

There is an operating display on the front side of the hood. Explanation of operating buttons:
1 2 3 4 5 6
When using a hood sufficient air flow is necessary. However large your kitchen may be, there is only so much air available in that space. Opening a door or window or the installation of a ventilation grid close to the hood insures a good quality of air flow. Insufficient air flow will impair the extraction efficiency of your hood immensely.

Switch the fan on and off This key ⑥ is for switching the fan on and off.
Fan position These keys ③ ⑤ are for decreasing or increasing the fan position. This hood has four speeds.
Insufficient air flow can cause reflux from other air ducts such as chimneys or combustion appliances. When using a cooker hood and appliances using energy other than electrical in the same space, the pressure in the room may not surpass 4 Pa (= 0.04mBar).
Display The display ④ shows the active fan position.
Timer The hood has a timer. Press this key ② once to switch off the hood and enable the run-out time. Now a run-out time of about 10 minutes starts. The activated fan position will now flash on the display. The motor and the lighting are switched off after about 10 minutes. If you no longer want to make use of the run-out time, press the timer key again to disable the run- out time.
Lighting This key ① is for switching the lighting on and off. The lighting can be used at any moment, also when the fan has been switched off. Other information The hood has a doubly drawing in centrifugal fan with ball bearings, which ensures vibration-free operation. The built-in lighting has been installed such, that the entire surface of the cooking plate is evenly lighted. A self-controlled thermal contact in the motor makes sure that the motor is switched off when overheated. The motor will switch on again after is has cooled down. The cause of the overheating is still to be determined, though. This may have been cause by, for example, the contents of the pan catching fire, because on object is blocking the fan in the fan housing or because the exhaust outlet is partly or fully blocked.
Use · Operation

Side exhaust The hood has been equipped with side exhaust. This means that the extraction is concentrated on the side of the hood. This creates a higher air speed on the sides, which leads to more efficient extraction.
Replacement of the lamps First remove the plug from the socket or turn off the electricity. Wait until the lamp has cooled down before replacing it. The cooker hood has four halogen spots from each 20 Watt. The halogen spots can be replaced by putting a little screwdriver in the interstice of the rim around the spot. Now press the rim (A) carefully downwards with the point of the screwdriver. The little glass (B) comes out of the spot.
Maintenance of the grease filter The hood contains one or 2 metal filters (according to the model) which should be cleaned twice a month.

Grease filter indication After 30 cooking hours, the vertical line in the middel will start to blink during 30 seconds, this indicaties that the grease filter has to be cleaned. When replacing the cleaned filter, you have to reset the hood by pushing the timer button during 5 seconds.
The halogen can now be removed out of the spot. Be careful that the lamp doesn’t fall down immediately, so it’s advisable to put something on your hob in order to protect it. Don’t touch the new halogen with your hands, this reduces the light output. Replace the defective lamp by a new one from the same type and same power (20 Watt). Then reassemble the glass and the rim back into the spot.
Access to the filter Take hold of the right and left side of the plate (a) an pull down simultaneously. Remove the filter (b) by pushing simultaniously on the 2 fastners.

The hood has a cable with earthed plug and must be connected to an earthed wall socket. Amperage and absorption are shown on the specification label on the inside of the hood. The plug must be easily accessible. Replacement of the connection cable is to be done by a qualified installer.
Maintenance of the hood Please allow the lights to cool down sufficiently before cleaning the hood. Use a soft, wet cloth and a mild detergent to clean the hood. Never use aggressive, abrasive detergents or sponges. Bleach will damage stainless steel. The stainless steel surfaces can be treated with Novy Inoxcleaner (906.060) after cleaning.
Maintenance · Electrical connection
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.