Benutzeranleitung / Produktwartung 2010 RDX des Produzenten Acura
Zur Seite of 514
Congratulations! Your selection of a 2010 Acura RDX was a wise investment. It will give you years of driving pleasure. One of the best ways to enhance the enjoyment of your new vehicle is to read this manual. In it, you will learn how to operate its driving controls and convenience items.
California Proposition 65 Warning WARNING: This product contains or emits chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Event Data Recorders This vehicle is equipped with one or more devices commonly referred to as event data recorders.
Your safety, and the safety of others, is very important. And operating this vehicle safely is an important responsibility. To help you make informed decisions about safety, we have provided operating procedures and other information on labels and in this manual.
Your RDX has higher ground clearance than a passenger vehicle designed for use only on pavement. Higher ground clearance has many advantages for off-highway driving. It allows you to travel over bumps, obstacles, and rough terrain. It also provides good visibility so you can anticipate problems earlier.
Your Vehicle at a Glance (main controls) .................................................................................................................... 3 Driver and Passenger Safety (seat belts, SRS, and child protection) .......................
Contents A convenient reference to the sections in this manual. Your Vehicle at a Glance A quick reference to the main controls in your vehicle. Driver and Passenger Safety Important information about.
ꭧ 1: ꭧ 2: ꭧ 3: On models without navigation system. On models with navigation system. HomeLink ® buttons (P. 303 ) Moonroof Switch (P. 144 ) Front Ceiling Light Switch (P. 151 ) INSTRUMENT PANEL INDICATORS (P. 63 ) GAUGES (P. 73 ) DRIVER'S FRONT AIRBAG (P.
ꭧ 1: To use the horn, press the center pad of the steering wheel. ꭧ 2: On models without navigation system. ꭧ 3: Only on vehicles equipped with navigation system. Refer to the navigation system manual. HEADLIGHTS/TURN SIGNAL/FOG LIGHTS (P. 116 / 119 ) REMOTE AUDIO CONTROL BUTTONS (P.
This section gives you important information about how to protect yourself and your passengers. It shows you how to use seat belts properly. It explains how your airbags work, and it tells you how to properly restrain infants and children in your vehicle.
You'll find many safety recommendations throughout this section, and throughout this manual. The recommendations on this page are the ones we consider to be the most important. Always Wear Your Seat Belt A seat belt is your best protection in all types of collisions.
Pay Appropriate Attention to the Task of Driving Safely Engaging in mobile phone conversation or other activities that keep you from paying close attention to the road, other vehicles and pedestrians could lead to a crash. Remember, situations can change quickly, and only you can decide when it is safe to divert attention away from driving.
Your vehicle is equipped with many features that work together to protect you and your passengers during a crash. Some features do not require any action on your part.
Seat Belts Your vehicle is equipped with seat belts in all seating positions. Your seat belt system also includes an indicator on the instrument panel and a beeper to remind you and your passengers to fasten your seat belts. Why Wear Seat Belts Seat belts are the single most effective safety device for adults and larger children.
Airbags Your vehicle has a supplemental restraint system (SRS) with front airbags to help protect the heads and chests of the driver and a front seat passenger during a moderate to severe frontal collision (see page 26 for more information on how your front airbags work).
The most important things you need to know about your airbags are: ● Airbags do not replace seat belts. They are designed to supplement the seat belts. ● Airbags offer no protection in rear impacts, or minor frontal or side collisions. ● Airbags can pose serious hazards .
Introduction The following pages provide instructions on how to properly protect the driver, adult passengers, and teenage children who are large enough and mature enough to drive or ride in the front. See pages 36 － 56 for important guidelines on how to properly protect infants, small children, and larger children who ride in your vehicle.
Locking the doors and the tailgate reduces the chance of someone being thrown out of the vehicle during a crash, and it helps prevent passengers from accidentally opening a door or the tailgate and falling out. Locking the doors and the tailgate also helps prevent an outsider from unexpectedly opening a door or the tailgate when you come to a stop.
Sitting too close to a front airbag can result in serious injury or death if the front airbags inflate. Always sit as far back from the front airbags as possible.
4. Adjust the Head Restraints Adjust the driver's head restraint so the center of the back of your head rests against the center of the restraint. Have passengers adjust their head restraints properly as well. Taller persons should adjust their restraint as high as possible.
Position the lap part of the belt as low as possible across your hips, then pull up on the shoulder part of the belt so the lap part fits snugly. This lets your strong pelvic bones take the force of a crash and reduces the chance of internal injuries.
Never place the shoulder portion of a lap/shoulder belt unde r your arm or behind your back. This could cause very serious injuries in a crash. If a seat belt does not seem to work properly, it may not protect the occupant in a crash. No one should sit in a seat wi th an inoperative seat belt.
Advice for Pregnant Women If you are pregnant, the best way to protect yourself and your unborn child when driving or riding in a vehicle is to always wear a seat belt, and keep the lap part of the belt as low as possible across the hips.
Additional Safety Precautions ● Never let passengers ride in the cargo area or on top of a folded- down back seat. If they do, they could be very seriously injured in a crash. ● Passengers should not stand up or change seats while the vehicle is moving.
Seat Belt System Components Your seat belt system includes lap/ shoulder belts in all seating positions. The front seat belts are also equipped with automatic seat belt tensioners.
If the indicator comes on or the beeper sounds when the driver's seat belt is latched and there is no front seat passenger and no items on the front seat, something may be interfering with the monitoring system. Look for and remove: ● Any items under the front passenger's seat.
If the shoulder part of the belt is pulled all the way out, the lockable retractor will activate. The belt will retract, but it will not allow the passenger to move freely. To deactivate the lockable retractor, unlatch the buckle and let the seat belt fully retract.
Seat Belt Maintenance For safety, you should check the condition of your seat belts regularly. Pull each belt out fully, and look for frays, cuts, burns, and wear. Check that the latches work smoothly and the belts retract easily. If a belt does not retract easily, cleaning the belt may correct the problem (see page 438 ).
