

NUMBER One IN SOUND NUMBER One IN SOUND


Set the dip switch to your needs.
Dip switch 1 on/down = attenuate the speaker outputs by 10 dB. Dip switch 2 = n.c. (not connected).
power supply on page 8.
Turn down speaker and headphone volume.
Make sure that the Power switch on the rear is set to Off
Switch the on Control One by pressing the Power button.
(Off = out position / ON = in position).
Choose speaker output A or B.
an appropriate mains socket outlet.
Select a monitoring mode: stereo, mono or L/R swapped.
Connect your speakers to the Speaker Outputs.
Set the volumes and the crossfeed to taste.
You can connect two pairs of active stereo speakers – A and B. The A Speaker Output has a dedicated Sub Output for an active subwoofer.
Playback your music from the Line Inputs.
Connect your headphone to the headphone output.
Connect your analog sources to the Line Inputs.
sum of Line Input 1 and 2.
Connect the Line Out to your analog audio device.
The Line Out plays back the signal from Line Input 1, Line Input 2 or Line Input 1 and 2 summed – depending on the Line input switch. The level is unity gain, thus independent of the volume control.





Analog inputs & outputs; 6.35 mm (1/4") TRS Jack (balanced), RCA
Headphones Output; 6.35 mm (1/4") TRS Jack
Input gain (max.) +22.5 dBu
Wiring Tip = Left, Ring = Right, Sleeve = GND
Source impedance 20 Ω
Frequency range (-3 dB) 10 Hz - 200 kHz
Noise (A-weighted, 600 Ω) -97 dBu
THD + N (0 dBu, 10 Hz – 22 kHz, 600 Ω) 0,002 %
THD + N (0 dBu, 10 Hz – 22 kHz, 32 Ω) 0,013 %
Max output power (600 Ω) 2 x 190 mW
Sub Output low filter none (full range)
Max output power (250 Ω) 2 x 330 mW
Max output power (47 Ω) 2 x 400 mW
Fade-out attenuation (600 Ω) -99 dB
Frequency range (-3dB) 10 Hz - 200 kHz
Crosstalk (1 kHz, 600 Ω) -75 dB
Dynamic range 121 dB
Dynamic range 117 dB
Noise (A-weighted, 600 Ω load) -99 dBu
Total harmonic distortion (0 dBu, 10 Hz – 22 kHz) 0.002 %
Crosstalk (1 kHz) < 75 dB
Fade-out attenuation -93 dB

Operating voltage for analog audio +/- 17 V
W x H x D (width x height incl. feet x depth) 210 x 49,6 x 220 mm / 8,23 x 1,95 x 8,66 inch
Operating voltage for headphone amplifier +/- 19 V
Unit weight 1,5 kg / 3, lb
Operating voltage for relays +12 V
Shipping weight (incl. packaging) 2 kg / 4,4 lb
AC/DC switching adapter Mean Well GE18/12-SC
DC plug (+) pin 2.1mm; (-) outside ring 5.5mm
Input 100 - 240 V AC; 50 - 60 Hz; 0.7 A
Output 12 V DC; 1.5 A
Reference: 0 dBu = 0,775V. All specifications are subject to change without notice.
Internal Power Supply · Dimensions & Weight · External Power Supply

