:00PM.

2:00PM 3:00PM 4PM 5PM 6PM

3:30PM

Carrier Remote Controller (RG10L3) — 2:00PM 3:00PM 4PM 5PM 6PM diagram (page 9)
Abb. 9

Current time 1PM

Page 10 of the Carrier Remote Controller (RG10L3) user manual — LED LED
Seite 10 · Zum Vergrößern klicken
Seite 10
Carrier Remote Controller (RG10L3) — 空白页面 diagram (page 10)
Abb. 10

The horizontal louver will swing up and down automatically when pressing Swing button. Press again to make it stop.

Keep pressing this button more than 2 seconds, the vertical louver swing function is activated. (Model dependent)

Airflow direction

If continue to press the SWING button, five different airflow directions can be set. The louver can be move at a certain range each time you press the button. Press the button until the direction you prefer is reached.

Swing

Carrier Remote Controller (RG10L3) — Swing diagram (page 10)
Abb. 11 · Swing

5s

Press LED button Press this button more than 5 seconds(some units)

LED LED

Keep pressing this button more than 5 seconds, the indoor unit will display the actual room temperature. Press more than 5 seconds again will revert back to display the setting temperature.

Press this button to turn on and turn off the display on the indoor unit.

Carrier Remote Controller (RG10L3) — LED LED diagram (page 10)
Abb. 12

Press together Mode button and “ ” button at the same time more than 3 seconds to activate this function, and the remote controller displays "F2".When setting the panel status, press the “ ” or “ ” buttons of the remote controller to control the rise or fall of the grille, and press any other button to exit the setting.

Page 11 of the Carrier Remote Controller (RG10L3) user manual — BREEZE AWAY
Seite 11 · Zum Vergrößern klicken
Seite 11

ECO/GEAR function

Press X-ECO button to enter the energy efficient mode in a sequence of following: ECO GEAR(75%) GEAR(50%) Previous setting mode ECO

ECO operation:

Under cooling mode, press this button, the remote controller will adjust the temperature automatically to 24 C/75 F, fan speed of Auto to save energy (only when the set temperature is less than 24 C/75 F). If the set temperature is above 24 C/75 F, press the ECO button, the fan speed will change to Auto, the set temperature will remain unchanged.

O

O

O O O

O

O

O

O O

GEAR operation: Press the ECO/GEAR button to enter the GEAR operation as following: 75%(up to 75% electrial energy consumption)

50%(up to 50% electrial energy consumption)

Previous setting mode.

Under GEAR operation, the display on the remote controller will alternage between electical energy consumption and set temperature.

BREEZE AWAY

This feature avoids direct air flow blowing on the body and makes you feel indulging in silky coolness.

NTOE: This feature is available under cool,Fan and Dry mode only.

Press this button

Page 12 of the Carrier Remote Controller (RG10L3) user manual — Boost
Seite 12 · Zum Vergrößern klicken
Seite 12

Silence function

2s Keep pressing Fan button for more than 2 seconds to activate/disable Silence function(some units).

Fan

Due to low frequency operation of compressor, it may result in insufficient cooling and heating capacity. Press ON/OFF, Mode, Sleep, Turbo or Clean button while operating will cancel silence function.

FP function

O Press this button 2 times during one second under HEAT Mode and setting temperature of 16 C/60 F or 20 C/68 F(for model RG10L10(2HS)/BGEF only).

The unit will operate at high fan speed (while compressor on) with temperature automatically set to 8 C/46 F.

Press this button 2 times during one second under HEAT Mode and setting temperature of 16 C/60 F or 20 C/68 F(for model RG10L10(2HS)/BGEF) to activate FP function.Press On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function.

LOCK function

5s 5s

+

Press together Boost button and Humidity button at the same time more than 5 seconds to activate Lock function. All buttons will not response except pressing these two buttons for two seconds again to disable locking.

BOOST Function

When you select Boost feature in COOL mode, the unit will blow cool air with strongest wind setting to jump-start the cooling process.

Boost

When you select Boost feature in HEAT mode, for units with Electric heat elements, the Electric HEATER will activate and jump-start the heating process.

Boost · Humidity · Press Boost button

Page 13 of the Carrier Remote Controller (RG10L3) user manual — ,
Seite 13 · Zum Vergrößern klicken
Seite 13
Carrier Remote Controller (RG10L3) — 空白页面 diagram (page 13)
Abb. 13

Press the SET button to enter the function setting, then press SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area, press the OK button to confirm.

To cancel the selected function, just perform the same procedures as above.

Press the SET button to scroll through operation functions as follows:

* *

Active clean ( ) Fresh ( ) Sleep( ) Follow Me( ) AP mode ( ) Active clean ( ) [ ]: Model dependent

*

Active clean function( ) (some units) :

Follow me function( ) :

The Active Clean Technology washes away dust, mold, and grease that may cause odors when it adheres to the heat exchanger by automatically freezing and then rapidly thawing the frost. When this function is turned on, the indoor unit display window appears “CL”, after 20 to 45 minutes, the unit will turn off automatically and cancel CLEAN function.

The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3 minutes interval. When using AUTO, COOL or HEAT modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself) will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.

FRESH function( ) (some units) :

When the FRESH function is initiated, the Ionizer/Plasma Dust Collector(depending on models) is energized and will help to remove pollen and impurities from the air

,

,

,

,

If the memory feature is activated, On displays for 3 seconds on the screen.

Sleep function( ) :

, If the memory feature is stopped, Of displays for 3 seconds on the screen. While the memory feature is activated, press the ON/OFF button, shift the mode or power failure will not cancel the Follow me function.

,

,

,

The SLEEP function is used to decrease energy use while you sleep (and don t need the same temperature settings to stay comfortable). This function can only be activated via remote control.

,, ,

,, ,,

For the detail, see sleep operation in USER S MANUAL. ,

AP function( )(some units) :

Choose AP mode to do wireless network configuration. For some units, it doesn’t work by pressing the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.

in FAN or DRY mode.

,

,

Page 14 of the Carrier Remote Controller (RG10L3) user manual — 空白页面
Seite 14 · Zum Vergrößern klicken
Seite 14
Page 14 of the Carrier Remote Controller (RG10L3) user manual — 空白页面
Page 15 of the Carrier Remote Controller (RG10L3) user manual — Table of contents
Seite 15 · Zum Vergrößern klicken
Seite 15

Table of contents

Frage zu Carrier Remote Controller (RG10L3) stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Carrier Remote Controller (RG10L3)

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Carrier Remote Controller (RG10L3) PDF-Anleitung

76 Seiten·3.2 MB·Fernbedienung·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…