DE
Novy logo
Offizielle Bedienungsanleitung

Novy 823

28 Seiten·317 KB·Dunstabzugshaube·PDF·ENITJA
Novy 823
Inhaltsverzeichnis 1 Abschnitte GENERAL INFORMATION AnzeigenAusblenden
Page 1 of the Novy 823 user manual — GENERAL INFORMATION
Seite 1 · Zum Vergrößern klicken
Seite 1

GENERAL INFORMATION

  • Please read these operating instructions carefully. They contain information about installation, operation, safety and maintenance you need to be aware of.
  • This hood is for domestic use only
  • It is recommended to have the installation done by a qualified professional. Any damage due to faulty or unprofessional installation relieves the manufacturer of any form of responsibility.
  • Check the condition of the hood and the installation material before installing. Carefully remove the hood out of the packaging. Be careful not to use sharp knives to open box.
  • Please keep these instructions to pass on to future users.
  • Disposal of transport packaging and old appliance
  • Your new appliance was sent to you in protective packaging. All utilised materials are environmentally safe and recyclable. Please help us by disposing of the packaging in an environmentally friendly manner.
  • Old appliances are not worthless rubbish. Valuable raw materials can be reclaimed by recycling old appliances. This appliance is identified according to the European
  • Directive 2002/96/EC on waste electrical and electronic equipment. Please ask your dealer or inquire at your local authority about current means of disposal.
  • Technical problem In case of technical problems please contact Novy Service Department: Tel. 00 32 56 365 102.
  • Please supply us with the model number of your hood. The model number can be found on the engraved plaque behind the filter. You can make a note of the number here: ……………………………
  • For all remarks or questions which this manual does answer please contact our Customer Service: Tel. 00 32 56 365 101.
Page 2 of the Novy 823 user manual — GENERAL INFORMATION
Seite 2 · Zum Vergrößern klicken
Seite 2
Novy 823 — GENERAL INFORMATION diagram (page 2)
Abb. 1

When using a hood sufficient air flow is necessary. However large your kitchen may be, there is only so much air available in that space. Opening a door or window or the installation a ventilation grid close to the hood insures a good quality of air flow. Insufficient air flow will impair the extraction efficiency of your hood immensely.

① switch on / off ② decrease speed levels ③ and ④ LED indication speed level ⑤ increase speed levels ⑥ illumination

Switch on – switch off To switch the motor on push button ①. The hood will always resume the level it was previously switched off in.

Insufficient air flow can cause reflux from other air ducts such as chimneys or combustion appliances. When using a cooker hood and appliances using energy other than electrical in the same space, the pressure in the room may not surpass 4 Pa (= 0.04mBar).

Switch off with 10 minute delay: Press button ① once. The first green LED blinks, the other LED’s remain lit up according to the level in use. After 10 minutes motor and illumination switch off automatically.

  • Safety
  • Deep frying under the hood is only allowed under constant supervision.
  • Under no circumstances is it allowed to flambé under the hood.
  • In case of fire always switch off the hood.
  • Never extinguish burning fat or oil with water. Cover the pot with a well fitting lid or a burnblanket.

Switch off without delay: Push button ① twice.

Auto-Stop To avoid that the hood will function during a too long period, it will switch off automatically after 3 hours (when no changes to the controls have been made). Only the motor will turn off automatically. The lighting will stay on.

  • Advice For maximum efficiency please follow this advice:
  • When cooking make sure pots are positioned properly under the hood surface.
  • Activate the hood a few minutes prior to cooking.
  • Switch the hood off 10 minutes after cooking is finished (switch off with 10 minute delay).
  • Avoid drafts under the hood surface.
  • When using induction: adapt the intensity of both hob and hood to the lowest possible level in order to avoid excessive creation of damp fumes.

Levels of intensity To decrease speed levels push button ②. To increase speed levels push button ⑤. Three green LED’s ③ indicate level 1 to 3, one red LED ④ indicates the level ‘POWER’.

