DE
Novy logo
Offizielle Bedienungsanleitung

Novy 7507

36 Seiten·481 KB·Dunstabzugshaube·PDF·ENITJA
Novy 7507
Inhaltsverzeichnis 1 Abschnitte GENERAL INFORMATION AnzeigenAusblenden
Page 1 of the Novy 7507 user manual — GENERAL INFORMATION
Seite 1 · Zum Vergrößern klicken
Seite 1

GENERAL INFORMATION

  • Please read these operating instructions carefully. They contain information about installation, operation, safety and maintenance you need to be aware of.
  • This hood is for domestic use only
  • It is recommended to have the installation done by a qualified professional. Any damage due to faulty or unprofessional installation relieves the manufacturer of any form of responsibility.
  • Check the condition of the hood and the installation material before installing. Carefully remove the hood out of the packaging. Be careful not to use sharp knives to open the box.
  • Please keep these instructions to pass on to future users.
  • Disposal of transport packaging and old appliance Your new appliance was sent to you in protective packaging. All utilised materials are environmentally safe and recyclable. Please help us by disposing of the packaging in an environmentally friendly manner. Old appliances are not worthless rubbish. Valuable raw materials can be reclaimed by recycling old appliances. This appliance is identified according to the European Directive 2002/96/EC on waste electrical and electronic equipment. Please ask your dealer or inquire at your local authority about current means of disposal.
  • Technical problem In case of technical problems please contact Novy Service Department: For Belgium: Tel.: 056/36.51.02 For France: Tel.: 03.20.94.06.62 For Germany: Tel.: 0511.54.20.771 For all other countries: your local installor or Novy Belgium: +32 (0)56/36.51.02 Please supply us with the model number of your hood. The model number can be found on the engraved plaque behind the filter. You can make a note of the number here: ……………………………
  • For all remarks or questions to which this manual doesn’t answer please contact our Customer Service: For Belgium: Tel.: 056/36.51.01 For France: Tel.: 03.20.94.06.62 For Germany: Tel.: 0511.54.20.771 For all other countrys: your local installor or Novy Belgium: +32 (0)56/36.51.02
Page 2 of the Novy 7507 user manual — GENERAL INFORMATION
Seite 2 · Zum Vergrößern klicken
Seite 2
Novy 7507 — GENERAL INFORMATION diagram (page 2)
Abb. 1

When using a hood sufficient air flow is necessary. However large your kitchen may be, there is only so much air available in that space. Opening a door or window or the installation of a ventilation grid close to the hood insures a good quality of air flow. Insufficient air flow will impair the extraction efficiency of your hood immensely.

① switch on / off ② decrease speed levels ⑤ and ⑥ LED indication speed level ③ increase speed levels ④ illumination

Insufficient air flow can cause reflux from other air ducts such as chimneys or combustion appliances. When using a cooker hood and appliances using energy other than electrical in the same space, the pressure in the room may not surpass 4 Pa (= 0.04mBar).

Switch on - switch off To switch the motor on push button ①. The hood will always resume the level it was previously switched off in.

Switch off with 10 minute delay: Press button ① once. The first green LED blinks, the other LED’s remain lit up according to the level in use. After 10 minutes motor and illumination switch off automatically.

  • Safety
  • Deep frying under the hood is only allowed under constant supervision.
  • Under no circumstances is it allowed to flambé under the hood.
  • In case of fire always switch off the hood.
  • Never extinguish burning fat or oil with water. Cover the pot with a well fitting lid or a burnblanket.

Switch off without delay: Push button ① twice.

Auto-Stop To avoid that the hood will function during a too long period, it will switch off automatically after 3 hours (when no changes to the controls have been made). Motor and lighting will turn off automatically.

  • Advice For maximum efficiency please follow this advice:
  • When cooking make sure pots are positioned properly under the hood surface.
  • Activate the hood a few minutes prior to cooking.
  • Switch the hood off 10 minutes after cooking is finished (use delay function when present).
  • Avoid drafts under the hood surface.
  • When using induction: adapt the intensity of both hob and hood to the lowest possible level in order to avoid excessive creation of damp fumes.

The ambient lighting will stay activated.

Levels of intensity To decrease speed levels push button ②. To increase speed levels push button ③. Three green LED’s ⑤ indicate level 1 to 3, one red LED ⑥ indicates the level ‘POWER’.

