DE
Digitus logo
Offizielle Bedienungsanleitung

Digitus 19 Automatic Transfer Switch (DN-95639)

55 Seiten·522 KB·Switch·PDF·ENNLJA
Digitus 19 Automatic Transfer Switch (DN-95639)
Inhaltsverzeichnis 2 Abschnitte DN-95639_QIG_rev1-0_EN · DN-95639_QIG_rev1-0_DE AnzeigenAusblenden
Page 1 of the Digitus 19 Automatic Transfer Switch (DN-95639) user manual — Automatic Transfer Switch
Seite 1 · Zum Vergrößern klicken
Seite 1

Automatic Transfer Switch

Quick Installation Guide

DN-95639

Page 2 of the Digitus 19 Automatic Transfer Switch (DN-95639) user manual — Safety and Grounding:
Seite 2 · Zum Vergrößern klicken
Seite 2

Safety and Grounding:

Read the following information before installing or operating your DIGITUS Automatic Transfer Switch:

  • This ATS is intended for indoor use only.
  • This ATS must not be operated one behind the other!
  • Operation only in dry and closed rooms.
  • This ATS may not be operated covered. Always ensure free accessibility.
  • The maximum power stated on the rating plate must not be exceeded.
  • Plug this ATS into a three-wire, grounded power outlet only. The power outlet must be connected to appropriate branch circuit/ mains protection (fuse or circuit breaker). Connection to any other type of power outlet may result in a shock hazard.
  • Use only the supplied brackets of mounting.
  • Check that the power cord, plug, and socket are in good condition.
  • Voltage free only when the power plug is unplugged.
  • Disconnect the PUD from the power outlet before you install or connect equipment to reduce the risk of electric shock when you cannot verify grounding. Reconnect the ATS to the power outlet only after you make all connections.
  • Operation under unfavorable environmental conditions must be avoided. (Humidity over 80% relative, wet, ambient temperatures above 50 ° C, solvents, flammable gases, dust, vapors).
  • If external damage to this ATS is detected, do not operate this ATS. Take this ATS immediately out of service if external damage is detected.
  • Do not pour liquids over the power strip. There is a high risk of fire or lifethreatening electric shock.
  • When opening the power strip, live parts can be exposed. There is a risk of electric shock. The power strip may only be opened by a specialist.
Page 3 of the Digitus 19 Automatic Transfer Switch (DN-95639) user manual — Product Schematic
Seite 3 · Zum Vergrößern klicken
Seite 3

Product Schematic

Digitus 19 Automatic Transfer Switch (DN-95639) — Product Schematic diagram (page 3)
Abb. 1 · Product Schematic
① Alarmthe port of buzz and flesh, used to connect to external annunciator
② RS232Serial communication port, connect the device to local PC
③ LED screendisplay the current; voltage; IP address and hardware version
④ ResetRest button
⑤ Preferenceto select the preferred power source

⑥ Input indicator of source B

⑦ Output indicator of source B

⑧ RUNOperation indicator
⑨ NETEthernet Port
⑩ Press to select dataTo view power date and information

⑪ Preference indicator of source A

⑫ Preference indicator of source B

⑬ Input indicator of source A

⑭ Output indicator of source A

Page 4 of the Digitus 19 Automatic Transfer Switch (DN-95639) user manual — DN-95639_QIG_rev1-0_EN
Seite 4 · Zum Vergrößern klicken
Seite 4
1. One serial cable 2. One network cable (only intelligent ATS) 3. Four Ø 6 x 16 mm cross bolt 4. One user manual and CD 5. Optional accessories 5.1. Circuit breaker (either circuit breaker or surge protection) 5.2. Surge protection module (either surge protection or circuit breaker) Mounting Method

Horizontal rack mounting Hardware Introduction

1. Self-checking when power on The buzz beep once when power on, the LED indicator always lights on, digital screen display load current after self-checking.
2. Operation status viewing Through "press to select date" button, user can view the voltage; IP address (only intelligent type) and device version number.

3. Select the preferred power source. Use Preferred button to select the primary power source, three options users can have: set the source A as the preferred power source; set the source B as the preferred power source; or user can leave this open. The corresponding indicator will always light on if a choice was made. If not, the two indicators will stay the off status. Please be noted that the intelligent ATS is with the Lock function, if user cannot do the setting above, please log on to the Web web interface to unlock.

4. Reset operation. If want to manual-reset ATS, Press the Reset button to reset the rack PDU without affecting the outlet status.
5. Restore to factory settings Press and hold the “press to select data” button for 6 seconds, the LED screen will display “IP” when release, then press the Reset to restore to the default IP 192.168.1.163 and default Username and password.
6. Serial connection Use the supplied serial cable, insert the RJ45 connector to RS232 communication port and connect the other end to the serial port of local PC.