Airbag System Components (9) (14) (10) (9) (2) (13) (12) (6) (5) (15) (11) (4) (16) (8) (17) (16) (5) (4) (1) Driver's Front Airbag (2) Passenger's Front Airbag (3) Control Unit (4) Front Se.
Your airbag system includes: ● Two SRS (supplemental restraint system) front airbags. The driver's airbag is stored in the center of the steering wheel; the front passenger's airbag is stored in the dashboard. Both are marked ‘‘ SRS AIRBAG ’’ (see page 26 ).
● An indicator on the instrument panel that alerts you to a possible problem with your airbags, sensors, or seat belt tensioners (see page 32 ). ● An indicator on the instrument panel that alerts you that the passenger's side airbag has been turned off (see page 32 ).
After inflating, the front airbags immediately deflate, so they won't interfere with the driver's visibility, or the ability to steer or operate other controls. The total time for inflation and deflation is one-tenth of a second, so fast that most occupants are not aware that the airbags deployed until they see them lying in their laps.
Dual-Threshold Airbags Your front airbags are also dual- threshold airbags. Airbags with this feature have two deployment thresholds that depend on whether sensors detect the occupant is wearing a seat belt or not.
The passenger's advanced front airbag system has weight sensors under the seat. Although Acura does not encourage carrying an infant or small child in front, if the sensors detect the weight of an infant or small child (up to about 65 lbs or 29 kg), the system will automatically turn the passenger's front airbag off.
How Your Side Airbags Work If you ever have a moderate to severe side impact, sensors will detect rapid acceleration and signal the control unit to instantly inflate either the driver's or the passenger's side airbag. Only one airbag will deploy during a side impact.
If the side airbag off indicator comes on (see page 32 ), have the passenger sit upright. Once the passenger is out of the airbag's deployment path, the system will turn the airbag back on, and the indicator will go out.
How the SRS Indicator Works The SRS indicator alerts you to a potential problem with your airbags or seat belt tensioners. When you turn the ignition switch to the ON (II) position, this indicator comes on for several seconds then goes off. This tells you the system is working properly.
How the Passenger Airbag Off Indicator Works This indicator alerts you that the passenger's front airbag has been shut off because weight sensors detect about 65 lbs (29 kg) or less (the weight of an infant or small child) on the front passenger's seat.
Airbag Service Your airbag systems are virtually maintenance free, and there are no parts you can safely service. However, you must have your vehicle serviced if: ● An airbag ever inflates. Any airbag that has deployed must be replaced along with the control unit and other related parts.
Additional Safety Precautions ● Do not attempt to deactivate your airbags. Together, airbags and seat belts provide the best protection. ● Do not tamper with airba g components or wirin g for any reason. Tampering could cause the airbags to deploy, possibly causing very serious injury.
Children depend on adults to protect them. However, despite their best intentions, many adults do not know how to properly protect child passengers. If you have children, or ever need to drive with a child in your vehicle, be sure to read this section.
All Children Should Sit in a Back Seat According to accident statistics, children of all ages and sizes are safer when they are restrained in a back seat. The National Highway Traffic Safety Administration and Transport Canada recommend that all children aged 12 and under be properly restrained in a back seat.
To remind you of the passenger's front airbag hazards, and that children must be properly restrained in a back seat, your vehicle has warning labels on the dashboard (U.S. models) and on the front visors. Please read and follow the instructions on these labels.
If You Must Drive with Several Children Your vehicle has a back seat where children can be properly restrained. If you ever have to carry a group of children, and a child must ride in front: ● Place the largest child in the front seat, provided the child is large enough to wear the lap/shoulder belt properly (see page 53 ).
Additional Safety Precautions ● Never hold an infant or child on your lap. If you are not wearing a seat belt in a crash, you could be thrown forward and crush the child against the dashboard or a seat-back. If you are wearing a seat belt, the child can be torn from your arms and be seriously hurt or killed.
Protecting Infants Child Seat Type An infant must be properly restrained in a rear-facing, reclining child seat until the child reaches the seat maker's weight or height limit for the seat, and the child is at least one year old. Only a rear-facing child seat provides proper support for a baby's head, neck, and back.
In any of these situations, we strongly recommend that you install the child seat directly behind the front passenger's seat, move the seat as far forward as needed, and leave it unoccupied. Or, you may wish to get a smaller rear-facing child seat.
Child Seat Placement We strongly recommend placing a forward-facing child seat in a back seat, not the front. Placing a forward-facing child seat in the front seat of a vehicle equi pped with a passenger's airbag can be hazardous.
When buying a child seat, you need to choose either a conventional child seat, or one designed for use with the Lower Anchors and Tethers for CHildren (LATCH) system.
After selecting a proper child seat and a good place to install the seat, there are three main steps in installing the seat: 1. Properly secure the child seat to the vehicle. All child seats must be secured to the vehicle with the lap part of a lap/shoulder belt or with the LATCH (Lower Anchors and Tethers for CHildren) system.
Installing a Child Seat with LATCH Your vehicle is equipped with LATCH (Lower Anchors and Tethers for CHildren) at the rear seats to secure a child seat in any seating position: one in each outer seating position, or one in the center.
3. Place the child seat on the vehicle seat, then attach the seat to the lower anchors according to the child seat maker's instructions. Some LATCH-compatible seats have a rigid-type connector as shown above. Other LATCH-compatible seats have a flexible-type connector as shown above.
7. Attach the tether strap hook to the tether anchor, then tighten the strap as instructed by the child seat maker. 8. Push and pull the child seat forward and from side-to-side to verify that it is secure.
If you want to install two child seats in the back seats, place each child seat in the outer seat, as shown in the above illustration. Do not attach two child seat connectors to a single lower anchor at a time. The LATCH system or the child seats might be damaged if you try to install three child seats in the rear seats.
Installing a Child Seat with a Lap/ Shoulder Belt When not using the LATCH system, all child seats must be secured to the vehicle with the lap part of a lap/ shoulder belt. In addition, the lap/shoulder belts in all seating positions except the driver's have a lockable retractor that must be activated to secure a child seat.
