


When using a hood sufficient air flow is necessary. However large your kitchen may be, there is only so much air available in that space. Opening a door or window or the installation of a ventilation grid close to the hood insures a good quality of air flow. Insufficient air flow will impair the extraction efficiency of your hood immensely.
① switch on / off ② decrease speed levels ③ increase speed levels ④ illumination ⑤ and ⑥ LED indication speed level
Insufficient air flow can cause reflux from other air ducts such as chimneys or combustion appliances. When using a cooker hood and appliances using energy other than electrical in the same space, the pressure in the room may not surpass 4 Pa (= 0.04mBar).
Switch on – switch off To switch the motor on push button ①. The hood will always resume the level it was previously switched off in.
Switch off with 10 minute delay: Press button ① once. The first green LED blinks, the other LED’s remain lit up according to the le- vel in use. After 10 minutes motor and illumination switch off automatically.
Switch off without delay: Push button ① twice.
Auto-Stop To avoid that the hood will function during a too long period, it will switch off automatically after 3 hours (when no changes to the controls have been made). Only the motor will turn off automa- tically. The lighting will stay on.
Levels of intensity To decrease speed levels push button ②. To in- crease speed levels push button ③.Three green LED’s ⑤ indicate level 1 to 3, one red LED ⑥ indi- cates the level ‘POWER’.
‘POWER’ is only used in case of excessive for- mation of smoke, fumes or odours. Taking into account the large volume of air which is extrac- ted from the room at this level, it’s use should be limited.
‘POWER’ automatically reverts to level 3 after 10 minutes.
A self restoring thermocontact switches the mo- tor off in case of overheating. The motor is ready for use when cooled off sufficiently.
Use

Illumination To activate the lights press button ④. The lights will switch on at full power. Lighting can be activated independently from the motor.
OPTION: kit for remote control (InTouch) Optionally, there is a kit for a remote control available which must also be installed if you se- lect InTouch. If you have a Novy induction hob with the InTouch function, you can operate all of the functions of the extraction hood via the in- duction hob with the optional kit. This kit must be mounted during the installation and exclusively by an authorized installer.
Recirculation (option) If you have chosen for recirculation, please follow the instructions below.
Cleaning indication: The red LED will light up after 200 working hours (time to regenerate the used carbon filter).
Maintenance of the grease filter The hood contains two metal filters which should be cleaned twice a month.
Grease filter indication After 20 cooking hours, the 4 LEDs will start to blink during 5 minutes, this indicates that the grease filter has to be cleaned. When replacing the cleaned filter, you have to reset the hood by pushing the – button during 5 seconds . If you don’t reset, the LED lights will continu blinking. We advise you to clean your filter twice a month for an optimal operation.
Access to the filter Take hold of the right and left side of the plate (A) and pull towards you simultaneously. Remove the filter (B) by taking hold of its hook and pulling down.
Reprogramming: Press + and – simultaneously for 5 seconds, the red LED flashed 3 times for confirmation (if this programming is not done, the program will be set automatically after having switched on the device 10 times).

Deactivate the program: Simultaneously press + and – for 5 sec. until the third green LED flashes 3 times.
Maintenance of the hood Please allow the lights to cool down sufficiently before cleaning the hood. Use a soft, wet cloth and a mild detergent to clean the hood. Never use aggressive, abrasive detergents or sponges. Bleach will damage stainless steel. The stainless steel surfaces can be treated with Novy Inoxclea- ner (906.060) after cleaning.

Replacement of the led ligths
In the event of a malfunction, you can contact your (kitchen) supplier and/or the Novy Customer Service Department. In order for the Customer Service Department to reply quickly and precise- ly you must to tell them which type of extraction hood you have. The model number can be found on a sticker on the interior of the extraction hood. This is visible as soon as you take the filter out of the extraction hood. You can write down the model number here: Model number:
electrical output: electrical cord + plug with ground. To be plugged into socket with ground. Check for compatibility with information on type plate (behind filter). Socket must be within reach. Changes or replacement of the electrical cord should be performed by a professional only.
Electrical connection

Afmetingen - Dimensions - Abmessungen - Dimensions


7810 - 7811 · 7820 - 7821


Elektrisch schema - Schéma électrique - Elektrischer Schaltplan - Electrical scheme
6 GE/GN 5 BL 4 ZW 3 GS 2 RD 1 WT




Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.