Benutzeranleitung / Produktwartung HL-1110 des Produzenten Brother
Zur Seite of 73
User’s Guide Brother Laser Printer HL-1110 HL-1111 For visually-impaired users You can read this manual with Scre en Reader ‘text-to-speech’ software. You must set up the hardware and install the dr iver before you can use the ma chine. Please use the Quick Setup Guide to set up the machin e.
i Brother numbers IMPORTANT For technical and operational help, you must call the country where you boug ht the machine. Calls must be made from within that country. Register your product Please complete the Brother Warranty Registration or, for your convenience and most efficient way to register your new product, register on-line at http://www.
ii User’s Guides and where to find them? Which manual? What's in it? Where is it? Windows users Macintosh users Product Safety Guide Read this Guide first. Please read the Safety Instructions before you set up your machine. See this Guide for trademarks and legal limitations.
iii Using the documentation Thank you for buying a Brother ma chine! Reading the doc umentatio n will help you make the most of your machine. Symbols and conventions us ed in the documentation The following symbols and conventions ar e used throughout the do cumentation.
iv Table of Contents 1 Printing Methods 1 About this Machine ............... ................ ................... ................. ................ ................... ....... ................ ....... 1 Machine overview .............. ...............
v A Troubleshooting and other information 45 Consumable items ................ ................ ................... ................. ................ ................... ........ ........... ......... 45 Toner Setting . ................ .............
1 1 1 About this Machine 1 Machine overview 1 1 Top cover 2 Control panel 3 Face-down output tray support flap (support flap) 4 Paper tray 5 USB port NOTE For details about how the LEDs show th e machine’s status, see LEDs (Light Emitting Diodes) o n page 36.
Printing Methods 2 1 Acceptable paper 1 Print quality may vary according to the type of paper you are using. For best results, follow the instructions below: DO NOT put different types of paper in the paper tray at the same time because it may cause paper jams or misfeeds.
Printing Methods 3 1 2-sided printing 1 The supplied printer drivers all enabl e 2-sided printing. For more information abo ut how to choose the settings, see 2-sided / Booklet on page 10 for W indows ® and 2-sided Printing o n page 33 for Macintosh.
Printing Methods 4 1 Manual 2-sided printing 1 If you are using the Macintosh Printer Driver, see Manual 2-sided Printing on page 33. Manual 2-sided printing with the Windo ws ® printer driver 1 a Choose the following settings from ea ch drop-down list of the printer driver.
5 2 2 Printer driver 2 A printer driver is software that translates data from the fo rmat used by a computer to the f ormat that a particular printer needs.
Driver and Softwa re 6 2 • If your application software does n ot support your custom paper size, choose the next largest pape r size. • Then adjust the print area by changin g the right and left margins in your application software.
Driver and Softwa re 7 2 Windows ® 2 Accessing the printer driver settings 2 a (For Windows ® XP and Windows Server ® 2003) Click Start , and then Printers and Faxes . (For Windows Vista ® and Windows Server ® 2008) Click the ( Start ) button, Contro l Panel , Hardware and So und , and then Printers .
Driver and Softwa re 8 2 Basic tab 2 You can also change the Page Layout settings by clicking the illustration on the left side of the Ba sic tab. a Choose the Paper Size , Orientation , Copies , Media Type , Print Quality and Print Settings (1) . b Choose Multiple Page and 2 -sided / Booklet (2).
Driver and Softwa re 9 2 Orientation 2 Orientation selects the position of how you r document will be printed ( Portrait or Landscape ). Copies 2 The copies selection sets the number of copies that will be p rinted.
Driver and Softwa re 10 2 Print Settings 2 You can change the print settings as follows: Graphics This is the best mode for printing documents that contain graphics. Text This is the best mode for printing text d ocuments. Manual You can change the se ttings manually by choosing Manua l and clicking the Manual Settings.
Driver and Softwa re 11 2 • 2-sided Type There are four types of 2-sided binding d irections available for each orientation. • Binding Offset When you check Binding Offset , you can also specify the offset for binding in inches o r millimetres.
Driver and Softwa re 12 2 • 2-sided Type There are two types of 2-sided b inding dire ctions available for each orientatio n. • Booklet Printing Method When Divide into Sets is selected: This opti.
Driver and Softwa re 13 2 1 Page List Area The Page List Area displays the page numbers for the actual pages that will be printed. If you chose a page in this list, a preview of the print results for the page will be displaye d in the Preview Area. If you do not want to print a page , clear the check mark.
