
Operating Instructions Bedienungsanleitung Instructions d’utilisation Istruzioni per l’uso Gebruiksaanwijzing Manual de instrucciones Brugsvejledning Driftsföreskrifter Bruksanvisning Käyttöohjeet
Cordless Impact Driver/Cordles Impact Wrench
Akku-Schlagschrauber/Akku-Schlagschrauber Perceuse à impact sans fil/Perceuse à impact sans fil Avvitatore ad impulsi senza fili/Avvitatore ad impulsi senza fili
Snoerloze slagschroevendraaier/Snoerloze slagschroevendraaier Destornillador de impacto inalámbrico/Destornillador de impacto inalámbrico
Akku-slagboremaskine/Akku-slagboremaskine Sladdlös slagskruvdragare/Sladdlös slagskruvdragare
Trådløs slagbormaskin/Trådløs slagbormaskin Langaton iskuruuviavain/Langaton iskuruuviavain
Before operating this unit, please read these instructions completely and save this manual for future use. Vor Inbetriebnahme des Gerätes die Betriebsanleitung bitte gründlich durchlesen und diese Broschüre zum späteren Nachschlagen sorgfältig aufbewahren. Lire entièrement les instructions suivantes avant de faire fonctionner l’appareil et conserver ce mode d’emploi à des fins de consultation ultérieure. Prima di usare questa unità, leggere completamente queste istruzioni e conservare il manuale per usi futuri. Lees deze gebruiksaanwijzing aandachtig door voor u het apparaat in gebruik neemt en bewaar de gebruiksaanwijzing voor eventuele naslag. Antes de usar este aparato por primera vez, lea todas las instrucciones de este manual y guarde el manual para poderlo consultar en el futuro. Gennemlæs denne betjeningsvejledning før brugen og gem den til fremtidig brug. Läs igenom hela bruksanvisningen innan produkten tas i bruk. Spara bruksanvisningen för senare användning. Før enheten tas i bruk, vennligst les disse alle anvisningene og oppbevar bruksanvisningen for senere bruk. Lue ohjeet huolella ennen laitteen käyttöönottoa ja säilytä tämä käyttöohje tallessa tulevaa tarvetta varten.


FUNCTIONAL DESCRIPTION FUNKTIONSBESCHREIBUNG DESCRIPTION DES FONCTIONS DESCRIZIONE DELLE FUNZIONI FUNCTIEBESCHRIJVING DESCRIPCIÓN FUNCIONAL FUNKTIONSBESKRIVELSE FUNKTIONSBESKRIVNING FUNKSJONSBESKRIVELSE TOIMINTOJEN KUVAUS


Recommendations for use / Gebrauchsempfehlungen / Recommandations concernant l’utilisation / Precauzioni d’uso / Aanbevelingen voor gebruik / Recomendaciones par el uso / Anbefalinger for brugen / Rekommendationer för användning / Anbefalt bruk / Käyttösuositukset
Pack cover Akkuabdeckung Couvercle de la batterie autonome Coperchio pacco Accudeksel
Cubierta de batería Pakningsdæksel Batteriskydd Pakkedeksel Akkukotelon kansi
Terminals Anschlüsse Bornes Terminali Aansluitpunten
Terminales Terminaler Poler Ender Liittimet
label Schild rouge rossa
label rojo etikette dekal
etikett merkki



Read “the Safety Instructions” booklet and the following before using.
SAFETY RULES 1) Wear ear protectors when using the tool for extended periods.
EY7546_EY7547_EY7550_EY7551_EU_001(EN).indd 9 2012-10-12 13:11:14