4. After confirming that the belt is locked, grab the shoulder part of the belt near the buckle, and pull up to remove any slack from the lap part of the belt.
1. Remove the cargo area cover, and place it on the cargo area floor (see page 160 ). 2. (Outer seating position) After properly securing the child seat (see page 50 ), lift the head restraint, then route the tether strap over the seat-back and through the head restraint legs.
When a child reaches the recommended weight or height limit for a forward-facing child seat, the child should sit in a back seat on a booster seat and wear a lap/shoulder belt.
3. Does the shoulder belt cross between the child's neck and arm? 4. Is the lap part of the belt as low as possible, touching the child's thighs? 5. Will the child be able to stay seated like this for the whole trip? If you answer yes to all these questions, the child is ready to wear the lap/shoulder belt correctly.
If a child who uses a booster seat must ride in front, move the vehicle seat as far back as possible and be sure the child is wearing the seat belt properly. A child may continue using a booster seat until the tops of their ears are even with the top of the vehicle's or booster's seat-back.
If you decide that a child can safely ride up front, be sure to: ● Carefully read the owner's manual, and make sure you understand all seat belt instructions and all safety information. ● Move the vehicle seat to the rear- most position. ● Have the child sit up straight, back against the seat, and feet on or near the floor.
Your vehicle's exhaust contains carbon monoxide gas. Carbon monoxide should not enter the vehicle in normal driving if you maintain your vehicle properly and follow the information on this page. Have the exhaust system inspected for leaks whenever: ● The vehicle is raised for an oil change.
DASHBOARD U.S. models only SUN VISORS U.S. models Canadian models SUN VISOR U.S. models only These labels are in the locations shown. They warn you of potential hazards that could cause serious injury or death. Read these labels carefully. If a label comes off or becomes hard to read (except for the U.
DOOR JAMBS U.S. models RADIATOR CAP Canadian models Safety Labels 59 Driver and Passenger Safety 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
60 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
This section gives information about the controls and displays that contribute to the daily operation of your vehicle. All the essential controls are within easy reach. Control Locations .......................... 62 Instrument Panel .................
ꭧ 1: On models without navigation system. ꭧ 2: On models with navigation system. ꭧ 3: HomeLink ® Buttons (P. 303 ) Moonroof Switch (P. 144 ) Front Ceiling Light Switch (P. 151 ) INSTRUMENT PANEL INDICATORS (P. 63 ) GAUGES (P. 73 ) DRIVING POSITION MEMORY SYSTEM (P.
The U.S. instrument panel is shown. Differences for the Canadian models are noted in the text. VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR (P. 68 ) HIGH BEAM INDICATOR (P. 69 ) LOW TIRE PRESSURE/TPMS INDICATOR (P. 71 , 390 ) VEHICLE STABILITY ASSIST (VSA) ACTIVATION INDICATO R (P.
The instrument panel has many indicators that give you important information about your vehicle. Seat Belt Reminder Indicator This indicator reminds you and your passengers to fasten your seat belts. If you turn the ignition switch to the ON (II) position before fastening your seat belts, the beeper sounds, and the indicator flashes.
Malfunction Indicator Lamp You will also see a ‘‘ CHECK EMISSION SYSTEM ’’ message on the multi-information display. For more information, see page 466 . Low Oil Pressure Indicator The engine can be severely damaged if this indicator flashes or stays on when the engine is running.
U.S. Canada Side Airbag Off Indicator This indicator comes on when you turn the ignition switch to the ON (II) position. If it comes on at any other time, it indicates that the passenger's side airbag has automatically shut off.
U.S. Canada Parking Brake and Brake System Indicator (Red) This indicator has two functions: 1. It comes on when you turn the ignition switch to the ON (II) position. It is a reminder to check the parking brake. Driving with the parking brake not fully released can damage the brakes and tires.
Low Fuel Indicator This indicator comes on as a reminder that you must refuel soon. When the indicator comes on, there are about 2.5 U.S. gal (9.5 L) of fuel remaining in the tank. When the needle reaches E, there is a very small amount of fuel in the tank.
VSA Activation Indicator This indicator has three functions: 1. It comes on as a reminder that you have turned off the vehicle stability assist (VSA) system. 2. It flashes when VSA is active (see page 395 ). 3. It comes on along with the VSA system indicator if there is a problem with the VSA system.
Security System Indicator This indicator comes on when the security system is set. For more information, see page 294 . Lights On Indicator This indicator reminds you that the exterior lights are on. It comes on when the light switch is in either the or position.
If this indicator blinks while driving, it indicates the differential temperature is too high. You will also see an ‘‘ SH-AWD DIFF TEMP. HIGH ’’ message on the multi- information display (see page 80 ). Pull to the side of the road when it is safe, shift to Park, and let the engine idle until the indicator goes out.
2. If this indicator begins to flash, there is a problem with the tire pressure monitoring system (TPMS). You will also see a ‘‘ CHECK TPMS SYSTEM ’’ message on the multi-information display. The indicator continues to flash for a while (approximately 1 minute), then stays on.
Turbo Boost Meter When the turbo charger is activated, this meter shows the boost pressure. Fuel Gauge This shows how much fuel you have. It may show slightly more or less than the actual amount. The needle returns to the bottom after you turn off the ignition.
The multi-information display in the instrument panel displays various information and messages when the ignition switch is in the ON (II) position. Some of the messages help you operate your vehicle more comfortably. Others help to keep you aware of the periodic maintenance your vehicle needs for continued trouble-free driving.
U.S. model is shown. IGNITION ON Press the SEL/ RESET Button Press the INFO ( ▲ / ▼ ) Button IGNITION OFF (SH-AWD model only) CONTINUED Multi-Information Display 75 Instruments and Controls 09/07/.
Odometer The odometer shows the total distance your vehicle has been driven. It measures miles in U.S. models and kilometers in Canadian models. It is illegal under U.S. federal law and Canadian provincial/ territorial regulations to disconnect, reset, or alter the odometer with the intent to change the number of miles or kilometers indicated.
