DE
Panasonic logo
Offizielle Bedienungsanleitung

Panasonic EY6220

36 Seiten·328 KB·Akkubohrschrauber·PDF·ENJA
Panasonic EY6220
Inhaltsverzeichnis 20 Abschnitte Cordless Drill & Driver · Akku-Bohrschuber Perceuse et tournevis sur batterie · Ledningsfri bor og skrutrækker Laddningsbar borr/skruvdragare · Oppladbar drill og skrutrekker Ladattava porakone/ruuvinväännin · … AnzeigenAusblenden
Page 1 of the Panasonic EY6220 user manual — Ledningsfri bor og skrutrækker Laddningsbar borr/skruvdragare
Seite 1 · Zum Vergrößern klicken
Seite 1

Instruction Manual Betriebsanleitung Manuel d’instructions Manuale delle istruzioni Handleiding Manual de instrucciones Brugervejledning Bruksanvisning Brukerveiledning Käyttöohje

R

Cordless Drill & Driver

Akku-Bohrschuber Perceuse et tournevis sur batterie

Trapano e cacciavite senza filo Draadloze boor en schroevedraaier Taladro y destornillador sin cable elétrico

Ledningsfri bor og skrutrækker Laddningsbar borr/skruvdragare

Oppladbar drill og skrutrekker Ladattava porakone/ruuvinväännin

EY6220 EY503

Before operating this unit, please read these instructions completely.

Vor Inbetriebnahme des Gerätes, die Betriebsanleitung bitte gründlich durchlesen.

Lire entièrement les instructions suivantes avant de faire fonctionner l’appareil.

Prima di usare questa unità, leggere attentamente queste istruzioni.

Lees deze gebruiksaanwijzing aandachtig door alvorens het appraat in gebruik te nemen.

Antes de usar este aparato por primera vez, lea todas las instrucciones de este manual.

Gennemalæs venligst denne betjeningsvejledning för brugen.

Läs igenom hela bruksanvisningen innan du börjar använder maskinen.

Vennligst les igjennom hele bruksanvisningen før verktøyet tas i bruk.

Lue Käyttöohjeet huolella ennen laitten käyttöönottoa.

Page 5 of the Panasonic EY6220 user manual — Clutch handle ···(B)
Seite 5 · Zum Vergrößern klicken
Seite 5

Read “Safety Instructions” booklet and the following before using.

OPERATION

Hexagonal driving shaft ···(A)

ADDITIONAL SAFETY RULES

sure to set the main switch lock at the lock position. Select the suitable bit and lightly push it into the hexagonal driving shaft of the main unit. (Refer figure 2) E Refer figure 2 for useable bits.

1. Be aware that this tool is always in an operating condition, since it does not have to be plugged into an electrical outlet.
2. When drilling into walls, floors, etc., “live” electrical wires may be encountered. DO NOT TOUCH THE CHUCK OR ANY FRONT METAL PARTS OF THE TOOL! Hold the tool only by the plastic handle to prevent electric shock in case you drill into a “live” wire.

Clutch handle ···(B)

When using the tool for driving screws into soft material or for terminal screws, etc., there is the possibility of damaging the material or threads if the torque is too high. To compensate for this, the clutch torque may be adjsuted by turning the clutch handle to the required setting.

3. If the bit becomes jammed, immediately turn the main switch off to prevent an overload which can damage the battery pack or motor. Use reverse motion to loosen jammed bits.

Clutch position 1 is the minimum and the clutch torque increases with positions 2, 3, 4, and 5. When the device is set at position 6, the clutch will not slip and the connection to the motor will be direct.

4. During charging, the charger may become slightly warm. This is normal. Do not charge the battery for a long period.
5. Use only a dry, soft cloth for wiping the unit. Do not use a damp cloth, thinner, benzine, or other volatile solvents for cleaning.

during usage, the clutch may not slip even at positions 4 or 5, if this occurs, recharge the battery pack. (Refer figure 3)

6. Wear ear protectors when using the tool for extended periods.

With the switch at off, the bit is locked in place, and the tool can be used as a manual screw- driver. There will be a little play in the driving shaft, but this is not a malfuncton.

with a torque wrench for precise limits as the screw can be damaged. (Refer figure 4)

Bit locking function

Page 6 of the Panasonic EY6220 user manual — Battery pack (EY9021/EY903) ···(F)
Seite 6 · Zum Vergrößern klicken
Seite 6

Main switch (ON/OFF) ···(E)

Battery charger (EY0020/RE503) ···(H)

Push the upper half of the switch for forward ( ) rotation, or the lower half for reverse ( ) rotation. (Refer figure 5)

the first time, or after prolonged storage, charge it for about 24 hours to bring the batteries up to full capacity.

