
Guía de inicio rápido Español (22–40)
Guide d’utilisation rapide Français (41–59)
Guida rapida Italiano (60–78)
Schnellstart-Anleitung Deutsch (79–97)
Appendix English (98)



(2) 1/8” (3.5mm) to MIDI Adapters
Safety & Warranty Manual
For the latest information about this product (documentation, technical specifications, system requirements, compatibility information, etc.) and product registration, visit headrushfx.com.
For additional product support, visit headrushfx.com/support.

1 3 4 5 6



Setup Items not listed under Introduction > Box Contents are sold separately.

Full-range, flat-response amplifier or
traditional guitar amplifier

Basic Operation This chapter describes some of HeadRush MX5’s basic functions. You can visit headrushfx.com to download the complete user guide for even more information. Main Screen Important: The sequence of models in your signal chain is not necessarily reflected in the footswitches. You can freely assign models to available footswitches without changing your signal chain at all—and vice versa. See Hardware Assign to learn about this.
Tap to view setlists.
Tap and drag this bar downward to view list of rigs.
Rig name.
Tap to save rig.
Turn encoder to move through selectable items onscreen or to adjust parameters. Press encoder as an Enter command.

This button toggles between the different routing options for a rig.
This button enables or disables reverb and delay tails when switching to another rig.
Double-tap a model, In, or Out to show its parameters.
These three blocks show the current function of the three footswitches. Tap the block to activate or deactivate it.
To assign a model (amp, cab, impulse response, or effect) to an empty slot, tap it () and then use the list that appears. See Rigs > Creating a New Rig to learn about this.
To rearrange the models in your signal chain, tap and drag a model to another slot or between two other models (the ones after that position will shift one slot further down the signal chain).
To activate or deactivate a model, press the footswitch assigned to it, or tap the model and then tap the On/Off button that appears in the top right corner.
To show a model’s settings screen, double-tap it.
To load another rig (preset):
To view other options, tap the button in the upper-right corner, and then tap an option.

Footswitch Modes The three footswitches can be used to activate or bypass models (amps, cabs, impulse responses, or effects) as well as select scenes, rigs, or setlists. These footswitches are always in one of four modes: Stomp, Rig, Hybrid, or Setlist.

To change the mode, hold footswitch 1, then:
Footswitches 1-3 correspond to models (amps, cabs, or effects) in your signal chain. Press a footswitch to activate or deactivate its model.
To load the next rig, press footswitches 1 and 2 () simultaneously.
To load the previous rig, press footswitches 2 and 3 () simultaneously.
Footswitches 1-3 correspond to rigs you have previously saved. Press a footswitch to load its rig.
To show the next bank of three rigs, press footswitches 1 and 2 () simultaneously.
To show the previous bank of three rigs, press footswitches 2 and 3 () simultaneously.
The first footswitch can be assigned to activate/ deactivate a model or to select a scene in the currently selected rig.
To switch to the previous rig, press footswitch 2.
To switch to the next rig, press footswitch 3.
To enter the currently shown setlist, press footswitch 1.
To show the previous setlist, press footswitch 2.
To show the next setlist, press footswitch 3.
To enter the All Rigs setlist, press and hold footswitch 1.

Rigs While using HeadRush MX5, a rig is a preset: the combination of assigned models—the amps, cabs, impulse responses, and effects—and the parameter settings of each of them. You can create, edit, save, and load rigs, making it easy to recall the perfect sound for each part of your performance.
Each rig has 11 slots, each of which can have one model (amp, cab, or effect) assigned to it. Assigned slots will show graphical representations of the models, and empty slots will show a symbol.

To create a new rig, tap the button in the upper- right corner of the screen, and tap New Rig.
To assign a model (amp, cab, or effect) to an empty slot:

If you load an amp or cab to a slot with an empty adjacent slot, a matching amp or cab will be loaded automatically to the other slot. After that, you can configure them independently: you can separate them in the signal chain, you can change the type of the amp or cab, and you can delete each model separately.
Optimizing Your Signal Chain The signal chain is the path that the audio signal follows from your guitar through your selected models and ends at the outputs of HeadRush MX5. You can use the touchscreen to arrange your selected models in any sequence, but you may find that some configurations will sound better than others.
Here are some common model placement suggestions for creating tones with HeadRush MX5:

Saving a Rig If you have changed the rig at all since loading it, you will see an asterisk () next to its name at the top of the screen. You can save these changes to this rig, save these changes as another rig, or discard them altogether.
To save a rig, tap Save in the upper-right corner.
To save your changes to the current rig, tap Save.
To save your changes as a new rig, tap Save New Rig, use the keyboard that appears to enter a name, and then tap Save.
To return to the previous screen without saving, tap Cancel at any time.
To discard any changes you’ve made to the rig, tap the button in the upper-right corner, and tap Discard Changes.
Adjusting Settings To adjust the settings of a model in your rig, double-tap it to open its settings screen.
Tap to return to retain your changes and return to the main screen.
Tap this button and tap Discard Changes to discard any changes you’ve made since opening this screen.
Tap the Preset menu to select a preset. See Saving a Preset.
Turn encoder to move through selectable items onscreen or to adjust parameters. Press encoder as an Enter command.

Tap an Off/On parameter button to change the parameter's setting accordingly.
Saving a Preset To save a preset, tap Save in the upper-right corner.
Tap and drag a slider left and right to adjust the parameter's settings. Alternatively, tap the slider and use the encoder for fine adjustments.
Tap the model name to assign a different model to this slot.
Tap a color to assign it to this model. That color will be shown on the main screen, in the Hardware Assign screen, and in the footswitch indicator for this model.
Tap Cancel to return to discard your changes and return to the main screen.
Tap Delete to unassign the model from the slot.
To save your changes to the current preset, tap Save.
To save your changes as a new preset, tap Save New Preset, use the keyboard that appears to enter a name, and then tap Save.
To return to the previous screen without saving, tap Cancel at any time.

Hardware Assign The Hardware Assign screen enables you to customize how HeadRush MX5’s footswitches and an expression pedal control each rig.

To open the Hardware Assign screen, tap the button in the upper-right corner of the main screen, and then tap Hardware Assign.
To return to the main screen, tap the button in the upper-left corner.
To set the color associated with the rig, tap it in the upper-left part of the screen. This color will appear next to the rig name when you view a list of all available rigs or when you view and create setlists. It will also be the color of the corresponding footswitch indicator when HeadRush MX5 is in Rig Mode.
To set the tempo of the rig’s time-based effects (delays, modulation, etc.), tap the button under Tempo to select Current or Fixed.
To set the tempo, press the Tempo footswitch at the desired tempo 3–8 times to set the new tempo in beats per minute (BPM).
To set the tempo, turn the encoder to set the desired tempo in beats per minute (BPM). You can set the tempo only in this Hardware Assign screen.
To load a rig when a MIDI program change is received from an optional external MIDI device, or to send a MIDI program change message when a rig is loaded, tap the button under MIDI, and then turn the encoder to select a MIDI program change number. You can adjust whether MIDI program changes are received and/or sent in the Global Settings menu.
Footswitches The 3 boxes in the lower-left corner represent the 3 footswitches of HeadRush MX5. You can assign any switch-based parameters (ones with only two states) to any of the footswitches— regardless of their location in the signal chain.
To assign a parameter to a footswitch:

Tap Unassigned to unassign that footswitch.
To swap two assignments, tap and drag one of them over the other, and then release it.

Scenes The Scene feature allows you to turn multiple models on or off in each rig, as well as select different change model presets. When you press the footswitch assigned to that scene, all models included in that scene will turn on or off, or change to a different preset, depending on how you assign them. This is a great way to create multiple tones in the same rig. For instance, you may want a particular reverb model to be on anytime a particular distortion model is also on. Alternatively, you may want to turn one delay model off when you turn another one on. Scenes enable you to do this with only one footswitch press.
To create and edit a scene:


To rename a scene (which appears in the footswitch indicators), tap the text in the box below Edit on the model, use the virtual keyboard that appears to enter a name, and then tap anywhere other than the text field.

Expression Pedal The expression pedal can control two parameters (in Classic Mode) or two sets of parameters (in Advanced Mode). Use the toe switch to switch between them—Expression Pedal A or B.
To activate the toe switch, move the “toe end” of the expression pedal so it touches the
MX5, and then press down. Note: When you save your rig, the current selected Expression Pedal state (A or B) will be
saved and then recalled when you load the rig again. The column of four boxes represents the expression pedal settings. You can assign one or more continuously adjustable parameters (ones with a range of values) to the expression pedal.

