
Carefully read the instructions before installing and using the equipment. The manufacturer is not liable for improper installation and use of the equipment that may cause injuries and damage. Always keep the instructions at hand, so they can be easily referred to during use.
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they are given supervision or instructions concerning how to use the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Keep packaging materials away from children. Keep children away from the appliance during operation or when cooling. Cleaning and maintenance should not be done by children without supervision.
During installation, follow the instructions supplied separately Only qualified personnel can install the appliance and replace the cable. WARNING: The appliance and its accessible parts become hot during use. Care
should be taken to avoid touching heating elements. Children less than 8 years of age shall be kept away unless continuously supervised. During use the appliance becomes hot. Care should be taken to avoid touching
heating elements inside the oven. WARNING: Accessible parts may become hot during use. Young children should
be kept away. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven
door glass since they can scratch the surface, which may result in shattering of the glass. Do not use steam cleaners to clean the appliance. Do not use abrasive detergents or metal scrapers to clean the appliance. The electric connection is made via an omnipolar switch, which is suitable for the
intensity to be tolerated and which has a minimum gap of 3mm between its contacts, which will ensure disconnection in case of emergency or when cleaning the crockery warmer. If a plug is used for the electric connection, then it must be accessible after installation. The connection should include correct earthing, in compliance with current norms.
Disconnect the appliance from the power supply before carrying out any maintenance operation.

WARNING!
Before connecting the appliance compare the power data (voltage and frequency) indicated on the characteristics plate with those of the power supply in question. If these data do not match there may be problems. In case of doubt, contact an electrician.
Repairs and maintenance, especially of parts carrying electrical current, must only be done by technicians authorised by the manufacturer. The manufacturer and retailers do not accept responsibility for any damaged caused to people, animals or property as a result of repairs and maintenance carried out by non- authorised personnel.
If the electrical wire plug is removed, the appliance must be installed and connected by a technician. Contact a qualified electrician who knows and respects current safety standards. The manufacturer cannot be held responsible for damage resulting from fitting or connecting errors.
Repairs undertaken during the guarantee period must only be done by technicians authorised by the manufacturer. If this is not the case then any damage resulting from the repair in question is excluded from the guarantee
The electrical safety of the appliance can only be guaranteed if it is earthed. The manufacturer cannot be held responsible for damage resulting from the absence of or defects in the installation’s protection system (e.g. electrical shock).
The appliance must be disconnected from the electrical current when installation and repair work is being done. To disconnect the appliance from the current, one of the following conditions must apply:
Only use the appliance once it has been fitted into its built-in position. Only in this manner can it be guaranteed that users cannot access the electrical components.
Never open up the appliance’s frame. Possible contacts with electrical conducting parts or changes to electrical or mechanical components may represent a danger to users’ safety and prejudice the correct working of the appliance.

This appliance complies with current safety
Do not use the appliance to heat up the air
standards. Improper use of the appliance may put the user at risk. Read the operating instructions carefully before
temperature in the kitchen. The high temperatures reached may cause easily inflammable objects close to the appliance to catch fire. Do not use high pressure or steam jet cleaning
using the appliance for the first time. In this way you will avoid the risk of injuring yourself or damaging the appliance. Depending on the temperature selected and
devices. The steam may affect electrical components and cause a short circuit. The steam pressure may also cause damage to the appliance’s surface and components in the long term. When you stop using the appliance at the end
the operating time, the temperature inside the appliance may reach 80 ºC. To take crockery out of the crockery warmer protect your hands by using oven gloves or an oven cloth. Do not sit or hang on the drawer. The
of its working life, disconnect it from the power supply and render the electrical cable unusable so that the appliance is not a danger if, for example, children use it for playing.
telescopic runners will be damaged. The maximum load capacity of the drawer is 25 kg. Do not store synthetic containers or easily
inflammable objects inside the crockery warmer. When you switch on the appliance such containers and objects may melt or catch fire. Fire danger!


