


When using a hood sufficient air flow is necessary. However large your kitchen may be, there is only so much air available in that space. Opening a door or window or the installation of a ventilation grid close to the hood insures a good quality of air flow. Insufficient air flow will impair the extraction efficiency of your hood immensely.
① switch on / off ② decrease speed levels ⑤ and ⑥ LED indication speed level ③ increase speed levels ④ illumination
Insufficient air flow can cause reflux from other air ducts such as chimneys or combustion appliances. When using a cooker hood and appliances using energy other than electrical in the same space, the pressure in the room may not surpass 4 Pa (= 0.04mBar).
Switch on - switch off To switch the motor on push button ①. The hood will always resume the level it was previously switched off in.
Switch off with 10 minute delay: Press button ① once. The first green LED blinks, the other LED’s remain lit up according to the level in use. After 10 minutes motor and illumination switch off automatically.
Switch off without delay: Push button ① twice.
Auto-Stop To avoid that the hood will function during a too long period, it will switch off automatically after 3 hours (when no changes to the controls have been made). Motor and lighting will turn off automatically.
The ambient lighting will stay activated.
Levels of intensity To decrease speed levels push button ②. To increase speed levels push button ③. Three green LED’s ⑤ indicate level 1 to 3, one red LED ⑥ indicates the level ‘POWER’.
‘POWER’ is only used in case of excessive formation of smoke, fumes or odours. Taking into account the large volume of air which is extracted from the room at this level, it’s use should be limited.
‘POWER’ automatically reverts to level 3 after 20 minutes.
Illumination To activate the lights press button ④. The lights will switch on at full power. Lighting can be activated independently from the motor. Dimming halogen lights
Use · Operation

With the halogen lights activated, dim by holding button ④ pressed. A self restoring thermocontact switches the motor off in case of overheating. The motor is ready for use when cooled off sufficiently.
Ambient lighting Press the on/off button for 3 seconds and the ambiant lighting will start.
1 2 3 4 5
Programming the remote control
Maintenance of the grease filter The hood contains one metal filter which should be cleaned twice a month.
The remote control for hood and hob are pre- installed and ready for use. Only when te remote control needs to be reprogrammed (interaction with other controls)act as in the following.
Grease filter indication After 20 cooking hours, the 4 LEDs will start to blink during 5 minutes, this indicates that the grease filter has to be cleaned. When replacing the cleaned filter, you have to reset the hood by pushing the – button during 5 seconds . If you don’t reset, the LED lights will continu blinking.We advise you to clean your filter twice a month for an optimal operation.
the key . The lamp flashes as well as the selected code (there are 10 code options in total) (figure 1).
the key for 3 seconds until the lamp is flashing. After this the lamp as well as the selected code will flash. Repeat this step until you have reached the required code (there are 10 code options in total) (figure 1). b. Simultaneously press
Access to the filter Take hold of the right and left side of the plate (a) and pull down simultaneously. Remove the filter (b) by taking hold of its hook and pulling down.
until the second green LED is blinking (figure 2). c. Press the

key on the remote control within 10 seconds to confirm the settings. The cooker hood and the remote control are now in line with each other (figure 3).
NOVY key: • You can switch on the ambient lighting using the NOVY key (figure 5).
Technical information: - Power supply: (2xAAA) batteries - Frequence: 433.92Mhz - Numbre of codes: 10 - Worktemperature: 0-50°C - Dimensions: 110 x 50 x 19mm
Maintenance of the monoblock filter Only use the original Novy monoblock filter (7300.055). After 200 cooking hours the filter needs to be reactivated. To do so, place the filter during one hour in an electrical oven on 120°C. The filter can be reactivated 12 times. The hood can be programmed so that a signal is given when the 200 cooking hours are reached.

The monoblock filters are placed behind the grease filter
Please allow the lights to cool down sufficiently before touching them. Cover and protect delicate surfaces underneath the hood when changing lamps.
Programming the saturation indication (Attention! Programming can only take place when the hood is switched off)
The hood has 2 lamps of the following type: 12V/20W/Ø35/GU4/38°
After 200 working hours the red LED will blink (time to reactivate the monoblock filter)

Maintenance of the hood Please allow the lights to cool down sufficiently before cleaning the hood. Use a soft, wet cloth and a mild detergent to clean the hood. Never use aggressive, abrasive detergents or sponges. Bleach will damage stainless steel. The stainless steel surfaces can be treated with Novy Inoxcleaner (906.060) after cleaning.
Replacing the lamps

Lamps of the ambient lighting
Unscrew the screws on top of the structure
Electrical output: electrical cord. Changes or replacement of the electrical cord should be performed by a professional only.

Use the suction device to open the covers

Turn the lamp a quarter (1). Push it to the front, until it comes out of the holder. (2). Pull the lamp to the top.(3)

The ambient lighting contains 2 TL mini lamps of 8W (order number 7500034) and 2 TL T5 lamps of 21W (order number 7500035).
Electrical connection
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.