Driver and Softwa re 14 2 Scaling 2 You can change the print image scaling. Reverse Print 2 Check Reverse Print to reverse the dat a from up to down. Use Watermark 2 You can put a lo go or text into your document as a wa termark. You can choose one of the preset Watermarks, or you can use a bitmap file that you have create d.
Driver and Softwa re 15 2 Select Watermark Choose a watermark to use . To make an original watermark, click the Add button to add the watermark settings and then cho ose Use Text or Use Bitmap File in Watermark Style . • Title Enter a suitable title into the field.
Driver and Softwa re 16 2 Header-Footer Print 2 When this feature is enabled, it will print the d ate an d time on your document from your computer’s syste m clock and the PC login user name or the text you entered. By clicking Settings , you can customize the information.
Driver and Softwa re 17 2 Watermark Lock Lock the current settings of the Watermark optio n to prevent changes being ma de. Header-Footer Print Lock Lock the current settings of the Header-F oot er Print option to prevent changes being made.
Driver and Softwa re 18 2 NOTE This operation will decrease the temperatu re of the machine's fusing process. Improve Toner Fixing If you choose this setting, t he toner fixing capabilities may be imp roved. NOTE This operation will increase the temperat ure of the ma chine's fusing process.
Driver and Softwa re 19 2 Print Profiles tab 2 Print Profiles are editable presets de signed to give you quick access to frequently used pr inting confi guratio ns.
Driver and Softwa re 20 2 Delete Profile 2 The Delete Profile dialog box appears by clicking Delete Profile . You can delete any of the profiles you have added. a Choose your profile from the print profile list box. b Click Delete . c Click Yes . d The selected profile will be deleted.
Driver and Softwa re 21 2 Device Settings tab 2 NOTE To access the Device Settings ta b, see Accessing the printer driver settings on pag e 7. You can auto detect the serial number in th e Device Settings ta b as follows. Serial No. (1) By clicking Auto Detect (2), the printer driver will p robe the mach ine and display its serial number.
Driver and Softwa re 22 2 Support 2 Click Support... in the Printing Preferences dialog box. Brother Solutions Center (1) The Brother Solutions Center (http://solut ions.
Driver and Softwa re 23 2 Original Supplies Website (2) You can visit our website for orig inal/genui ne Brother supplies by clicking this bu tton. Brother CreativeCenter (3) You can visit our website for free a nd easy online solutions for business and home users by clicking this button.
Driver and Softwa re 24 2 Status Monitor 2 The Status Monitor utility is a con figurable software tool for monitoring the status of one or more devices, allowing you to get immediate notification of erro r messages.
Driver and Softwa re 25 2 Monitoring the machine’s status 2 The Status Monitor icon will change co lour depending on the machine status. A green icon indicates the normal stand-by condition. A yellow icon indicates a warning. A red icon indicates a printing error has occurred.
Driver and Softwa re 26 2 Macintosh 2 Features in the printer driver (Macintosh) 2 This machine supports Mac OS X v10.6.8, 10 .7.x, 10.8.x. NOTE • The screens in this section are from OS X v10.7. Th e screens on your Macint osh will vary depending on your operating system version.
Driver and Softwa re 27 2 b From an application such as TextEdit, click File , then Print to start printing. (For Mac OS X v10.6.8) For more page setup options, click the disclo sure triangle beside the Printer po p-up menu. NOTE You can save the current se ttings as a preset by choosing Save As from the Presets pop-up menu.
Driver and Softwa re 28 2 (For OS X v10.7.x and v10.8.x) For more page setup options, click the Sh ow Details button. NOTE You can save th e current settings as a preset by choosing Save Current Settings as Preset.
Driver and Softwa re 29 2 Choosing printing options 2 To control special printing features, choose Print Settings from the Prin t dialog box. For the details of available options, see the follow ing descriptions of each option.
Driver and Softwa re 30 2 Layout 2 Pages per Sheet The Pages per Sheet selection ca n reduce the image size of a page by allowing multiple pag es to be printed on one sheet of paper. Layout Direction When you specify the pages per sheet, you can also specify the direction of the layout.
Driver and Softwa re 31 2 Print Settings 2 You can change settings by choosing a setting in the Print Settings list: Media Type You can change the me dia type to one of the following: • Plain Pa.