Attaching or Removing Original Options and Sockets Keep the body above freezing point (0°C 32°F) when attach or detach original options and sockets to the square drive on the body. The cushion rubber in the square drive to push up the ball may get hard under freezing point. This requires extra force in detaching and attaching sockets. Attaching or Removing Bat tery Pack
1. Hold the collar of quick connect chuck and pull it out from the driver. 2. Insert the bit into the chuck. Release the collar. 3. The collar will return to its original position when it is released. 4. Pull the bit to make sure it does not come out. 5. To remove the bit, pull out the collar in the same way. CAUTION: • If the collar does not return to its origi- nal position or the bit comes out when pulled on, the bit has not been properly attached. Make sure the bit is properly attached before use.
Use 6.35 mm hexagonal bits. To ensure proper securement of the bit, use only hexagonal bits with 9.5 mm detent.
6.35 mm 9.5 mm
Alignment marks · Button

To prevent damage, do not operate Forward/Reverse lever until the bit comes to a complete stop. Forward Rotation Switch Operation
To Change the Belt Hook Location Side The belt hook can be attached to either side of the unit. 1. Removing the hook (1) Remove the nut. (2) Draw out the hook.
securely fastened.
Forward Reverse · Switch lock

To set the center of a hole, pull the trigger slightly to start the bit rotation slowly. The more the speed control trigger is pulled, the higher the speed becomes. CAUTION: When operating the tool by pulling the trigger, there may be a momentary lag before rotation starts. This does not signal a malfunction.
* i.p.m. = Impact per minute.
Avoid repeatedly depressing the switch when the bolts and screws are securely fastened. Not doing so may cause a delay in rotation starting, or the Impact Power mode display to flash and prevent rotation from starting for circuit protection.

Pressing the button toggles the LED light on and off. The light illuminates with very low cur- rent, and it does not adversely affect the per- formance of the driver during use or its battery capacity.
(1) Impact Power Mode Select
Selecting the impact power among 3
modes (Soft, Medium, Hard). Press the impact power mode button to set it. The mode changes to hard, medium, or soft each time the button is pressed. The driver is preset to “hard” impact mode setting when shipped from the manufac- turer. Recommended work guideline table
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

(3) Overheat warning lamp
more than a 15°C difference between the temperatures of the battery and the
charging location.)
(4) Battery low warning lamp
Indicates operation has been halted due to motor or battery overheating.
Flashing (No charge) Battery protection feature active
Use the grip to hold and operate the driver with one hand. If the job requires additional force, you can push against the rear end of the driver with your other hand.
Off (normal operation) · Off (normal operation)

[Battery Charger] Charging
be affected by foreign substances such as dust and water etc. during operation. • When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together
The rechargeable batteries have a lim- ited life. If the operation time becomes extremely short after recharging, replace the battery pack with a new one. Battery Recycling
Your battery pack is not fully charged at the time of purchase. Be sure to charge the battery before use.
For environmental protection and recy- cling of materials, be sure that it is dis- posed of at an officially assigned loca- tion, if there is one in your country.

5. When charging is completed, the charging lamp in green color will turn off. 6. If the temperature of the batter pack is 0°C or less, charging takes longer to fully charge the battery pack than the standard charging time. Even when the battery is fully charged, it will have approximately 50% of the power of a fully charged battery at normal oper- ating temperature. 7. Consult an authorized dealer if the charging lamp (green) does not turn off. 8. If a fully charged battery pack is inserted into the charger again, the charging lamp lights up. After several minutes, the charg- ing lamp in green color will turn off. 9. Remove the battery pack while the battery pack release button is held up.
Battery pack release button
ing until the battery cools down. Charging will then begin automatically. 4. The charge lamp (green) will flash slowly once the battery is approximately 80% charged.
Charging is completed. (Full charge.)
Battery is approximately 80% charged.
Now charging.
Charger is plugged into the AC outlet. Ready to charge.
(Green) (Orange) Charging Status Lamp. Left: green Right: orange will be displayed.
Battery pack is cool. The battery pack is being charged slowly to reduce the load on the battery.
Battery pack is warm. Charging will begin when temperature of battery pack drops. If the temperature of the battery pack is -10° or less, the charging status lamp (orange) will also start flashing . Charging will begin when the temperature of the battery pack goes up"
Charging is not possible. Clogged with dust or malfunction of the bat- tery pack.
Turn off Lit Flashing
Battery charger · Alignment marks