This appliance is equipped with a warm air circulation system. A fan distributes the heat generated by an electrical heating element throughout the interior of the appliance.
The circulating hot air that is generated heats up the crockery quickly and evenly.
A metal grille protects both the heating element and the fan.
The thermostat allows the user to define and control the temperature wanted for the crockery.
The base of the drawer is fitted with a non-slip mat to prevent plates and dishes sliding around when the drawer is opened and closed.

Before using the appliance for the first time you should clean the interior and the exterior, following the cleaning instructions given in the section “Cleaning and Maintenance”.
Make sure the kitchen is well-ventilated when you are doing this.
The appliance’s parts are protected by a special product. For this reason, during the first heating an odour will be released. Both the odour and any smoke that may form will disappear after a short time and neither signifies that there is anything wrong with the connection or the appliance.
Then heat the warming drawer for at least 2 hours. For this, set the temperature to the maximum position.


In this mode the whole system is disconnected and no indicator light or display is lit. Normal Operation
The programming can be cancelled at any time by pressing the “-” key for 3 seconds.
In this mode the system is generating heat. The display shows the remaining operating time and the set temperature alternating each 2 seconds. The Timer and Temperature indicator lights light- up alternating each 2 seconds and coordinated with the display indication. The Operation indicator light is illuminated continuously until the Timer reaches zero.
The operation or the delayed start can be cancelled (for example, because a guest arrived earlier or the crockery seems warm enough) by pressing the “-” key for 3 seconds.
To program the normal operation, proceed as follows: 1. Press the “M” key once or several times until the Timer indicator light is flashing. 2. Press the “+” or “-” keys to set the desired operation time in the range 0h00 – 4h00. 3. Press the “M” key to validate. The Temperature indicator light starts to flash. 4. Press the “+” or “-” keys to set the desired temperature in the range 30 – 80ºC. 5. When the desired temperature starts to blink, press the “M” key for 3 seconds or wait 5 seconds. 6. The Warming Drawer starts to operate with the set parameters. Delayed Start
Various factors affect heating times:
Material and thickness of the crockery Load quantity How the crockery is arranged Temperature setting
It is therefore not possible to give any precise heating times.
However, as a guide, the following times are given for the thermostat setting of 60ºC and for uniform heating of the crockery:
Crockery for 6 people 30 – 35
As you use the warming drawer more and more you will learn the best settings for your crockery.
In this mode the Display shows the remaining time for the operation to start and counting-down. The Operation indicator light will blink and the Delayed Start indicator is illuminated.
To set a delayed start, proceed as follows: 1. Program the normal operation parameters as in points 1) to 4) of the previous section. 2. Press the “M” key to validate. The Delayed Start indicator light starts to flash. 3. Press the “+” or “-” keys to set the desired start delay in the range 0h00 – 9h50. 4. When the desired start delay starts to blink, press the “M” key for 3 seconds or wait 5 seconds. 5. The Warming Drawer enters the Delayed Start mode.
Load Time (min)

Load capacity depends on the size of the crockery items.
6 x 24cm Dinner Plates
6 x 10cm Soup Bowls
1 x 19cm Serving Dish
1 x 17cm Serving Dish
1 x 32cm Meat Plates
20 dishes with 28 cm
80 espresso coffee cups