Fire warning Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire.
Before starting up the device:
Lightning Before thunderstorms or other severe weather, disconnect the power supply from the mains socket outlet; do not do this during a storm in order to avoid life threatening light- ning strikes. Similarly, disconnect all the power connections of other devices, antenna and phone/network cables which may be interconnected so that no damage results from such secondary connections.
If you notice any abnormality When one of the following problems occur, immediately turn off the power switch and dis- connect the power supply from the mains socket outlet. Then have the device inspected by a qualified professional.
External power supply/Power cord Do not place the power cord near heat sources such as heaters or radiators and do not ex- cessively bend or otherwise damage the cord, do not place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. Only use the voltage indicated on the device. Only use the supplied power supply. If you intend to use the device in an area other than in the one you purchased it, the in- cluded power supply may not be compatible. In this case please contact your dealer.
Do not open This device contains no user-serviceable parts. Do not open the device or attempt to disas- semble the internal parts or modify them in any way. If it should appear to be malfunction- ing, turn off the power immediately, unplug the power supply from the mains socket outlet and have it inspected by a qualified professional.
External power supply/Power cord When removing the power cord from the device or the power supply from a mains socket outlet, always pull on the plug/power supply itself and not the cord. Pulling the cord may damage it. Unplug the power supply from the mains socket outlet when the device is not used for a while.
Water warning Do not expose the device to rain, or use it near water or in damp or wet conditions, or place anything on it (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the device, turn off the power immedi- ately and unplug the power supply from the mains socket outlet. Then have the device in- spected by a qualified professional. Never insert or remove the power supply with wet hands.
Location Do not place the device in an unstable position where it might accidentally fall over. Do not block the vents. This device has ventilation holes to prevent the internal tempera- ture from rising too high. In particular, do not place the device on its side or upside down. Inadequate ventilation can result in overheating, possibly causing damage to the device or even fire.

Cleaning Disconnect the power cord from the device before cleaning. Do not use any solvents, as these can damage the chassis finish. Use a dry cloth, if neces- sary, with an acid-free cleaning oil.
Do not place the device in a location where it may come into contact with corrosive gases or salty air. This may result in malfunction. Before moving the device, remove all connected cables. When setting up the device, make sure that the mains socket outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the power supply from the mains socket outlet. Even when the power switch is turned off, electricity is still flowing to the product at a minimum rate. When you are not using the device for a long time, make sure to unplug the power supply from the wall mains socket outlet.
Disclaimer Windows® is a registered trademark of Microsoft® Corporation in the United States and other countries. Apple, Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries. The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. SPL and the SPL Logo are registered trademarks of SPL electronics GmbH. SPL cannot be held responsible for damage caused by improper use or modification of the device or data that is lost or destroyed.
Connections Before connecting the device to other devices, power down all devices. Before power on or off the devices, set all volume levels to minimum. Only use appropriate cables to connect the device with other devices. Make sure that the cables you use are intact and comply with the electrical specifications of the connection. Other connections can lead to health risks and damage the equipment.
Handling Operate the controls and switches only as described in the manual. Incorrect adjustments outside safe parameters can lead to damage. Never use excessive force on the switches or controls. Do not insert your fingers or hands in any gaps or openings of the device. Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any gaps or openings of the device. If this happens, power down immediately and unplug the power supply from the mains socket outlet. Then have the device inspected by a qualified profes- sional. Do not expose the device to excessive dust or vibrations or extreme cold or heat (such as direct sunlight, near a heater or in a car during the day) to prevent the possibility of causing damage to the housing, the internal components or unstable operation. If the ambient temperature of the device suddenly changes, condensation can occur (if for example the device is relocated or is affected by a heater or air conditioning). Using the device while condensation is present may result in malfunction. Do not power on the device for a few hours until the condensation is gone. Only then it is safe to power on.
At the end of its operating life, this product must not be disposed with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The wheelie bin symbol on the product, user manual and packaging indicates that. For proper treatment, recovery and recycling of old products, please take them to applica- ble collection points in accordance with your national legislation and the Directives 2012/19/EU. The materials can be reused in accordance with their markings. Through reuse, recycling of raw materials, or other forms of recycling of old products, you are making an important contribution to the protection of our environment. Your local administrative office can advise you of the responsible waste disposal point. This directive only applies to countries inside the EU. If you wish to discard devices outside the EU, please contact your local authorities or dealer and ask for the correct method of disposal. WEEE-Reg-No.: 973 349 88

Installation

NUMBER One IN SOUND NUMBER One IN SOUND
In dieser Anleitung genannte Seiten – Hersteller, Support und Downloads.
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.