Benutzeranleitung / Produktwartung L0609466 des Produzenten Bosch
Zur Seite of 26
Installation Instructions Bosch Dual Fuel Range Slide-In Model.
Table of Contents Safety ...................................................... 1 Installation ................................................. 3 Before You Begin ............................................................. 3 Installation Procedure .
Safety IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Important Safety Instructions Appliance Handling Safety Safety Codes and Standards Electric Safety WARNING: Do not repair or replace any part of the appliance unless specifi- cally recommended in the manuals.
,_Safety Gas Safety • Be sure your appliance is properly installed and grounded by a qualified tech- nician. Installation, electrical connections and grounding must comply with all applicable codes. • Install a gas shutoff valve near the appliance.
Related Equipment Safety ,_ Safety • Warning: All ranges can tip. Injury to persons could result. Install anti-tip device packaged with range. Verify that the anti-tip devices are engaged. See installation instructions. Figure 2: Tipping Precautions • Remove all tape and packaging before using the appliance.
Installation Tools and Parts Needed Additional Parts Needed For Hard Wire Installations Parts Included General Information Range Power Supply Cord Kit (240V -30 Amp) Note: Not necessary for Canadian installations; Canadian units are shipped with the power cord already installed.
Preparation Installation Prepare Unit Remove all packaging material and discard. Tip: Place the range on a piece of the cardboard to protect floors. Remove drawer and set aside. 1. Pull drawer all the way out. 2. Locate locking clips on the rails, one on each side.
Installation Electrical Requirements 4. Close the door until it stops. It will be about half- way open. 5. Holding the door firmly on both sides and using both hands, pull the door straight out of the hinge slots. Hold firmly, the door is heavy. 6. Place the door in a stable location.
Gas Requirements Installation _k_ cauti°n: Make certain that gas shutoff valve and all burner controls are in the OFF position before beginning. Shut off main gas supply valve before disconnecting the old range and leave it off until the new hook-up has been completed.
Installation Allow a minimum of 30 inches between cabinets where range isto be installed 1.. _. ..... F _ . 30" _£16_ ........... Figure 5: Cutout Requirements - Typical Installation Note: The slide-in range can also replace a freestanding range.
Installation ® 4" (10.2 cm) rain. 1 30" (76.2 cm) '_ min. centered 30" (76.2 cm) min. no clearance required (12 mm clearance required in Canada) ® 4" (10.
Installation 2. Secure bracket with 2 screws adequate for mounting surface (i.e., forwood floor usewood screws, for concrete flooruse concrete anchors andscrews).
Installation Install 2 screws through holes in trim andin range backwall. See Figure 9: Back- wall Trim Strip andFigure 10: Install Backwall Trim _rip Backwall Trim Strip Figure 9: Backwall Trim Strip j. . Back of Range Figure 10: Install Backwall Trim Strip Connect Electric There are two possible electrical connections: 1.
Installation Install Strain Relief Place strain relief in knockout below terminal block. See Figure 11: Strain Relief Knockout. ,_ Warning: The strain relief provided with your range cord must be properly installed. Strain reliefs vary. Carefully read and follow the instructions included with your strain relief.
Installation Warning: Risk of Electric Shock or Fire. Frame grounded to neutral through a ground strap. Grounding through the neutral conductor is prohibited for new branch-circuit installations (1996 NEC), mobile homes, and recreational vehicles, or in an area where local codes prohibit grounding through the neutral conductor.
Installation . Remove top nut, star washer, and round washer from each post. Note: DO NOT remove last round washer, last nut or internal wiring leads. . 5. Remove screw from bottom end of ground strap. Remove ground strap from center post, rotate so that wide end is at top and attach wide end to range through hole below junction box.
10. Properly secure strain relief (see previous section). Note: DONOT plug in range at this time. Installation Three Wire Range Cord Connection The Four Wire Connection (above) is preferred, but where.
Installation 7. Tighten all connections securely andreplace terminal block cover. / green ground screw Figure 18: Completed Three Wire Range Cord Connection 8. Properly secure strain relief. See "Install _rain Relief' on page 12 for detailed instructions.
Important note for LP users Flexible Connector Method Installation The range is shipped from the factory for use with natural gas. For use with pro- pane (LP) gas, your range must first be converted using the LP conversion kit. If using rigid pipe, skip to "Rigid Pipe Method" on page 19.
Installation drawer adjustable leg Figure 21: Adjust the Front Leveling Leg Slide Range into Opening . 2. Plug in power cord. Slide range into opening, being careful not to damage countertops, floors, or the range drawer front. Do not apply pressure to cooktop when sliding into position.
Rigid Pipe Method Adjust Front of Range for Proper Installation Installation 1. Adjust front leveling legs so that the cooktop trim rests snugly against the countertop all the way around. 2. Verify that both front legs are resting solidly on the floor.
Installation . Make sure circuit breaker is off and then plug range cord into electrical outlet. Caution: Before you plug in an electrical cord, be sure all controls are in the Off position. 2. Line up range in front of opening. 3. Measure back left corner of opening from floor to top of countertop.
Installation to verify thatboth back legs are resting solidly on the floor. Also verify that the leftrange legis under the anti-tip bracket. Caution: Verify thatthe weight of the range is not resting on the countertop. This could result in damage to the countertop andthe appliance.
Installation Test the Installation Turn on power at breaker Test self-clean lock Test Rangetop Burners: Caution: If the display flashes and beeps, the polarity of the wiring may be reversed. Reversed polarity can damage the range and can result in electrical shock hazard.
Yellow Flames: Further adjustment is required. Yellow Tips on Outer Cones: Normal for LP Gas. Soft Blue Flames: Normal for Natural Gas. If the flame is completely or mostly yellow, verify that the regulator is set for the correct fuel. After adjustment, retest.
5551 McFadden Avenue, Huntington Beach, CA 92649 • 800-944-2904 • www.boschappliances.com 9000135014 (No ECO) ° 10089 Rev A ° 04/06 • © BSH Home Appliances Corporation • Litho U.
Ein wichtiger Punkt beim Kauf des Geräts Bosch L0609466 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Bosch L0609466 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Bosch L0609466 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Bosch L0609466 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Bosch L0609466 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Bosch L0609466 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Bosch L0609466 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Bosch L0609466. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Bosch L0609466 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
