Benutzeranleitung / Produktwartung RAID 1405 SGL 128 SATA/SAS des Produzenten Adaptec
Zur Seite of 69
Installation and User’ s Guide A dapt ec SA T A/SAS 1405, 1045 Co ntroller.
● 2 Copyright ©2008 Adapt ec, Inc. All rights reser ved. N o part of this publication may be repr oduced, stor ed in a retrieval system, or transm itted in any form or by an y means, electronic, mechanical, phot ocopying, recor ding or otherwise, w ithout the prior w ritten con sent of Adapt ec, Inc.
● 3 Adaptec Cust omer Support If yo u hav e questions about installing or using y our Adaptec pr od uct, check this document first— you will find answers to most o f your q uestions. If yo u need further assistance, use the support options listed below .
● 4 Limited 3- Y ear Hardware W arranty 1. Adapt ec, Inc. (“ Adaptec”) warrant s to the pur chaser of this prod uct that it will be free from defects in mat erial and workman ship for a period of thr ee (3) year s from the date o f purc hase.
● 5 Regulat ory Compliance Statements Federal Com munications Commission Ra dio F requency Interference Stat ement W ARNING: Changes or modifications to this unit not expressly appr ov ed by the party responsible for compliance could v oid the user’ s au thority to operate the equipment.
Contents 1 About This Guide What You Need to Know Before You Begin ................................................... 10 Terminology Used in this Guide ...................................................................... 10 How to Find More Information .
Contents ● 7 Checking Your Controller and Devices ........................................................... 23 Setting the Boot Controller .............................................................................. 23 5 Installing the Driver and an Operating System Before You Begin .
Contents ● 8 Creating the BIOS Kit on Floppy Disks .................................................. 44 Running the AFU .............................................................................................. 45 Running the Menu-Based AFU ...
1 About This Guide In this chapter ... W hat Y ou Need t o Kno w Befor e Y ou Begin .......................................................................... 10 T erminology Used in this G uide ........................................................
Chapter 1: About This Guide l1 0 What Y ou Need to Kno w Before Y ou Begin Y ou should be familiar with compute r hardwar e, data sto rage, and the characteristics of input/ output (I/O) technology used by y our contro ller . Because SAS is a newer I/O technology , an introduction is pro vided in the Ap p en di x A .
2 About SA T A/SAS Controller s In this chapter ... SA T A/SAS Contr oller Featur es .............................................................................................. 12 Abou t the Adapt ec SA T A/SAS 1405 Controller .....................
Chapt er 2: About S A T A/SAS Controlle rs l1 2 SA T A/SAS Controller F eatures ● Supports SAS and SA T A tape drives, autoloaders and libraries. ● Supports S AS and SA T A disk dr ives. ● Supports DVD , Expanders, Disk Enclosures and Backplanes.
Chapt er 2: About S A T A/SAS Controlle rs l1 3 About the Adaptec SA T A/SAS 1405 Controller The A daptec SA T A/SAS 1405 controller is a lo w-pr ofile PCIe c ontroller with these feature s: Form f actor Low-profile Bus compatibility PCIe PCIe bus wid th x4 PCIe bus speed 2.
Chapt er 2: About S A T A/SAS Controlle rs l1 4 About the Adaptec SA T A/SAS 1045 Controller The A daptec SA T A/SAS 1045 controller is a lo w-pr ofile PCIe c ontroller with these feature s: Form f actor Low-profile Bus compatibility PCIe PCIe bus wid th x4 PCIe bus speed 2.
3 Package Cont ents and Syst em R equirements In this chapter ... P ackage Co ntents.............................................................................................................. . ..... 16 Syst em R equirements .......................
Chapter 3: P ackage Contents and System Re quirements l1 6 Package Cont ents ● Ad aptec SA T A/SAS 1405 or 1045 Contr oller ● Embedded in the contro ller’ s BIOS are these utilities:: ● Config.
4 Installing the SA T A/SAS Controller and Disk Drives In this chapter ... Before Y ou Begin ............................................................................................................... ..... 18 Installing the SA T A/SAS Controller.
Chapter 4: Installing the SA T A/SAS Controller and Disk Drives l1 8 Before Y o u Begin ● Read the Safe ty Infor mati on on page 60 . ● Familiarize y ourself with the SA T A/SAS 1405, 1045 controller’ s physical featur es page 12 . ● Ensure that y ou hav e the proper cables for your c ontroller and dev ices page 19 .
Chapter 4: Installing the SA T A/SAS Controller and Disk Drives l1 9 Selecting Disk Drives and Cables Disk Drives The Ad aptec SA T A/S AS contr oller suppor ts both SAS and SA T A disk drives. F or more information about c ompatible disk drives, visit the Ad aptec W eb site at www .