‘POWER’ is only used in case of excessive formation of smoke, fumes or odours. Taking into account the large volume of air which is extracted from the room at this level, it’s use should be limited.

‘POWER’ automatically reverts to level 3 after 20 minutes.

Illumination To activate the lights press button ④. The lights will switch on at full power. Lighting can be activated independently from the motor. Dimming halogen lights

Use · Operation

Page 3 of the Novy 7507 user manual — GENERAL INFORMATION
Seite 3 · Zum Vergrößern klicken
Seite 3

With the halogen lights activated, dim by holding button ④ pressed. A self restoring thermocontact switches the motor off in case of overheating. The motor is ready for use when cooled off sufficiently.

Ambient lighting Press the on/off button for 3 seconds and the ambiant lighting will start.

1 2 3 4 5

Programming the remote control

Maintenance of the grease filter The hood contains one metal filter which should be cleaned twice a month.

The remote control for hood and hob are pre- installed and ready for use. Only when te remote control needs to be reprogrammed (interaction with other controls)act as in the following.

Grease filter indication After 20 cooking hours, the 4 LEDs will start to blink during 5 minutes, this indicates that the grease filter has to be cleaned. When replacing the cleaned filter, you have to reset the hood by pushing the – button during 5 seconds . If you don’t reset, the LED lights will continu blinking.We advise you to clean your filter twice a month for an optimal operation.

Determine the code useda. Simultaneously press

the key with the sun. The lamp flashes as well as the selected code (there are 10 code options in total) (figure 1).

Change the codea. Simultaneously press

the key with the sun for 3 seconds until the lamp is flashing. After this the lamp as well as the selected code will flash. Repeat this step until you have reached the required code (there are 10 code options in total) (figure 1). b. Simultaneously press

Access to the filter

Novy 7507 — GENERAL INFORMATION diagram (page 3)
Abb. 2

lamp of the roof cover control until the second green LED is blinking (figure 2). c. Press the

key with the sun on the remote control within 10 seconds to confirm the settings. The cooker hood and the remote control are now in line with each other (figure 3).

Take hold of the right and left side of the plate (a) and pull down simultaneously. Remove the filter (b) by taking hold of its hook and pulling down.

  • Change the batteries:
  • For changing the batteries unscrew the plastic cover, remove the old batteries and insert the new ones. Pay attention to the polarity marking given in the battery compartment (figure 4).
  • Empty batteries are not to be disposed of in the household refuse, but they are to be handed in as chemical waste.
  • Cleaning the filter:
  • in the dishwasher
  • manually: in a hot solution of water and a liquid detergent. Rince and allow to dry completely Important! The previous instructions need to be followed. If not an increased fire hazard may occur.

NOVY key: • You can switch on the ambient lighting using the NOVY key (figure 5).

Maintenance of the monoblock filter Only use the original Novy monoblock filter (7300.055). After 200 cooking hours the filter needs to be reactivated. To do so, place the filter during one hour in an electrical oven on 120°C. The filter can be reactivated 12 times. The hood can be programmed so that a signal is given when the 200 cooking hours are reached. The monoblock filters are placed behind the grease filter

Technical information: - Power supply: (2xAAA) batteries - Frequence: 433.92Mhz - Numbre of codes: 10 - Worktemperature: 0-50°C - Dimensions: 110 x 50 x 19mm

Show 4 more labels / short text on this page
Maintenance · on/off + · on/off + · +
Page 4 of the Novy 7507 user manual — GENERAL INFORMATION
Seite 4 · Zum Vergrößern klicken
Seite 4
  • Click the cover plate (A) loose with a light descending push.
  • When you want to replace the cover plate (A) don’t forget to replace the adjusting clips over the plugs and to tighten the screws.

Programming the saturation indication (Attention! Programming can only take place when the hood is switched off)

  • push + and - at the same time, during 5 min.. (the red led will blink 5 times)
  • delay time is programmed for 30 minutes (instead of 10 min.).
  • the saturation indication is programmed (200 working hours).

Remove the grease filter • Remove the grease filter to get acces to the screws witch hold the glass panels (see main- tenance).