Driver and Softwa re 32 2 Advanced print settings When you click the triangle mark ( c ) beside Ad vanced , the advanced print settings appear. Toner Save Mode You can conserve toner use with this feature. When you set T oner Save Mode to on, print app ears lighter.
Driver and Softwa re 33 2 • Improve Toner Fixing If you choose this setting, the t oner fixing capabilities may be improved. NOTE This operation will increase the temperat ure of the ma chine's fusing process. Density Adjustment Increase or decrease the print density.
Driver and Softwa re 34 2 Status Monitor 2 The Status Monitor utility is a configurable software tool for moni toring the status of the machine, letting you see error messages at pre-set update inte rvals.
Driver and Softwa re 35 2 Software 2 Remote Printer Console (Windows ® only) 2 Remote Printer Console is soft ware to change many of the printer settings independently of your application. For example, you can change the settings for printer margin and so on.
36 3 3 Control panel 3 LEDs (Light Em itting Diodes) 3 This section refers to two LEDs and one key on the control panel. 1 Power On/Off You can turn the ma chine on and off. Press and hold down to turn the ma chine on. Press and hold down to turn the ma chine off.
General Informatio n 37 3 LEDs Machine St atus Sleep The machine is in Sleep Mode (Power Save mode) . While the machine is in Sleep Mode, the Ready LED ( ) is dimmed, but the machine can still receive data. Receiving a prin t job will automatically wake up the machine to start printing.
General Informatio n 38 3 Toner Low The toner cartridge will need to be replaced soon. Buy a new toner cart ridge and have it ready for when Replace Toner is indicated.
General Informatio n 39 3 Drum ! The corona wire n eeds to be cleane d. See Cleani ng the corona wire on Improving the print quality . The Error LED ( ) will blink 3 times and turn off for 1 second.
General Informatio n 40 3 Service call indications 3 If there is an error that cannot be cleared by the user, th e machine will show that a service call is needed by lighting up all the LE Ds as shown below. If you see the service call indication shown above, turn off the machine, and then turn it back on and try to print again.
General Informatio n 41 3 Power On/Off key 3 Power On/Off key has the following functions: Power Off Make sure that the machine is in the Ready mode, then hold down for about 2 seconds. All the LEDs turn off when you enable the Power Off mo de. For details about Power Off mode, see Powe r Off mode on page 44.
General Informatio n 42 3 Print a Printer Settings page 3 You can print the current settings using the co ntrol panel button or printer driver. Using the Power On/Off key 3 a Make sure that the top cover is closed an d the power cord is plugged in. b Turn on the machine and wait until the machine is in Ready mode.
General Informatio n 43 3 Ecology features 3 Toner Save 3 You can save toner using this feature. When you set Toner Save to on, prints appear ligh ter.
General Informatio n 44 3 Power Off mode 3 Power Off mode is the lowest p ower consumption mode, wh ich achieves a power co nsumption of less than 0.28 W. When you enable the Au to Power Off feature, th e machine will automatically go int o the Power Off mode after a certain period of time.
45 A A Consumable items A The drum unit and toner cartr idge are two separate consumables. Make sure both are installed as an assembly. For more information on how to replace the consumab le items, se.
Troubleshooting and other informati on 46 A Toner Setting A The printing operation varies depend ing on the machine setting: Default setting (Stop mode) The machine will stop prin ting until you replace the t oner cartridge wit h a new one when the LEDs indicate Replace Toner .
Troubleshooting and other informati on 47 A Identifying your problem A First, check the following. The machine's power cord is connected correctly and the machine is turned on. All of the protective parts have been removed. Paper is inserted correctly in the paper tray.
Troubleshooting and other informati on 48 A Error messages in the Status Monitor A The most common error and maintenance messages are shown belo w. If you need more help, the Brother Solution s Center offers the latest FAQs and troublesho oting tips: Visit us at http://solutions.
Troubleshooting and other informati on 49 A Improving the print quality A NOTE Brother does not recommend the use of cartrid ges ot her than genuine Bro ther Original cartridges or the refilling of used cartridges with toner from other sources. If you are having problems with print resu lts, check the following: 1 The machine's environment.
Troubleshooting and other informati on 50 A 4 Replace a toner cartridge or a drum unit. For more information on how to replace the consumable items, see the instru ctions included with the drum unit for replacing the drum unit or see the instructions listed on the box of the toner cartridge for replacing the toner cartridge.