Chapter 4: Installing the SA T A/SAS Controller and Disk Drives l2 0 U se high-quality cables to connect y our controller to y our internal or external dev ice(s).A daptec rec ommends using only A daptec SA T A/SAS cables. For more information or to pur chase cables, visit the Adapt ec W eb site at www .
Chapter 4: Installing the SA T A/SAS Controller and Disk Drives l2 1 2 U se int ernal SAS cables to co nnect the disk drives to the SA T A/SAS contr oller . Note: SAS fan-out cables are also a v ailable with an additional sideband ( SFF-844 8) cabl e that carries SGPIO signals for enclosure management.
Chapter 4: Installing the SA T A/SAS Controller and Disk Drives l2 2 Connecting t o a DVD-R OM In a dir ect -at tac h c onn ecti on, DVD -R OM dri ve s ar e c on nect ed d ir ectl y to a SA S c ontr oll er with SAS cables. The number of direct-attached dev ices is limited to four per SAS connector .
Chapter 4: Installing the SA T A/SAS Controller and Disk Drives l2 3 Checking Y our Controller and Devices Once y ou hav e installed your c ontroller and c onnected y our devices, you can use the A daptec Configuration U tility (A CU) to check your c ontroller and devices, as described belo w : 1 Tu r n o n y o u r c o m p u t e r .
5 Installing the Driver and an Operating Syst em In this chapter ... Before Y ou Begin ............................................................................................................... ..... 25 Creating a Driv er Disk ....... ...........
Chapter 5: Inst alling the Driv er and an Operating System l2 5 Before Y o u Begin ● Install and co nnect your c ontroller and disk drives, (see page 18 ). ● Crea te a driv er disk (see the following section). Creating a Driver Disk Before y ou install the driv er , you must cr eate a drive r disk.
Chapter 5: Inst alling the Driv er and an Operating System l2 6 Installing with Re d Hat Enter prise Linux Y ou wil l need your R ed Hat Installation CD to complete this task. T o install the SA T A/SAS controller dr iver while installi ng Red H at Enter pri se Linux: 1 Inser t t he Red Hat In stal lat ion CD .
6 Installing the Driver on an Existing Operating Syst em In this chapter ... Before Y ou Begin ............................................................................................................... ..... 28 Creating a Driv er Disk ....... ...
Chapter 6: Installing the Driver on an Existing Operat ing System l2 8 Before Y o u Begin Before y ou begin, install and connect your c ontroller and disk drives (see page 18 ). Y ou must also create a driv er disk (see next sect ion) before y ou begin installing the controlle r driver .
Chapter 6: Installing the Driver on an Existing Operat ing System l2 9 Installing on Windows Vista or Windo ws Ser ver 2008 1 Insert the Windo ws setup CD . 2 Right-cl ick the Comp uter and select Ma na ge . 3 From th e Computer Management , select Device Manager t o open the list.
7 Configuring the Controller Utility In this chapter ... U sing the A daptec C onfiguration Utility .............................................................................. 31 Starting Adaptec Configuration U tility .............................
Chapter 7: Configuring the Contr oller Utility l3 1 Using the Adapt ec Configuration Utility The A daptec Co nfiguration Utility (A CU) allo ws yo u to manage and co nfigure the A daptec SA T A/SAS c ontroller and the respectiv e devices that ar e connect ed to it.
Chapter 7: Configuring the Contr oller Utility l3 2 The Contr oller Configuration menu displa ys the following options: ● Contr oller Pr operties ● Cont rolle r Conf igur at ion ● PHY Configurat.
Chapter 7: Configuring the Contr oller Utility l3 3 The Controller P roperties display s the following information. ● PCI slot number in which the SA T A/SAS contr oller is connected ● Int errupt .
Chapter 7: Configuring the Contr oller Utility l3 4 ● BBS Support - Controller If th e BBS Suppor t is Cont roller , the syst em will boot from the Controller , and set the disk that you wish to boot as Set B ootable . If you want to boo t the system f rom one of the dev ices c onnected, then select the option Device in the BBS Support .
Chapter 7: Configuring the Contr oller Utility l3 5 Using the Disk Utilities The Disk Utilities allo w y ou to v erify , format, or locate a drive, and set a disk as bootable dev ice. T o access the Disk Utilities Pr ess CTRL + A to acc ess the A daptec Configuration U tility .
Chapter 7: Configuring the Contr oller Utility l3 6 2 Now s e l e c t Ve r i f y D i s k M e d i a and press <Enter>. 3 A confirmation window appears. Click Ye s to verify the disk or No to ca nc el . Locating a Disk 1 Select the disk you want to locat e and press <Enter>.