Remove the glass panels

After 200 working hours the red LED will blink (time to reactivate the monoblock filter)

Novy 7507 — GENERAL INFORMATION diagram (page 4)
Abb. 3
  • Reprogramming of the saturation indication. (Attention! Programming can only take place when the hood is switched off)
  • push + and - at the same time, during 5 min.. (the red led will blink 5 times) or automatically after pressing 10 times the on/off button 0/I Deactivating the saturation indication (Attention! Programming can only take place when the hood is switched off)
  • push + and - at the same time, during 5 min.. (the 3rd green LED will blink 5 times)
  • Loosen First the screws before you remove the glass panels (A).
  • Tip the glass panel (A) over the filterholder (B)
  • Watch out: Support the glass panel with the integrated command, so the cable (C) that lies underneath doens’t get damaged.

Maintenance of the hood Please allow the lights to cool down sufficiently before cleaning the hood. Use a soft, wet cloth and a mild detergent to clean the hood. Never use aggressive, abrasive detergents or sponges. Bleach will damage stainless steel. The stainless steel surfaces can be treated with Novy Inoxcleaner (906.060) after cleaning.

  • Cleaning the glass panels and cover plate
  • Don’t put the panels and the cover plate in the dishwasher and don’t plunge them in water completely.
  • Keep the control dry while cleaning the glass panel.

Replacement of the fluorescent lighting Remove first the electrical plug from the electrical point.

Replacement of the lights

Novy 7507 — GENERAL INFORMATION diagram (page 4)
Abb. 4
Novy 7507 — GENERAL INFORMATION diagram (page 4)
Abb. 5
  • Turn the fluorescent lights with a quarter turn to take it out of its support.
  • Place the new light in its support and turn again with a quarter turn until you hear a clicking sound.
  • Remove the cover plate
  • Open the cover plate (A) by pulling it down.
  • Remove the cover plate (A) by converting the adjusting clips (B). Don’t loosen the screws completely!

Model 7505-7507 Novy reference 898.025 Reference lamp T8 F25W/33”/840

Page 5 of the Novy 7507 user manual — GENERAL INFORMATION
Seite 5 · Zum Vergrößern klicken
Seite 5

Replacement of the starter

Novy 7507 — GENERAL INFORMATION diagram (page 5)
Abb. 6
Novy 7507 — GENERAL INFORMATION diagram (page 5)
Abb. 7

Use the suction device to open the covers

Novy 7507 — GENERAL INFORMATION diagram (page 5)
Abb. 8
  • If needed turn the light out withe a quarter turn to take it out of its support.
  • Turn the starter with a quarter turn to take it out.
  • Place the new starter in its support and turn with a quarter turn.
  • The starter is installed correctly when you here a soft clicking sound.
  • Place the remplacement lamp in the support and turn this with a quarter turn until you here a soft clicking sound.
  • 7505-7507 has both 2 starters from the type: OSRAM St 111 / Novy reference 804-016

Turn the lamp a quarter (1). Push it to the front, until it comes out of the holder. (2). Pull the lamp to the top.(3)

  • Back to the start initial position
  • Tighten everything again to the initial position.
  • IMPORTANT! When the glass panel (A) is placed back, the glass panel has to be pushed over the filterholder so its fixed (fig. 3.3).
  • Place the greasse filter back in its support
  • Install the cover plate, don’t forget to slide de adjustements clips over the plugs and tighten the cover plate again.
  • The unit is ready for installation.
Novy 7507 — GENERAL INFORMATION diagram (page 5)
Abb. 9

Electrical connection The hood is equipped with a electric flex with standard plug and has to be connected with an electric socket with grounding. When you install you need to make sure that it is easy reachable. The replacement of the electric flex has to be done by an approved installer. The amperage and the consumption are marked on the information sticker in the inside of the hood.

The ambient lighting contains 2 TL mini lamps of 8W (order number 7500034) and 2 TL T5 lamps of 21W (order number 7500035).

Electrical output: electrical cord. Changes or replacement of the electrical cord should be performed by a professional only.

Lamps of the ambient lighting

Unscrew the screws on top of the structure

Dimensionsp. 30 Electrical scheme: p. 31

Electrical connection

Frage zu Novy 7507 stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Novy 7507

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Novy 7507 PDF-Anleitung

36 Seiten·481 KB·Dunstabzugshaube·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…