POWER’ is only used in case of excessive formation of smoke, fumes or odours. Taking into account the large volume of air which is extracted from the room at this level, it’s use should be limited.

‘POWER’ automatically reverts to level 3 after 20 minutes.

Illumination To activate the lights press button ⑥. The lights will switch on at full power. Lighting can be activated independently from the motor.

Dimming (halogen lights only) (Model with Halogen lights) With the halogen lights activated, dim by holding button ⑥ pressed.

Use · Operation

Page 3 of the Novy 823 user manual — GENERAL INFORMATION
Seite 3 · Zum Vergrößern klicken
Seite 3

A self restoring thermocontact switches the motor off in case of overheating. The motor is ready for use when cooled off sufficiently.

Maintenance of the grease filter The hood contains one metal filter which should be cleaned twice a month.

Programming the remote control

The remote control for hood and hob are preinstalled and ready for use. Only when the remote control needs to be reprogrammed (interaction with other controls)act as in the following.

Grease filter indication After 20 cooking hours, the 4 LEDs will start to blink during 5 minutes, this indicates that the grease filter has to be cleaned. When replacing the cleaned filter, you have to reset the hood by pushing the – button during 5 seconds . If you don’t reset, the LED lights will continu blinking.We advise you to clean your filter twice a month for an optimal operation.

Determine the code used: Simultaneously press on/off + the key with the sun. The lamp flashes as well as the selected code (there are 10 code options in total).

Access to the filter Take hold of the right and left side of the plate (a) and pull down simultaneously. Remove the filter (b) by taking hold of its hook and pulling down.

Change the codea. Simultaneously press on/off + the key with

the sun for 3 seconds until the lamp is flash- ing. After this the lamp as well as the selected code will flash. Repeat this step until you have reached the required code (there are 10 code options in total). b. Simultaneously press + lamp of the roof cover

Novy 823 — GENERAL INFORMATION diagram (page 3)
Abb. 2

control until the second green LED is blinking. c. Press the key with the sun on the remote con-

trol within 10 seconds to confirm the settings. The cooker hood and the remote control are now in line with each other.

  • Cleaning the filter:
  • in the dishwasher
  • manually: in a hot solution of water and a liquid detergent. Rince and allow to dry completely
  • Change the batteries:
  • For changing the batteries unscrew the plastic cover, remove the old batteries and insert the new ones. Pay attention to the polarity marking given in the battery compartment (figure 4).
  • Empty batteries are not to be disposed of in the household refuse, but they are to be handed in as chemical waste.

NOVY key: You can switch on the ambient lighting using the NOVY key (figure 5).

The stainless steel surfaces can be treated with Novy Inoxcleaner (906.060) after cleaning.

Technical information: - Power supply: (2xAAA) batteries - Frequence: 433.92Mhz - Numbre of codes: 10 - Worktemperature: 0-50°C - Dimensions: 110 x 50 x 19mm

Maintenance

Page 4 of the Novy 823 user manual — GENERAL INFORMATION
Seite 4 · Zum Vergrößern klicken
Seite 4

Please allow the lights to cool down sufficiently before touching them. Cover and protect delicate surfaces underneath the hood when changing lamps

Electrical output: electrical cord + plug with ground. To be plugged into socket with ground. Check for compatibility with information on type plate (behind filter). Socket must be within reach. Changes or replacement of the electrical cord should be performed by a professional only.

  • Replace the lamps:
  • attach the suction device to the lamp
  • pull towards you
  • put a new lamp in place using the same suction device
Novy 823 — GENERAL INFORMATION diagram (page 4)
Abb. 3

The hoods have 2 lamps of the following type: 12V/20W/Ø35/GU4/38° (order number 7401.029). Total energy consumption with lightning: 810, 811: 210 W 820, 821: 380 W

Replacing the lamps · Electrical connection

Frage zu Novy 823 stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Novy 823

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Novy 823 PDF-Anleitung

28 Seiten·317 KB·Dunstabzugshaube·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…