Cleaning and Maintenance
Cleaning is the only maintenance action that is required normally.
Clean the inside of the warming drawer regularly using a damp cloth. If it is very dirty add a few drops of washing-up liquid to the washing water.
Wipe the surfaces dry using a dry cloth.
Avoid water entering through the air circulation opening.
Do not use aggressive or abrasive cleaning products, abrasive sponges or pointed objects since stains or abrasion marks may appear.
Only use the warming drawer again when it is completely dry.
Do not use high pressure or steam jet cleaning appliances.
The non-slip surface mat can be removed to facilitate cleaning of the drawer.
The mat can be cleaned by hand using hot water with a few drops of washing-up liquid.
The warming drawer can be cleaned using just a damp cloth. If it is very dirty, add a few drops of washing-up liquid to the washing water.
Dry thoroughly.
Wipe the surfaces dry using a dry cloth.
The non-slip mat should only be replaced when it is completely dry.
For stainless steel fronted warming drawers, special products for treatment of stainless steel surfaces can be used. These products prevent the surfaces becoming dirty again for some time. Apply a thin layer of such a product on the surface using a soft cloth.
On aluminium fronted warming drawers use a gentle glass cleaning product and a soft cloth that does not release fluff. Wipe horizontally without pressing on the surface since aluminium is sensitive to scratches and cuts.

The crockery doesn’t heat up at all. Check
whether:
- You can hear the noise of a fan. If the fan is operating then the heating element is broken; if the fan is not operating then the fan is broken.
Before contacting Technical Assistance, check on the following:
The crockery doesn’t heat up enough.
- The switchboard fuses / circuit breakers
Check whether:
have fused / tripped out.
- The appliance has been switched on.
- The appropriate temperature has been
The crockery is heating up too much.
selected.
- The temperature selector is broken.
- The air circulation orifices are covered by the
crockery.
The on/off switch does not light up.
- The crockery was left to heat up for sufficient
- The switch’s pilot light has blown.
time.
Heating time depends on several factors, such as, for example:
- Crockery material type and thickness.
- Quantity of crockery.
- How the crockery is arranged.

should not be put into the normal systems for disposal of solid urban waste.
Disposal of the packaging
Outdated appliances should be collected separately to optimise component material recovery and re-cycling rates and to prevent potential harm to human health and the environment. The symbol of a rubbish container superimposed by a diagonal cross should be put on all such products to remind people of their obligation to have such items collected separately.
The packaging bears the Green Point mark.
Dispose of all the packaging materials such as cardboard, expanded polystyrene and plastic wrapping in the appropriate bins. In this way you can be sure that the packaging materials will be re-used.
Consumers should contact their local authorities or point of sale and request information on the appropriate places to leave their old home electrical appliances. Before disposing of your appliance, render it non- usable by pulling out the power cable, cutting this and disposing of it
Disposal of equipment no longer used
According to European Directive 2002/96/EC on the management of waste electrical and electronic equipment (WEEE), home electrical appliances

Check that the input voltage indicated on the characteristics plate is the same as the voltage of the power outlet you are going to use.

Open the drawer and take out all the accessories and remove the packing material.
Make sure that the warming drawer is not damaged in any way. Check that the drawer opens and closes correctly. If you find any damage, contact the Technical Assistance Service.
The warming drawer should only be built-in in combination with those appliances indicated by the manufacturer. If it is fitted in combination with other appliances, the guarantee is no longer valid since it is impossible to guarantee that the warming drawer will work correctly.
The warming drawer is equipped with a power cable and plug for single phase current. We advise that the plug is connected to a socket that is easily accessible after installation.
If the warming drawer is to be installed on a permanent basis it should be installed by a qualified technician. In such a case, the appliance should be connected to a circuit with an all-pole circuit breaker with a minimum separation of 3 mm between contacts.
To build-in the warming drawer in combination with another appliance there must be a fixed, interim shelf in the housing unit to support the weight of both appliances.
The data necessary for the electrical connection are described on the warming drawer’s characteristics plate and these must be compatible with those of the power outlet you are going to use.
The appliance to be combined with the warming drawer will be placed directly on the latter without any need to have a separating shelf.
To build-in the appliance which is combined with the warming drawer, follow the instructions set out in the respective instructions and fitting booklet.
The manufacturer and retailers do not accept responsibility for any damage that may be caused to people, animals or property if these installation instructions are not observed.
The relevant installation dimensions are indicated in mm in the diagrams shown at the end of this booklet. Proceed as follows:


Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.