Speed selector switch ···(C)

1. Press the battery pack release button and pull the pack away from the tool. (Refer figure 8) 2. Plug the charger into the power source. 3. Insert the battery pack firmly into the charger. (Refer figure 9) 4. During charging, the charging lamp will be light up. When the charge is completed, an internal electronic switch will automatically be triggered to prevent overcharging. • If the charging lamp does not light, check to determine whether the contacts are clean and the battery pack is inserted completely. 5. When charging is completed, the charging lamp will go out. 6. Avoid charging at temperatures below 0°C above 40°C. 7. After charging has been completed, remove the battery pack from the charger and reinsert it into the tool. (Refer figure 10) 8. If the charging lamp does not turn on immediately afater the chager has been plugged in, or if after 2 hours of charging the lamp does not go off, consult an authorized dealer for checking.

To suit the application of this tool, two different rotational speeds are available. Depending upon use, either the high or low speed should be selected.

LOW200min-1 (RPM)strong torque HIGH400min-1 (RPM)less torque

before operating this tool. (Refer figure 6)

Main switch lock ···(D)

After use, set the main switch lock at the lock position to prevent accidental operation. (Refer figure 7)

Battery pack (EY9021/EY903) ···(F)

1. Press the battery pack release buttons on both sides and pull the pack away from the tool. 2. Carge the battery pack using the battery charger. 3. After the charging has been completed, remove the battery pack from the charger and connect it to the tool. Disconnect the charger from the power source when not in use.

Battery pack life The rechargeable batteries have a limited life. If operation time becomes extremely short after recharging, replace the battery pack with a new one. NOTE: • Use under extremely hot or cold

charged by 15 min. charger EY0202 using adapter EY0890.

  • an engine generator.
  • Do not cover vent holes on the charger.
  • Unplug the charger when not in use.

conditions will reduce operating capacity per charge.

Battery Recycling For environmental protection and recycling of materials, be sure that it is disposed of at an officially assigned location, if there is one in your country.

Page 7 of the Panasonic EY6220 user manual — BATTERY CHARGER (EY0020/RE503)
Seite 7 · Zum Vergrößern klicken
Seite 7

SPECIFICATIONS

CORDLESS DRILL & DRIVER (EY6220/EY503)

Motor DC Motor 2.4 V

No load speed LOW200 min -1 (rpm)
HIGH400 min -1 (rpm)

Hexagonal driving shaft 6.35 mm, (1/4″) across flats

Maximum drilling dia. for metal 2 mm (5/64″)

Maximum torque LOW2.9 Nm (30 kg-cm, 26 in.lbs)
HIGH1.5 Nm (15 kg-cm, 13 in.lbs)

Maximum clutch torque 2.0 Nm (20 kg-cm, 17.5 in.lbs) at 5 position

Overall length 239 mm (9-3/8″)

Weight (with battery pack) 0.4 kg (0.9 lbs)

BATTERY PACK (EY9021/EY903)

Storage battery Ni-Cd battery

Battery voltage 2.4 V DC (1.2 V × 2 cells)

BATTERY CHARGER (EY0020/RE503)

Input 120, 220, 230, 240 V AC separately available

Charging time Standard 1 hour

Mass (Weight) 0.7 kg (1.54 lbs)

catalog.

Page 8 of the Panasonic EY6220 user manual — ELECTRICAL PLUG INFORMATION
Seite 8 · Zum Vergrößern klicken
Seite 8

ONLY FOR U.K.

ELECTRICAL PLUG INFORMATION

are coloured in accordance with the following code: Blue: Neutral Brown: Live As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with the letter E or the Earth Symbol L .

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 3 amp fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 3 amp and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark 7 or the BSI mark 6 on the body of the fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse and fuse cover if it is removable.

This apparatus was produced to BS800.

Fuse Cover

Frage zu Panasonic EY6220 stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Panasonic EY6220

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Panasonic EY6220 PDF-Anleitung

36 Seiten·328 KB·Akkubohrschrauber·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…