Maintenance Minder The multi-information display in the instrument panel shows you the engine oil life and maintenance service items when the ignition switch is in the ON (II) position. This information helps to keep you aware of the periodic maintenance your vehicle needs for continued trouble- free driving.
SH-AWD Torque Distribution Monitor On SH-AWD models This monitor shows how much torque is being delivered to each wheel. For more information, see page 384 . Tire Pressure Monitor You can see the pressure of each tire in this monitor. If one or more tire pressure are low, inflate them to the correct pressure.
System Messages If there is a problem with your vehicle, for example, the engine oil level is low or a door is not fully closed, the multi-information display will show you the problem. It does this by interrupting the current display with one or more messages.
See page 376 See page 385 See page 385 See page 32 See page 388 See page 395 See page 375 See page 32 See page 119 See page 68 See page 12 See page 354 See page 426 See page 412 See page 125 SH-AWD model only SH-AWD model only U.
The system message(s) triggers the appropriate indicator(s) on the instrument panel, including the system message indicator, to come on. The system message indicator does not go off until the problem(s) is corrected. You will also hear a beep when the system message comes on for the first time.
Customized Settings With the multi-information display and the INFO ( / ) and SEL/ RESET buttons on the right side of the steering wheel, you can customize some vehicle control settings. To enter the customizing mode, press and hold the INFO ( / ) button for more than 3 seconds.
Customize Entry Customize Group Customize Menu Description Customize Setup Page CHG SETTING (P. 86 ) METER SETUP (P. 88 ) LANGUAGE SELECTION Changes the language used in the display. ENGLISH ꭧ 89 FRENCH SPANISH ADJUST OUTSIDE TEMP. DISPLAY Changes the outside temperature reading above or below its current reading.
Customize Entry Customize Group Customize Menu Description Customize Setup Page CHG SETTING (P. 86 ) DOOR SETUP (P. 102 ) DOOR LOCK MODE Changes which doors unlock with the remote transmitter on a first push. DRIVER DOOR ꭧ 105 ALL DOORS KEYLESS LOCK ACKNOWLEDGEMENT The exterior lights flash each time you press the LOCK or UNLOCK button.
DEFAULT ALL To enter the customizing mode, press and hold the INFO ( / ) button for more than 3 seconds. If you want to set the default settings, press the INFO ( / ) button to select DEFAULT ALL, then press the SEL/RESET button. To set the default settings, press the INFO ( / ) button to select SET then press the SEL/RESET button.
If DEFAULT ALL is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE ENTRY. Repeat the procedure to select DEFAULT ALL. If you want to cancel DEFAULT ALL, select EXIT, then press the SEL/ RESET button. The screen goes back to CUSTOMIZE ENTRY.
: Press and hold the : Press the SEL/RESET : Press the INFO ( ▲ / ▼ ) See page 88 See page 97 See page 102 INFO ( ▲ / ▼ ) button (3 seconds) button or the select/ reset knob button or rotate t.
Meter Setup Here are the four custom settings for the meter setup: ● LANGUAGE SELECTION ● ADJUST OUTSIDE TEMP. DISPLAY ● TRIP A & AVG. FUEL RESET with REFUEL ● ELAP. TIME RESET CONDITION While METER SETUP is shown in the CUSTOMIZE GROUP of the multi-information display, press the SEL/RESET button.
Language Selection There are three language selections you can make: English, French, and Spanish. To choose the language you want, follow these instructions: While METER SETUP is shown in the CUSTOMIZE GROUP of the multi-information display, press the SEL/RESET button.
When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. All messages on the multi- information display will be shown in the language you selected. If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU.
Adjust Outside Temp. Display If you sometimes find that the temperature reading is a few degrees above or below the actual temperature, you can adjust it by following these instructions: While METER SETUP is shown in the CUSTOMIZE GROUP of the multi-information display, press the SEL/RESET button.
When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.
Trip A & Avg. Fuel Reset with Refuel To cause Trip A and AVG. FUEL A to reset every time you refuel your vehicle, follow these instructions: While METER SETUP is shown in the CUSTOMIZE GROUP of the multi-information display, press the SEL/RESET button.
When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.
Elap. Time Reset Condition There are three elapsed time reset choices you can make: IGN RESET － The elapsed time is reset when you turn the ignition switch to the LOCK (0) position. TRIP A － The elapsed time is reset when Trip A is reset. TRIP B － The elapsed time is reset when Trip B is reset.
When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.
Lighting Setup There are two settings in the lighting setup: ● INTERIOR LIGHT DIMMING TIME ● HEADLIGHT AUTO OFF TIMER While CUSTOMIZE GROUP is shown on the multi-information display, select LIGHTING SETUP by pressing the INFO ( / ) button, then press the SEL/RESET button.
Interior Light Dimm ing Time The interior lights fade out when you close all doors. You can change the time that the interior lights fade out. While LIGHTING SETUP is shown in the CUSTOMIZE GROUP of the multi-information display, press the SEL/RESET button.
When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.
Headlight Auto Off Timer The headlights, parking lights, side marker lights, taillights, and license plate lights go off after the selected time when you close the driver's door and take the remote with you.
When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.
Door Setup Here are the five custom settings for the door setup: ● AUTO DOOR LOCK ● DOOR LOCK MODE ● KEYLESS LOCK ACKNOWLEDGEMENT ● SECURITY RELOCK TIMER ● AUTO DOOR UNLOCK While CUSTOMIZE GROUP is shown on the multi-information display, select DOOR SETUP by pressing INFO ( / ) button, then press the SEL/RESET button.
Auto Door Lock There are three settings you can choose from: OFF － The auto door lock is deactivated all the time. WITH VEH SPD － The doors lock when the vehicle speed reaches about 9 mph (about 15 km/h). SHIFT FROM P － The doors lock whenever you move the shift lever out of Park.
When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.