To set the expression pedal mode, tap the button above Range in the
upper-right corner to select Classic or Advanced.


them over the other, and then release it. To set the range of an assigned parameter: 1. If the Range button is not on, tap it. 2. Tap a value under the Range button. 3. Turn the encoder to set the desired value as a percentage of the parameter’s entire range. Press the encoder or tap elsewhere to confirm the value.


Setlists You can use setlists to organize your rigs. A setlist is a saved collection of rigs, which you can save and recall at a later time. This is useful, for instance, if you only need some of your rigs for a performance; you can save a setlist of just those rigs so you don’t have to spend time searching through all of your rigs before playing the next song. To view your setlists, tap the ≡ button in the upper-left corner of the main screen. The Setlists
screen will appear.
To return to the main screen, tap the button in the upper-left corner. To create a setlist:

To add a rig to the setlist, tap it to add it to the end of the list. Alternatively, tap and hold it, and then drag it to the desired location in the list. You can add the same rig to a setlist more than once. The [Empty ] rig in the lower-left corner is a slot to use as a placeholder to make rearranging the setlist easier; it will not be available as a selectable rig when moving through rigs in the setlist.
To rearrange the setlist, tap and hold a rig in the list on the right half, and then drag it to the desired location in the list.
To remove a rig from the setlist, tap the on its right edge. To save a setlist, tap Save in the upper-right corner.
To save your changes to the current setlist, tap Save.
To save your changes as a new setlist, tap Save New Setlist, use the keyboard that appears to enter a name, and then tap Save.
(At any time) To return to the previous screen without saving, tap Cancel. To discard any changes you’ve made to the setlist, tap the button in the upper-left corner,
and tap Discard Changes. To load a setlist:

same screen you used to create the setlist, where you can edit and save it. To delete a setlist, tap the button on its left side, and then tap the trash can icon. Tap Yes
to confirm the deletion or Cancel to return to the Setlists screen without deleting it.

Hands-Free Mode Hands-Free Mode enables you to adjust any of the settings on your models by using just the footswitches and expression pedal. To enter Hands-Free Mode, press and hold

footswitch 1 to enter the mode select page, and then press and hold footswitch 1 again.
To increase or decrease the value shown, move
the expression pedal.
To decrease the value shown in small increments, press footswitch 1 and 2 () simultaneously.

To increase the value shown in small increments, press footswitch 2 and 3 () simultaneously.
To edit the next model in your rig, press
footswitch 1.
To edit the previous model in your rig, hold
footswitch 1.
model, press footswitch 2.
model, hold footswitch 2.
To exit Hands-Free Mode, press footswitch 3.
Tuner/Tempo You can use the Tuner/Tempo page to tune your guitar and set a tempo for time-based effects. To enter Tuner/Tempo mode, press and hold

footswitch 3 for over one second. While in Tuner/Tempo Mode, the screen to the right is shown.
To change the tuner reference pitch, tap the
parameter and then turn the encoder.
To unmute your signal while tuning, press
footswitch 1.
To enter a tempo via tapping a footswitch,
press footswitch 2 at the desired tempo 3–8 times to set the tempo in beats per minute (BPM).
To exit this page, press footswitch 3. Tip: You can also assign Tap Tempo to a footswitch within a rig on the Hardware Assign page.

Looper The HeadRush MX5 has a built-in looper that you can use to layer your performances. While the looper’s operation is shown in the display, you can control most of it conveniently with the footswitches.
The looper can hold up to 20 minutes of audio at a time across a maximum of 50 layers. The first layer of your loop can be up to 5 minutes long. To record the first layer of a loop, press the Record footswitch. Recording will begin
Rig name.