Chapter 7: Configuring the Contr oller Utility l3 7 3 The device that is set as a bootable device is indicated with "+" symbol in the screen. Note: The select ed bootable de vice will be the bo ot de vice when "BBS Support" has been set to "Controller" on the "Contr o ller Configuration " menu.
8 Enclosure Management Suppor t In this chapter ... Connecting Driv e LED Contr ol Cables ................................................................................. 39 Behavioral P atte rn of Dr iv e LED ........................................
Chapter 8: Enclosure Management Support l3 9 Connecting Drive LED Control Cables Drive LED Contr ol Cables helps you to det ect/verify the faulty dr iv es and slots in the Backplane or Enclos ure. U sing an int ernal SA T A fan-out cable, connect the contr oller to the SA T A/SAS of the bac kplance.
Chapter 8: Enclosure Management Support l4 0 ● Locate Disk and Slots - I f you want t o locate an y disk/slot using the contr oller’ s configuration utility , the Indicat e LED option allo ws you t o blink the LED on the particular disk/slots.
9 Solving Problems In this chapter ... T roubleshooting Checklist ............................................................................................... ...... 4 2 This chapter provides b asic troubleshoot ing in formation and solutions for solving your SA T A/ SAS controller problems.
Chapter 9: Solv ing Problem s l4 2 T roubleshooting Checklist If y ou encount er difficulties installing or using the SA T A/SAS controller , check these it ems first: ● W ith your c omputer po wered off, c heck the connections to eac h disk dev ice, the pow er supply , the LED connect or , and so on.
10 Using the Adapt ec Flash Utility f or DOS In this chapter ... Introduction ................................................................................................................... ........ 44 Syst em R equirements .......................
Appendix 10: Using t he Adaptec Flash Ut ility for DOS ● 44 Introduction The AFU is a DOS utility , whic h allows y ou to updat e, sav e and v erify the SA T A/SAS con t rol le r ’ s BI OS . System R equirements The following are the requir ements of AFU: ● MS–DOS version 5.
Appendix 10: Using t he Adaptec Flash Ut ility for DOS ● 45 Running the AFU The AFU can be ex ecuted in tw o ways: ● R unning the M enu-Based AFU ● R unning the AFU fr om the Command Li ne Running the Menu-Based AFU The easiest way t o run the AFU is to use its GUI.
Appendix 10: Using t he Adaptec Flash Ut ility for DOS ● 46 ● HELP (next section) ● LIST on page 46 ● SA VE on page 46 ● UPD A TE on page 47 ● VERIFY on page 48 ● VERSION on page 48 HELP The HELP command displa ys a summary of AFU funct ions and command switches.
Appendix 10: Using t he Adaptec Flash Ut ility for DOS ● 47 The default value 0 indicates that the re are m ultiple SA T A/SAS contr ollers in the system, and the values can be modified wheneve r needed.
Appendix 10: Using t he Adaptec Flash Ut ility for DOS ● 48 Adaptec Flash Utility V1.0 (c)Adaptec In c. 1999–2008. Al l Rights Reser ved. Updating Cont roller 0 (ASC-10 45/1405) Reading flash imag.
Appendix 10: Using t he Adaptec Flash Ut ility for DOS ● 49 A:> AFU VERS ION /C 0 Adaptec Flash Utility V1.0 (c)Adaptec In c. 1999–2008. Al l Rights Reser ved.
A Introduction t o SAS In this chapter ... T erminology Used in This A ppendix ........................................................... ......................... 51 W hat is SAS? .....................................................................
Chapter A: Intr oduction to SAS l5 1 T erminology Used in This Appendix For c on ve nience, SA T A/SAS contro llers are re ferred t o generically in this appendix as SAS contr ollers. HBA s, disk drives, and ext ernal disk drive enc losures ar e ref erred to as end dev ices and expanders ar e refe rred to as expander dev ices .
Chapter A: Intr oduction to SAS l5 2 How do S AS Devices Communicat e? SAS devices comm unicate with each other thr ough links. A link is a phy sical connection between tw o ph ys.
Chapter A: Intr oduction to SAS l5 3 SAS controller port options var y . A SAS controller with four phys c ould be configur ed with one wide port , with two wide ports that comprise two ph ys, or with four narro w ports each containing one ph y . (A w ide port w ith four phys is referred t o as a 4-wi de or 4x port.
Chapter A: Intr oduction to SAS l5 4 In par all el SCS I, XX is the disk dr ive ’ s channel number , YY is the target number , and ZZ is the logical unit number (L UN). What are the SAS Connection Options? Y ou can connect e nd dev ices to each other through direct cable c onnections and through backplane connections.