Door Lock Mode To select whether the driver's door unlocks or all the doors unlock when you unlock the doors with the remote transmitter or the key, follow these instructions. While DOOR SETUP is shown in the CUSTOMIZE GROUP of the multi- information display, press the SEL/ RESET button.
When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.
Keyless Lock Acknowledge ment When you press the UNLOCK button on the remote transmitter to unlock the doors and the tailgate, the exterior lights blink twice to verify that the doors and the tailgate are unlocked and the security system is turned off.
When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.
Security Relock Timer If you unlock the doors and the tailgate with the remote transmitter, but do not open any of the doors or the tailgate within 30 seconds, the doors and the tailgate automatically relock and the security system sets. You can change this relock time from 30 seconds to 60 or 90 seconds.
When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.
Auto Door Unlock There are three settings you can choose from: SHIFT TO P － The driver's door or all the doors unlock when you move the shift lever to Park. IGN OFF － The driver's door or all the doors unlock when you turn the ignition switch to the LOCK (0) position.
When your choice is set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If your choice is not set, you will see the above display for several seconds, then the screen goes back to CUSTOMIZE MENU. If this happens, you need to repeat the same procedure.
ꭧ 1: To use the horn, press the center pad of the steering wheel. ꭧ 2: On models without navigation system. ꭧ 3: Only on vehicles equipped with navigation system. Refer to the navigation system manual. BLUETOOTH HANDSFREELINK BUTTONS (P. 306 ) HORN ꭧ 1 STEERING WHEEL ADJUSTMENTS (P.
Windshield Wiper 1. MIST 2. OFF 3. INT － Intermittent 4. LO － Low speed 5. HI － High speed 6. Windshield washers Push the right lever up or down to select a position. MIST － The wipers run at high speed until you release the lever. OFF － The wipers are not activated.
Rear Window Wiper and Washer 1. ON 2. OFF 3. Rear Window Washer with Wiper 4. Rear Window Washer Only. ON － Rotate the switch clockwise to turn the rear window wiper ON.
1. Turn signal 2. Off 3. Parking and interior lights 4. AUTO 5. Headlights on 6. High beams 7. Flash high beams 8. Fog lights off 9. Fog lights on Turn Signal － Push down on the lever to signal a left turn and up to signal a right turn. To signal a lane change, push lightly on the lever, and hold it.
High Beams － Push the lever forward and the high beam indicator will come on (see page 69 ). Pull it back to return to low beams. To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.
Even with the automatic lighting feature turned on, we recommend that you turn on the lights manually when driving at night or in a dense fog, or when you enter dark areas such as long tunnels or parking facilities. Do not leave the light switch in AUTO if you will not be driving the vehicle for an extended period (a week or more).
If you remove the key from the ignition switch with the headlight switch on, but do not open the door, the lights will turn off after 10 minutes. The lights will turn on again when you unlock or open the driver ’ s door. If you unlock the door, but do not open it within 15 seconds, the lights will go off.
The knob on the instrument panel controls the brightness of the instrument panel lights. Turn the knob to adjust the brightness. Separate adjustments can be made when the headlights are on and off. You will hear a beep when maximum or minimum brightness is reached.
Rear Window Defogger The rear window defogger clears fog, frost, and thin ice from the window. Push the defogger button to turn it on and off. The indicator in the button comes on to show the defogger is on. If you do not turn it off, the defogger will shut itself off within about 5 to 30 minutes according to the outside temperature.
Steering Wheel Adjustments Make any steering wheel adjustments before you start driving. Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash. Adjust the steering wheel only when the vehicle is stopped.
You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Acura-approved key blanks. These keys contain electronic circuits that are activated by the immobilizer system.
The immobilizer system protects your vehicle from theft. If an improperly coded key (or other device) is used, the engine's fuel system is disabled. When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off.
The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III). LOCK (0) － You can insert or remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly. If the front wheels are turned, the anti-theft lock may make it difficult to turn the key.
Power Door Locks Each front door has a master door lock switch. Either switch locks and unlocks all doors and the tailgate. Push the top of the switch to lock all doors and the tailgate; push the bottom to unlock them. Each door has a lock tab next to the inside door handle.
When the vehicle speed reaches about 9 mph (about 15 km/h) or more, all the doors lock automatically. You can change the ‘‘ AUTO DOOR LOCK ’’ setting on the multi- information display (see page 103 ). When you shift to P after driving, the driver's door unlocks.
The tailgate will lock when you lock the driver's door, and will unlock when you unlock all doors. You can change the ‘‘ DOOR LOCK MODE ’’ setting on the multi- information display (see page 105 ). To open the tailgate, press and hold the switch, then lift up.
Unlocking the Tailgate If the power door lock system cannot unlock the tailgate, unlock it manually. Place a cloth on the top side of the cover to prevent scratches, then use a small flat-tip screwdriver to remove the cover on the back of the tailgate.
LOCK － Press this button once to lock all doors and the tailgate. Some exterior lights will flash. When you push LOCK twice within 5 seconds, you will hear a beep to verify that the doors and tailgate are locked and the security system has set. This button does not work if any door or tailgate is not fully closed.
Remote Transmitter Care ● Avoid dropping or throwing the transmitter. ● Protect the transmitter from extreme temperature. ● Do not immerse the transmitter in any liquid. ● If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
3. Place a cloth on the edge of the keypad to prevent scratches, and remove the upper half by carefully prying on the edge with a small flat-tip screwdriver. 4. Remove the old battery and note the polarity. Make sure the polarity of the new battery is the same ( － side facing up), then insert it in the keypad.
Keyless Memory Settings ™ When you unlock the driver's door with your remote, each remote activates the keyless memory settings related to that remote. The driver's ID (MEMORY 1 or MEMORY 2) is shown on the back of each remote. Here are the settings activated with the remote; ● Driving position memory (see page 148 ).
Front Seat Power Adjustments See pages 13 － 14 for important safety information and warnings about how to properly position the seats and seat- backs. The controls for the power adjustable front seats are on the outside edge of each seat bottom. You can adjust the seats with the ignition switch in any position.