Accessories list

Page 5 of the Digitus 19 Automatic Transfer Switch (DN-95639) user manual — DN-95639_QIG_rev1-0_EN
Seite 5 · Zum Vergrößern klicken
Seite 5
7. External connection annunciator Use the supplied terminal to connect the annunciator, the terminal allows maximum voltage of 50VDC and load current of 5A.
8. Ethernet connection (only intelligent type) Use supplied network cable, connect one side to the NET port of device and the other end to network. Software user guide
  • 1. Software configuration 1.1. Device default settings Device default IP: 192.168.1.163 Default username: admin Default password: admin Note: Both the default username and password are in lowercase, user cannot log on to the interface with uppercase. 1.2. Device configuration when first log in
  • Connect the device to PC directly.
  • Rework the network configuration of PC, make sure the changed PC IP address and the IP of the ATS is in the same segment, the default of the IP address is 192.168.1.163; Default subnet Mask is 255.255.255.0; Default gateway is 192.168.1.1. For instance, change the network configuration of the PC to IP: 192.168.1.145; log on to the management interface.
  • Click the "Network Config" on the left menu to rework the IP of the ATS, see the below interface, change the IP address of the ATS and make sure it is in the same segment where the PC IP is.
  • Restore the PC network configuration, Sign into the management interface with the changed IP address of ATS.
Digitus 19 Automatic Transfer Switch (DN-95639) — DN-95639_QIG_rev1-0_EN diagram (page 5)
Abb. 2 · DN-95639_QIG_rev1-0_EN
Digitus 19 Automatic Transfer Switch (DN-95639) — DN-95639_QIG_rev1-0_EN diagram (page 5)
Abb. 3 · DN-95639_QIG_rev1-0_EN
Page 6 of the Digitus 19 Automatic Transfer Switch (DN-95639) user manual — DN-95639_QIG_rev1-0_EN
Seite 6 · Zum Vergrößern klicken
Seite 6
  • 2. Access method Connect the device to LAN or WAN, user can access and manage the device through Web and SNMP, please see detail information as below. 2.1 Web Device support HTTP protocol, we recommend user to access through IE 6.0, IE 7.0, IE 8.0, IE 9.0, Firefox and Google chrome, the Web access method are as below:
  • Open the browser.
  • Enter the IP address of the ATS in the address bar, support HTTP protocol (user can enable or disable the HTTP function according to situation, for more information please refer to Network Config menu)
  • Enter the valid username and password in the login window.
Digitus 19 Automatic Transfer Switch (DN-95639) — DN-95639_QIG_rev1-0_EN diagram (page 6)
Abb. 4 · DN-95639_QIG_rev1-0_EN
  • The below interface will show up if log success.
Digitus 19 Automatic Transfer Switch (DN-95639) — DN-95639_QIG_rev1-0_EN diagram (page 6)
Abb. 5 · DN-95639_QIG_rev1-0_EN

More detailed information on operation and device configuration can be found in the corresponding user manual.

Page 7 of the Digitus 19 Automatic Transfer Switch (DN-95639) user manual — Quality guarantee
Seite 7 · Zum Vergrößern klicken
Seite 7

Quality guarantee

The product is guaranteed for two years from the date of purchase. If product has already exceeded the warranty period or the problem are caused because of improper operation, a corresponding fee will be charged.

The below cases are not covered by the warranty:

1. Problem caused because of improper maintenance. 2. Problem caused because of unauthorized change, modify or improper use. 3. The device are not used in the stipulate physical environment.

Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address. www.assmann.com Assmann Electronic GmbH Auf dem Schüffel 3 58513 Lüdenscheid Germany

Digitus 19 Automatic Transfer Switch (DN-95639) — Quality guarantee diagram (page 7)
Abb. 6 · Quality guarantee
Page 8 of the Digitus 19 Automatic Transfer Switch (DN-95639) user manual — Automatisches Netzumschaltgerät
Seite 8 · Zum Vergrößern klicken
Seite 8

Automatisches Netzumschaltgerät

Kurzanleitung

DN-95639

Quellen

Referenzen & Links

In dieser Anleitung genannte Seiten – Hersteller, Support und Downloads.

Frage zu Digitus 19 Automatic Transfer Switch (DN-95639) stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Digitus 19 Automatic Transfer Switch (DN-95639)

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Digitus 19 Automatic Transfer Switch (DN-95639) PDF-Anleitung

55 Seiten·522 KB·Switch·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…