Information for Users on Collection and Disposal of Old Equip- ment and used Batteries
These symbols on the products, packaging, and/or accompanying docu ments mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used bat teries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inap propriate waste handling. For more information about collection and recycling of old products and bat teries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. Penalties may be applicable for incorrect disposal of this waste, in ac cordance with national legislation. For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. IV. MAINTENANCE
variety of factors including the followings. After tightening, always check the torque with a torque wrench. 1) Voltage When the battery pack becomes near- ly discharged, the voltage decreases and the tightening torque drops.
EY75A1 14.4 V
M10 x 35 mm M12, M14, M16 x 45 mm
Standard bolt N × m (kgf-cm)
196.0 (2000)
The power required for tightening a bolt will vary, according to bolt material and size, as well as the material being bolted. Choose the length of tightening time accordingly. Reference values are provided below. (They may vary according to tightening conditions.)
147.0 (1500)
98.0 (1000)
Factors Affecting Tightening Torque
M12
49.0 (500)
The tightening torque is affected by a wide
0.5 0.0 1.0 1.5 2.0 2.5 3.0
Tightening time (Sec.)
EY7546_EY7547_EY7550_EY7551_EU_001(EN).indd 16 EY7546_EY7547_EY7550_EY7551_EU_001(EN).indd 16 2012-10-11 16:40:47 2012-10-11 16:40:47
Tightening torque

EY75A1 18 V
M8, M10 x 35 mm. M12 x 45 mm
M10 x 35 mm M12, M14, M16 x 45 mm
N × m (kgf-cm)
Standard bolt N × m (kgf-cm)
196.0 (2000)
196.0 (2000)
147.0 (1500)
147.0 (1500)
M12
98.0 (1000)
98.0 (1000)
M10
M12
49.0 (500)
49.0 (500)
M10
0.5 0.0 1.0 1.5 2.0 2.5 3.0
0.5 0.0 1.0 1.5 2.0 2.5 3.0
Tightening time (Sec.)
Tightening time (Sec.)
EY75A1 18 V
M10 x 35 mm M12, M14, M16 x 45 mm
M8, M10 x 35 mm. M12 x 45 mm
N s m (kgf-cm)
N × m (kgf-cm)
196.0 (2000)
196.0 (2000)
147.0 (1500)
147.0 (1500)
98.0 (1000)
98.0 (1000)
M10
49.0 (500)
49.0 (500)
M8
M10
0.5 0.0 1.0 1.5 2.0 2.5 3.0
0.5 0.0 1.0 1.5 2.0 2.5 3.0
Tightening time (Sec.)
Tightening time (Sec.)
EY75A2 18 V
M8, M10 x 35 mm. M12 x 45 mm
M10 x 35 mm M12, M14, M16 x 45 mm
N s m (kgf-cm)
N s m (kgf-cm)
196.0 (2000)
196.0 (2000)
147.0 (1500)
147.0 (1500)
98.0 (1000)
98.0 (1000)
M10
49.0 (500)
49.0 (500)
M12
M10
0.5 0.0 1.0 1.5 2.0 2.5 3.0
0.5 0.0 1.0 1.5 2.0 2.5 3.0
Tightening time (Sec.)
Tightening time (Sec.)
EY7546_EY7547_EY7550_EY7551_EU_001(EN).indd 17 EY7546_EY7547_EY7550_EY7551_EU_001(EN).indd 17 2012-10-11 16:40:47 2012-10-11 16:40:47