Head Restraints See page 15 for important safety information and a warning about improperly position ing head restraints. Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from whiplash and other injuries.
Removing the Head Re straint To remove a head restraint for cleaning or repair, pull it up as far as it will go. Push the release button, then pull the restraint out of the seat- back. When reinstalling a head restraint, put the legs back in place. Then adjust it to the appropriate height while pressing the release button.
Active Head Restraints The driver's and front passenger's seats have active head restraints. If the vehicle is struck severely from the rear, the occupant properly secured with the seat belt will be pushed against the seat-back and the head restraint will automatically move forward.
Armrests The lid of the console compartment can be used as an armrest. The rear seat armrest is in the center of the rear seat. Pivot it down to use it. A beverage holder is located in the armrest. Folding the Rear Seats Down The rear seat-backs can be folded down to give more cargo room.
1. Move the front seats as far forward as possible. Make sure the front seat-backs are in the upright positions. 2. Store the center seat belt buckle into the pocket in the rear seat- back. 3. Lower the head restraints to their lowest positions. 4. Push the armrest back in place.
Do not put any heavy items on the seat-back when it is folded down. Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have to brake hard (See Carrying Cargo on page 364 ). Make sure that the folded down rear seat does not interfere with the front passenger's seat-back.
Both front seats are equipped with seat heaters. The passenger seat is only heated in the seat bottom because of the side airbag cutoff system. The ignition switch must be in the ON (II) position to use seat heaters. Push the top of the switch, HI, to rapidly heat up the seat.
Turn the ignition switch to the ON (II) position to raise or lower any window. To open the window, push the switch down and hold it. Release the switch when you want to stop the window. To close the window, pull back on the switch and hold it. The windows will operate for up to 10 minutes after you turn off the ignition switch.
AUTO － To open or close either front window fully, push or pull the window switch firmly down or up to the second detent, and release it. The window will automatically go up or down all the way. To stop the window, pull or push the window switch briefly.
Turn the ignition switch to the ON (II) position before operating the moonroof switch on the ceiling console. To open the moonroof fully, pull back the moonroof switch firmly. The moonroof opens all the way. To stop the moonroof from opening fully, briefly move the switch in either direction.
Opening or closing the moonroof on someone's hands or fingers can cause serious injury. Make sure all hands and fingers are clear of the moonroof before opening or closing it. The moonroof has a key-off delay. You can open and close the moonroof for up to 10 minutes after you turn off the ignition switch.
Keep the inside and outside mirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving. The inside mirror can automatically darken to reduce glare. To turn on this feature, press the button on the bottom of the mirror.
3. Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down. 4. When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your setting. Outside mirror positions can be stored in the driving position memory system (see page 148 ).
Your vehicle has a memory feature for the driver's seat and outside mirror positions. Seat, except for power lumbar, and outside mirror positions, can be stored in separate memories. You select a memorized position by pushing the appropriate button or using the appropriate remote transmitter (Memory 1 or Memory 2).
To cancel the storing procedure after pressing the SET button, do any of the following: ● Fail to press a memory button within 5 seconds. ● Readjust the seat position. ● Readjust the outside mirror position. Each memory button stores only one driving position.
To apply the parking brake, push the pedal down with your foot. To release it, push on the pedal again. The parking brake indicator on the instrument panel should go out when the parking brake is fully released (see page 67 ). Driving the vehicle with the parking brake applied can damage the rear brakes and axles.
Ceiling Lights Each front and rear ceiling light has a three-position switch. Front ceiling lights: In the ‘‘ ’’ position, both front and rear ceiling lights are on all the time except when the rear ceiling light switch is in the OFF position.
In the door activated position, both front and rear ceiling lights come on when you: ● Open any door. ● Remove the key from the ignition switch. ● Unlock the doors with the key, lock tab on the driver's door, master door lock switch, or remote transmitter.
Courtesy Lights The courtesy lights in the ceiling console come on when the parking lights are turned on. You can adjust their brightness by turning the select/reset knob on the instrument panel. In addition to the courtesy lights on the ceiling, the driver's and front passenger's ambient foot lights come on.
CARGO AREA COVER BEVERAGE HOLDERS in REAR SEAT ARMREST CENTER CONSOLE ACCESSORY POWER SOCKETS GLOVE BOX CENTER POCKET SUN VISOR/VANITY MIRROR BEVERAGE HOLDERS FRONT DOOR POCKET DOOR LINING POCKETS COA.
Glove Box Open the glove box by pulling the handle to the left. Close it with a firm push. Lock or unlock the glove box with the master key. An open glove box can cause serious injury to your passenger in a crash, even if the passenger is wearing the seat belt.
Beverage Holders Be careful when you are using the beverage holders. A spilled liquid that is very hot can scald you or your passengers. Spilled liquids can damage the upholstery, carpeting, and electrical components in the interior. To use the front beverage holder, push on the lid.
Accessory Power Sockets To use the accessory power socket, pull up the cover. The ignition switch must be in the ACCESSORY (I) or ON (II) position. These sockets are intended to supply power for 12 volt DC accessories that are rated 120 watts or less (10 amps).
Vanity Mirror To use the vanity mirror on the back of the sun visor, pull up the cover. The light comes on when you pull up the cover. Console Compartment Your vehicle has a multi-function console compartment. It includes an armrest, a coin holder, a pen holder, a card holder, a removable tray, and a console compartment with two separable shelves.
You can use the inside of the lid for a pen holder, a coin holder and a card holder. The console compartment light comes on when the parking lights are on. You can store small items on the removable tray. To remove the tray, pull it out from the console compartment frame to get more space.
When you store a large item like a briefcase, lift the shelves up to create a large space. The maximum dimensions of the item you can store in the console compartment are: Length: 16.
3. Place the cargo area cover on the cargo area floor. Make sure the cargo area cover is securely placed so it will not move while you are driving. Reverse this procedure to install the cargo area cover.
162 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
The climate control system in your vehicle provides a comfortable driving environment in all weather conditions. The standard audio system has many features. This section describes those features and how to use them. Your vehicle has an anti-theft audio system that requires a code number to enable it.