This meter indicates your current location in the loop during recording or playback.
This controls how much of the looper’s signal you hear in the outputs.
This indicates how many layers are playing in the current loop, including the original.
This controls how much of the looper’s signal is routed back through it when recording another layer.
This indicates the current speed of the loop as a multiple or fraction of the original.
This indicates the length of the current loop.
This indicates the direction of playback.
This indicates whether the looper is located before (Pre) or after (Post) your signal chain. Moving the looper to the Pre position enables you to edit your rig without having to play the same riff over and over again.
immediately and the footswitch indicator will light red. Press the Record footswitch again to stop recording and start loop playback. The footswitch is now called Overdub and the footswitch indicator is yellow. To record additional layers onto the loop (overdub), press the Overdub footswitch.
Overdubbing will begin immediately and the footswitch indicator will light red. Press the Overdub footswitch again to stop overdubbing and continue playback. To erase the top-most (last-added) layer of the loop, press and hold the Peel footswitch. The
top-most layer of the loop will be erased immediately. This process is destructive, so you can’t re-add it later. To clear the full loop, press and hold the Clear footswitch. This process will stop playback and
is destructive, so you can't re-add it later. To halve or double the length of the loop, tap the button next to the Length field and then turn
the encoder. The halving process is non-destructive, so you can restore your original loop and its content by doubling the length of the loop. To halve or double the speed of the looper, tap the button next to the Speed field and then
turn the encoder.

To reverse looper playback, tap the button next to the Playback field and then turn the
encoder.
encoder to place it before (Pre) or after (Post) the signal chain. Moving the looper to the Pre position enables you to edit your rig without having to play the same riff over and over again. To exit the looper and return to the main screen, press the Exit footswitch. If the looper is
playing, playback will continue.
To re-enter the looper, press and hold the Looper footswitch again.
Global Settings Use the global settings to configure the HeadRush MX5’s overall operation.

To show the global settings, tap the
button in the upper-right corner of the screen, and tap Global Settings.
To select each page of the global settings,
tap the number at the upper-right corner of the screen. LCD Brightness: This setting determines the brightness of the main display. Tap this field, turn
the encoder to select 1 (dim) through 5 (bright), and then press the encoder.
Audio Configuration:
Input (Guitar) or the left (L) Return Input (FX Ret L). When set to Per Rig, the source is determined by the Rig Input setting of each rig in the Input block. When set to FX Ret L or Per Rig, the FX-Loop Stereo Return setting will be disabled; the signal will be mono.
(1/4"/6.35 mm, TRS). When set to Line, the output level will be +18 dBu. Use this setting if you are connecting the HeadRush MX5 to a full-range, flat-response amplifier, PA speaker, mixer, or audio interface. When set to Amp, the output level will be +6 dBu. Use this setting if you are connecting the HeadRush MX5 to a traditional guitar amplifier.
(1/4"/6.35 mm, TRS). When set to Rack, the output level will be line level, +18 dBu. Use this setting if you are connecting a rack effects processor in the HeadRush MX5's FX- Loop. When set to Stomp, the output level will be +6 dBu. Use this setting if you are connecting a traditional guitar pedal ("stompbox") in the FX-Loop.
the effects loop is stereo or mono. Tap Send to enable or disable the stereo signal for the Send Outputs. Tap Return to enable or disable the stereo signal for the Return Inputs.

USB Audio Settings:
Sample Rate: This setting determines the sample rate of the USB audio signal: 44.1 kHz, 48.0 kHz
or 96.0 kHz. Remember to select the same sample rate as the one in your DAW. Also, set it before opening your DAW.
signal over a USB connection. Tap On to enable sending of the USB audio signal with the selected Sample Rate. Tap Off to disable the USB audio signal. (To change the Sample Rate, set USB Audio to Off first, select the correct sample rate, set USB Audio to On again, and restart your DAW.)
connection and how its outputs function while doing so:
External Pedal: This setting determines whether or not you are using an external expression pedal with the HeadRush MX5.
you will see a confirmation message if you change the rig while there are unsaved changes on the current one. Tap On to enable these messages or Off to disable them.
Alternatively, tap Do not show this dialog again in the message itself to disable them.
MIDI Settings: These settings determine how the HeadRush MX5 sends and receives MIDI information to and from external devices. These settings affect only the HeadRush MX5’s MIDI input or MIDI output.

throughput; any MIDI information sent to the HeadRush MX5’s MIDI input will be sent directly to the MIDI output. Tap Off to use the HeadRush MX5’s MIDI output normally; the HeadRush MX5 will be able to send its own MIDI information out of the MIDI output.
Off to use the HeadRush MX5’s own internal MIDI clock (which will not be sent out).
change messages when you load a rig. Tap Recv to enable or disable the HeadRush MX5’s reception of MIDI program change messages from an external MIDI device.

receive MIDI messages. Tap this field, turn the encoder to select all channels (Omni), or 1–16, and then press the encoder. Assignments:
you want models to be automatically assigned to the next available switch when you load them. Tap Off if you want models to load without being assigned to a switch; you will have to assign them manually in the Hardware Assign screen. Color Mod:
If you have trouble distinguishing certain colors on your MX5’s display or if you just want to further customize the color scheme, you can use the color mod parameters to adjust their default settings. While experimenting with the settings, a sample of your adjustments will be shown in real time. If you want to return to the default color scheme, the default settings are as follows:
These settings on Page 2 determine if/how equalization is applied for your outputs. This equalizer is a four-band parametric equalizer.