Chapter A: Intr oduction to SAS l5 5 Y ou can use only one fanout expander in an y single SAS domain (a topology of SAS—and possibly SA T A—end dev ices and expander devices). A single SAS domain can ther efore comprise up to 16,384 SAS ports (and therefor e up to 16,384 SAS addr esses).
Chapter A: Intr oduction to SAS l5 6 Req uires bus termination Requires no bus t ermination Standard SCSI connecto rs SAS connectors (see pag e 19 ) Parallel SCS I Serial Attached SC SI.
B SAS Contr oller LED and I2C and SGPIO Connect or R ef erence In this appendix... Ad aptec 1045 LED Connector Specification......................................................................... 58 Ad aptec 1405 LED and I2C and SGPIO Connector Specification .
Chapter B: SAS Controller LED and I2C and SGPIO Connect or Reference l5 8 Adapte c 1045 LED Connect or Specif ication ● A daptec 1045 A ctivit y LED Board Connector: Mo lex 22-28-8022 2.54mm 1x2 RA H eader or equivalent ● LED Mating Cable Connec tor: Molex 5 0-57-9002 or equivale nt J1 Note: Aggregate LED signals only .
Chapter B: SAS Controller LED and I2C and SGPIO Connect or Reference l5 9 SFF-808 7 I2C Connect or J7 SFF-808 7 SGPIO Connector J7 Adapte c 1405 I2C Connect or Specification ● A daptec 1405 I2C Boar.
C Sa fet y I n for m at io n T o ensure y our personal safet y and the safet y of your equipment: ● K eep y our work ar ea and the c omputer c lean and clear of debris.
D T echnical Specifications In this chapter ... Envir onmental Specifications .................................................... ............................................ 62 DC P ow er Requir ements ...............................................
Appendix D: T echnical Specif ications ● 62 Environmental Specif ications Note: F orced air flow is recommended, but not required. DC Po wer R equirements Ambient te mperature wit hout forced airflow 0°C to 55° C Rela tive humidity 1 0% to 9 0%, noncondensing Altitude up to 3,000 meters PCIe DC V oltage 3.
Glossary A activity See task . AFU A daptec Co nfiguration Utility . An application used to up date, sa ve and v erify the SA T A/SAS contr oller’ s BIOS. ATA A T Bus A ttachment. St andard parallel int erface t o IDE hard disks typically used in desktop c omput ers and some entr y-level servers.
Glossar y ● 64 check point A feature that enables y ou to exit the A CU when an oper ation is in progress and be able to c ontinue without interruption. The driver then resumes the operation fr om where the BIOS left off and the BIOS resumes the operation where the driv er left off.
Glossar y ● 65 I impacted An impact ed array is one which ha s been creat ed but for some r eason the initial build ope ration did not complete. All member drives are pr esent and operational, and all data wr itten to the array is prot ected. T o opt im ize th e arra y , run a V erif y wit h Fi x T ask .
Glossar y ● 66 simple volume A vol ume made up of disk space from a single disk . It can consist of a single region on a disk, or concat enated multiple regions of the same disk. T task An operation that occur s only on the SA T A/SAS contr oller , asynchronous t o all other operations; for example, initializing or v erifying a disk.
Index A Adaptec Flash Utility. See AFU AFU 44 B backplane connections 21 , 54 D direct-attach connections 20 , 54 disk drives SAS identifiers 53 drivers installing on Linux 29 installing on Windows 28.
Index ● 95 transceivers 52 wide connectors 53 wide ports 52 SAS devices 51 SATA/SAS direct-attach connections 20 SCSI comparison to SAS 55 Setting the Controller Configuration 33 storage management .
A daptec, Inc. 691 South Milpitas Boulevard Milpitas, CA 95035 USA ©2008 Adaptec, Inc. All rights reserved. Adaptec and the Adaptec logo are trademarks of Adaptec, Inc.
Ein wichtiger Punkt beim Kauf des Geräts Adaptec RAID 1405 SGL 128 SATA/SAS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Adaptec RAID 1405 SGL 128 SATA/SAS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Adaptec RAID 1405 SGL 128 SATA/SAS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Adaptec RAID 1405 SGL 128 SATA/SAS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Adaptec RAID 1405 SGL 128 SATA/SAS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Adaptec RAID 1405 SGL 128 SATA/SAS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Adaptec RAID 1405 SGL 128 SATA/SAS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Adaptec RAID 1405 SGL 128 SATA/SAS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Adaptec RAID 1405 SGL 128 SATA/SAS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