OFF BUTTON DUAL BUTTON FAN CONTROL BUTTONS Models without navigati on system AUTO BUTTON DRIVER'S SIDE TEMPERATURE DISPLAY RECIRCULATION BUTTON DRIVER'S SIDE TEMPERATURE CONTROL BUTTONS U.
Proper use of the climate control system can make the interior dry and comfortable, and keep the windows clear for best visibility. For the climate control system to provide heating and cooling, the engine must be running. You can adjust the temperatures of the driver's side and the passenger's side independently (see page 169 ).
When you set the temperature to its lowest limit ( ) or its highest limit ( ), the system runs at full cooling or heating only. It does not regulate the interior temperature. In cold weather, the fan will not come on automatically until the heater starts to develop warm air.
Recirculation Button When the indicator in the button is on, air from the vehicle's interior is sent through the system again. When the indicator is off, air is brought in from the outside of the vehicle (fresh air mode). The outside air intakes for the climate control system are at the base of the windshield.
Mode Button Use the MODE button to select the vents the air flows from. Some air will flow from the dashboard corner vents in all modes. The mode indicator in the display changes to the current mode each time you press the button. Air flows from the center and corner vents in the dashboard.
Dual Temperature Control Your vehicle has four temperature control buttons, two for the driver, and two for the front passenger. The driver's side and the passenger's side can be controlled independently by adjusting these buttons when the indicator in the DUAL button is lit.
When you set the temperature to its lower or upper limit, it is displayed as or . Push AUTO or . The selected temperatures appear in the display. When the indicator in the DUAL button is off, you can adjust both sides to the same temperature by adjusting the driver's side temperature control buttons ( or ).
Climate Control Sensors The climate control system has two sensors. A sunlight sensor is in the top of the dashboard, and a temperature sensor is next to the steering column.
Read the appropriate pages in this section for operation of the audio systems installed in your vehicle. ● For vehicles without navigation system, see pages 174 thru 215 . ● For vehicles with navigation system, see page 216 thru 286 . Models without navigation system U.
Models with navigation system U.S. model is shown. Audio System 173 Features 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
To Play the Radio The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Turn the system on by pushing the PWR/VOL knob, or the AM or FM button. Adjust the volume by turning the PWR/VOL knob. The band and frequency that the radio was last tuned to is displayed.
To Select a Station You can use any of five methods to find radio stations on the selected band: tune, seek, scan, the preset bars, and auto select. TUNE － Use the TUNE/FOLDER bar to tune the radio to a desired frequency. Press the side of the bar to tune to a higher frequency, and the side of the bar to tune to a lower frequency.
AUTO SELECT － If you are traveling and can no longer receive your preset stations, you can use the auto select feature to find stations in the local area. To activate it, press the A.SEL/RDM button. ‘‘ A.SEL ’’ will flash on the center display, and the system will go into scan mode for several seconds.
Adjusting the Sound Press the SOUND/CLOCK button repeatedly to display the BASS, TREBLE, FADER, BALANCE, SUBWOOFER and SVC (speed- sensitive volume compensation) settings. Each mode is shown on the center display as it changes. Turn the PWR/ VOL knob to adjust the setting to your liking.
SUBWOOFER － Use the SUBWOOFER mode to adjust the strength of the sound from the subwoofer speaker. Turn the PWR/ VOL knob to the desired level ( － 6t o ＋ 6). Even if the adjustment level reaches － 6, the subwoofer is not turned off. Speed-sensitive volume compensation (SVC) － The SVC mode controls the volume based on vehicle speed.
Your vehicle is capable of receiving XM ® Radio anywhere in the United States and Canada, except Hawaii, Alaska, and Puerto Rico. XM is a registered trademark of Sirius XM Radio Inc. and XM CANADA ® is a registered business name of Canadian Satellite Radio Inc.
Operating the XM Radio To listen to the XM Radio, turn the ignition switch to the ACCESSORY (I) or ON (II) position. Push the PWR/VOL knob to turn on the audio system, and press the button. Adjust the volume by turning the PWR/VOL knob. The last channel you listened to will show on the audio display.
SCAN － The scan function gives you a sampling of all channels while in the channel mode. In the category mode, only the channels within that category are scanned. To activate scan, press the SCAN button. The system plays each channel in numerical order for a few seconds, then selects the next channel.
XM Radio Display Messages ‘‘ LOADING ’’ ꭚ XM is loading the audio or program information. ‘‘ OFF AIR ’’ ꭚ The channel currently selected is no longer broadcasting. ‘‘ UPDATING ’’ ꭚ The encryption code is being updated. Wait until the encryption code is fully updated.
Satellite Radio Signals Satellite radio receives signals from two satellites to produce clear, high- quality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, satellite radio also allows you to view channel and category selections in the audio display.
Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions: ● Driving on the north side of an east/west mountain road. ● Driving on the north side of a large commercial truck on an east/west road.
Normal mode MP3/WMA mode SCAN (D-SCAN) INDICATOR RPT (D-RPT) INDICATOR FOLDER NUMBER SCAN (F-SCAN) INDICATOR RPT (F-RPT) INDICATOR DISC NUMBER TRACK NUMBER DISC INDICATOR RDM (F-RDM) INDICATOR MP3 MODE INDICATOR WMA MODE INDICATOR U.S. model is shown.
U.S. model is shown . CD/AUX BUTTON RPT BUTTON SCAN BUTTON SEEK/SKIP BAR LOAD BUTTON DISC SLOT DISP/MODE BUTTON A.SEL/RDM BUTTON TUNE/FOLDER BAR PWR/VOL KNOB PRESET BARS EJECT BUTTON DISC LOAD INDICAT.
Your audio system has an in-dash CD changer that holds up to six CDs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the radio. To load CDs or operate the CD changer, the ignition switch must be in the ACCESSORY (I) or ON (II) position.
Loading CDs in the Changer To load multiple discs in one operation: 1. Press and hold the LOAD button on the changer unit until you hear a beep. You will see ‘‘ BUSY ’’ on the center display, and disc load indicator turns red and starts blinking.