M8, M10 x 35 mm. M12 x 45 mm
N s m (kgf-cm)
196.0 (2000)
147.0 (1500)
98.0 (1000)
same bolt, according to grade, length, and torque coefficient (the fixed coefficient indi- cated by the manufacturer upon produc- tion). Tightening torque will vary, even with
49.0 (500)
the same bolting material (e.g. steel), accord ing to the surface finish. Torque is greatly reduced when the bolt
0.5 0.0 1.0 1.5 2.0 2.5 3.0
Tightening time (Sec.)
and nut start turning together. 5) Socket play Torque is lowered as the six-sided configu ration of the socket of the wrong size is used to tighten a bolt. 6) Switch (Variable speed control trigger) Torque is lowered if the unit is used with the switch not fully depressed. 7) Effect of Connecting Adaptor The tightening torque will be lowered through the use of a universal joint or a connecting adaptor.
Steel plate thickness 10 mm
Tightening conditions • The following bolts are used. Standard bolts: Strength type 4.8 High tensile type 12.9
Explanation of the strength type
Bolt yield point (80% of tensile strength) 32 kgf/mm2 (45000 psi) Bolt tensile strength 40 kgf/mm2 (56000 psi)
Use only suitable size of bit. Panasonic original Optional Quick change chuck (EY9HX110E). Chuck Size: 6.35 mm hex VII. APPENDIX
Screw driving Wood screw 3.5 mm - 9.5 mm Self-drilling screw 3.5 mm - 6 mm
EY7546_EY7547_EY7550_EY7551_EU_001(EN).indd 18 EY7546_EY7547_EY7550_EY7551_EU_001(EN).indd 18 2012-10-11 16:40:48 2012-10-11 16:40:48

Model EY75A1 EY75A2 Motor voltage 14.4 V DC 18 V DC 14.4 V DC 18 V DC
soft mode 0 - 1000 min-1
medium mode 0 - 1400 min-1
hard mode 0 - 2500 min-1 0 - 2300 min-1 Maximum torque 150 N·m 155 N·m 200 N·m 205 N·m
soft mode 0 - 2000 min-1
medium mode 0 - 2800 min-1
hard mode 0 - 3000 min-1 0 - 3500 min-1
Overall length 143 mm 155 mm Weight (with battery pack: EY9L44) 1.55 kg - 1.55 kg -
Model EY9L41 EY9L42 EY9L44 EY9L45 EY9L50 EY9L51
Storage battery Li-ion Battery
Battery voltage 14.4 V DC (3.6 V x 4 cells)
14.4 V DC (3.6 V x 8 cells)
18 V DC (3.6 V x 10 cells)
Electrical rating See the rating plate on the bottom of the charger Weight 0.93 kg
EY9L41 EY9L42 EY9L44 EY9L45 EY9L50 EY9L51 Usable:
45 min Usable:
30 min Usable:
50 min Usable:
65 min Usable:
50 min Usable:
65 min Full: 60 min Full: 35 min Full: 65 min Full: 80 min Full: 65 min Full: 80 min
Electrical rating See the rating plate on the bottom of the charger Weight 0.93 kg
EY9L41 EY9L42 EY9L44 EY9L45 EY9L50 EY9L51 Usable:
35 min Usable:
30 min Usable:
40 min Usable:
50 min Usable:
40 min Usable:
55 min Full: 50 min Full: 35 min Full: 55 min Full: 60 min Full: 55 min Full: 70 min
Please refer to the latest general catalogue. NOTE: For the dealer name and address, please see the included warranty card.
EY7546_EY7547_EY7550_EY7551_EU_001(EN).indd 19 EY7546_EY7547_EY7550_EY7551_EU_001(EN).indd 19 2012-10-11 16:40:48 2012-10-11 16:40:48

The wires in this mains lead are coloured in accordance with the follow- ing code: Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the termi- nals in your plug, proceed as follows. The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. Under no circumstances should either of these wires be connected to the earth ter- minal of the three pin plug, marked with the letter E or the Earth Symbol .
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rat- ing of 5 amp and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UN- SUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse and fuse cover if it is removable.
This apparatus was produced to BS800.
Fuse Cover
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.