Troubleshooting and other informati on 51 A Turn the drum unit gear by hand while looking at the surfa ce of the drum roller (1). Wipe the surface of the drum gently with a dry cotton swab until the dust or glue on the surface comes off.
Troubleshooting and other informati on 52 A 6 Check th e printer driv er settings. Try changing the Print Settings in Basic tab. If the paper is curled or the toner is not fixed well on th e paper, you can adjust these settings in Improve Print Output .
Troubleshooting and other informati on 53 A Paper jams A If a paper jam occurs inside the machine or the paper tray, the Error LED ( ) will blink twice. a Leave the machine turned on for 15 minu tes for the product to cool down before you tou ch the internal parts of the product.
Troubleshooting and other informati on 54 A d Slowly take out the dru m unit and toner cartridge assembly. The jammed paper may be pulle d out with the drum unit and toner cartr idge assembly, or this may release the p aper so you can pull it out from inside of the machine.
Troubleshooting and other informati on 55 A e Push down the lock lever and take the toner cartridge out of the drum unit. Remove the jammed paper if there is any inside the drum u nit. f Put the toner cartridge back into the drum unit until you hear it lock into place.
Troubleshooting and other informati on 56 A i Make sure that the paper is below the protruding section of the rear guide. Slide the paper guides to fit the paper size. Make sure that the guide s are firmly in the slots. NOTE If you turn off the machine during pape r jam, the machine will print incomplete da ta from your computer.
Troubleshooting and other informati on 57 A If you are having difficulty with your machine A IMPORTANT • For technical help, you must call the cou ntry where you bought the machine. Calls must be made from within that country. • If you think there is a problem with your mach i ne, check the chart below and follo w the troubleshooting tips.
Troubleshooting and other informati on 58 A The machine is not printing or prints unexpectedly. Press and hold for a bout 2 seconds until all the L EDs light up and then release it. The machine will cancel the print job and clear it from the memory . The printout may be incomplete.
Troubleshooting and other informati on 59 A Cleaning and Checking the machine A Clean the outside and inside of the machine regularly with a dry, lint-free cloth. When you replace the toner cartridge or the drum unit, make sure that you clean the inside of the machine.
Troubleshooting and other informati on 60 A Machine Information A Default settings A The machine has two levels of default settings; the default settings have been set at the fa ctory before shipment. Factory Reset Settings Reset NOTE • You cannot modify the preset default settings.
61 B B General B Specifications B Model HL-1110 (for Australia) HL-1110 (for other coun tries) HL-1111 (for India) Printer Type Laser Print Method Electrophotographic Laser Pr inter Memory Capacity Standard 1 MB Power Source 220 - 240 V AC 50/60Hz Power Consumption 1 (Average) Peak Approx.
Specifications 62 B 1 Measured when the machine is connecte d to the USB interface. 2 Power consumption varies slightly dependi ng on the usage environment or part wear. 3 Measured according to IEC 62301 Edition 2.0. 4 The machine can also be connected to a comput er that has a USB 1.
Specifications 63 B Print media B Model HL-1110 (for Australia) HL-1110 (for other countries) HL-1111 (for India) Paper Input Paper Tray Paper Type Plain paper, Recycled pa per Paper Size A4, Le tter,.
Specifications 64 B Important information fo r choosing your paper B The information in this section will help you choose paper to use with this machine. NOTE If you use paper that is not reco mmended, a paper jam or misfeed may o ccur in the machine.
Specifications 65 B Printer B 1 The print speed may change depending on the type of do cument you print. 2 From Ready mode Model HL-1110 (for Australia) HL-1110 (for other count ries) HL-1111 (for Ind.
Index 66 C C Numerics 2-sided / Booklet ........ ................ ................ ............... 10 2-sided pr inting ... ................ ................ ................. ....... 3 A Administrator ....................... ................ ........
For Australia Only: Support - For technical support of your Brother Product ot her than what you can resolve through the User' s Guide, please visit our Web Site or Solut i ons Web Site (see below ) to find an answer to FAQs/Troubleshooting, lo cating Drivers & Software.
Ein wichtiger Punkt beim Kauf des Geräts Brother HL-1110 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Brother HL-1110 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Brother HL-1110 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Brother HL-1110 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Brother HL-1110 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Brother HL-1110 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Brother HL-1110 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Brother HL-1110. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Brother HL-1110 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