Tip: These settings are especially useful when a venue, rehearsal space, etc. has different acoustic characteristics than the room where you originally created your presets (e.g., the venue may sound “boomier,” or a rehearsal space with soundproofing may deaden some of the high end). This page lets you quickly apply some additional equalization to all of your presets without permanently saving them.
EQ On: This setting determines whether equalization is enabled (On) or disabled (Off) for
the outputs.
cut. This value is applied the level set by the Master knob.
the lowest-frequency band (Low Band) and to the highest-frequency band (High Band): Shelf or Cut.
Low, Low Mid, High & High Mid: The three settings for each of these four frequency
bands determine the shape of the equalization:
The first setting (Hz) determines the center frequency of the low-frequency band, low-mid-frequency band, high-frequency band, or high-mid-frequency band.
The second setting (dB) determines how much the equalizer boosts or cuts the signal at the corresponding frequency band.
The third setting (Q) determines the width of the frequency band. The higher the setting, the wider the band will be around the center frequency (the first setting). This setting is applied whether Low Band or High Band is set to Shelf or Cut.

Transferring Files & Settings Over a USB connection, you can transfer rig, setlist, model preset, loop, and/or impulse response (IR) files between your computer and the HeadRush MX5.

We recommend creating a backup copy of your files to your computer before you make any changes.
Do not disconnect or power off the HeadRush MX5 during the process.
Any unsupported files will be ignored.
You cannot transfer a folder or .zip/archive folder to/from HeadRush MX5. Instead, transfer any supported files directly.
We recommend organizing the file structure of your rigs, setlists, model presets, and/or impulse response files on your computer so that it’s identical to the file structure as shown on the HeadRush MX5 “drive.” To transfer files between the HeadRush MX5 and your computer:
Windows users: If this is the first time you’ve connected it to this computer, you may need to wait a minute while it installs the class-compliant drivers.

As the HeadRush MX5 analyzes and imports the files, a meter on the display will indicate its progress. The normal Global Settings screen will reappear when the process is finished. Do not disconnect or power off HeadRush MX5 during the sync process.

Firmware Update Instructions 1. Connect the USB port on your HeadRush device to your computer, and ensure HeadRush device and your computer are powered on.

Footswitches (3) footswitches with color LEDs
Knobs (1) 300° master volume knob
(1) 360° navigation/data encoder
Display (1) full-color LED-backlit display with touch interface
4” / 102 mm (diagonal)
Connectors (1) 1/4” (6.35 mm) mono input (guitar)
(1) 1/4” (6.35 mm) TRS input (expression pedal)
(1) 1/4” (6.35 mm) stereo output (send)
(1) 1/4” (6.35 mm) stereo input (return)
(2) 1/4” (6.35 mm) balanced output (main)
(1) 1/8” (3.5 mm) stereo output (headphones)
(1) 1/8” (3.5 mm) stereo input (auxiliary device)
(1) 1/8” (3.5 mm) MIDI output
(1) 1/8” (3.5 mm) MIDI input
(1) USB Type-B port
(1) DC power adapter input
Power Connection DC power adapter input
Input Voltage 12 VDC, 3.0 A, center-positive
2.75” x 11.6” x 7.6”
(width x depth x height)
70 x 295 x 195 mm
Weight 3.46 lbs.
1.57 kg
Specifications are subject to change without notice.
HeadRush is a trademark of inMusic Brands, Inc., registered in the U.S. and other countries. Avid and Eleven are registered trademarks of Avid Technology, Inc. in the U.S. and other countries. All other product names, company names, trademarks, or trade names are those of their respective owners.
Dimensions



Manual Version 1.4
In dieser Anleitung genannte Seiten – Hersteller, Support und Downloads.
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.