3. You will see ‘‘ DISC READ ’’ on the center display, then the system begins to play the CD. You can load a CD into an empty position while a CD is playing. Select the empty position (the disc indicator is not shown on the center display) by pressing the appropriate side of the preset bars.
The specifications for compatible MP3 files are: – Sampling frequency: 32/44.1/48 kHz (MPEG1) 24/22.05/16 kHz (MPEG2) – Bitrate: 32/40/48/56/64/80/96/112/128/ 160/192/224/256/320 kbps (MPEG1) 8/16.
To Change or Select Tracks/Files While a disc is playing you can use the SEEK/SKIP bar to select passages and change tracks (files in MP3/WMA mode). In MP3/WMA mode, use the TUNE/FOLDER bar to select folders on the disc, and use the SEEK/SKIP bar to change files.
In MP3/WMA mode FOLDER REPEAT － This feature, when activated, replays all the files in the current folder in the order they are compressed in MP3/WMA. To activate folder repeat mode, press the RPT button twice. You will see ‘‘ F- RPT ’’ on the center display.
DISC SCAN － The disc scan function samples the first track (file in MP3/WMA mode) on each disc within the changer in numerical order. To activate this feature, press the SCAN button twice. In MP3/ WMA mode, press the SCAN button three times. The first track/file on each disc plays for about 10 seconds.
To Pause a Disc To pause a disc, press the corresponding number of the current disc on the appropriate side of the preset bars. To play the disc again, press the preset bar again.
If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take the vehicle to your dealer. Error Message Cause Solution FOCUS Error Press the EJECT button, and pull out the disc.
The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again.
iPod INDICATOR RPT BUTTON SEEK/SKIP BAR PWR/VOL KONB RDM BUTTON CD/AUX BUTTON USB INDICATOR DISP BUTTON SOUND/CLOCK BUTTON TUNE/FOLDER BAR U.S. model is shown.
To Play an iPod ® This audio system can operate the audio files on the iPod ® with the same controls used for the disc player. To play an iPod, connect it to the USB adapter cable in the console compartment by using your dock connector, then press the CD/AUX button.
Connecting an iPod 1. Push the release button to release the USB adapter cable. 2. Connect your dock connector to the iPod correctly and securely. 3. Install the dock connector to the USB adapter cable securely. If the iPod indicator does not appear in the center display, check the connections, and try to reconnect the iPod a few times.
Text Data Display Function Each time you press the DISP/ MODE button, the display mode switches between the album name, the song name, the artist name, or name off (which turns off the text display). The center display shows up to about 16 characters of the selected data.
The center display shows items on the selected list. Press either side of the TUNE/FOLDER bar repeatedly. After making a selection, wait for a few seconds to set your selection. If you select ‘‘ ALL, ’’ all available files on the selected list are played.
To Stop Playing Your iPod To play the radio, press the AM/FM, or button. Press the CD/AUX button to switch between disc (if a disc is loaded), Bluetooth ® Audio, and the iPod. Disconnecting an iPod You can disconnect the iPod at any time when you see the ‘‘ OK to disconnect ’’ message ꭧ in the iPod display.
If you see an error message in the center display while playing an iPod, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. Error Message Cause Solution USB ERROR USB ROM error There is a problem with the USB adapter unit.
FILE TYPE POW/VOL KNOB RPT BUTTON USB INDICATOR SEEK/SKIP BAR RDM BUTTON CD/AUX BUTTON DISP BUTTON TUNE/FOLDER BAR SCAN BUTTON U.S. model is shown. Playing a USB Flash Memory Device (Models without na.
To Play a USB Flash Memory Device This audio system can operate the audio files on a USB flash memory device with the same controls used for the in-dash disc changer. To play a USB flash memory device, connect it to the USB adapter cable in the console compartment, then press the CD/AUX button.
The specifications for compatible MP3 files are: – Sampling frequency: 32/44.1/48 kHz (MPEG1) 24/22.05/16 kHz (MPEG2) – Bitrate: 32/40/48/56/64/80/96/112/128/ 160/192/224/256/320/VBR kbps (MPEG1) .
Connecting a USB Flash Memory Device 1. Push the release button to release the USB adapter cable. 2. Connect the USB flash memory device to the USB adapter cable correctly and securely. When the USB flash memory device is connected, the USB indicator is shown in the center display.
FOLDER SELECTION － To select a different folder, press and release either side of the TUNE/FOLDER bar. Press the side to skip to the next folder, and press the side to skip to the beginning of the previous folder. To Change or Select Files Use the SKIP bar while a USB flash memory device is playing to change files.
FOLDER REPEAT － This feature replays all the files in the selected folder in the order they are stored. To activate the folder repeat feature, press the RPT button repeatedly. You will see ‘‘ F-RPT ’’ in the center display. To turn it off, press and hold the RPT button.
Each time you press and release the SCAN button, the mode changes from file scan to folder scan, then to normal play. To Stop Playing a USB Flash Memory Device To play the radio, press the FM, AM or button. Press the CD/AUX button to switch between disc (if a disc is loaded) and Bluetooth ® Audio.
If you see an error message in the center display while playing a USB flash memory device, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. Error Message Cause Solution USB ERROR USB ROM error There is a problem with the USB adapter unit.
BLUETOOTH INDICATOR SEEK/SKIP BAR CD/AUX BUTTON PWR/VOL KNOB PRESET 1 BUTTON U.S. model is shown. Bluetooth ® Audio System (Models without navigation system) 212 09/07/07 15:02:04 10 ACURA RDX MMC No.
Your vehicle is equipped with a Bluetooth ® Audio system, which allows you to listen to streaming audio from your Bluetooth ® Audio compatible phone. This function is only available on Bluetooth ® Audio Compatible phones that are paired and linked to the vehicle's Bluetooth ® HandsFreeLink ® (HFL) system (see page 313 ).
In the following conditions, If you cannot see the Bluetooth ® indicator on the center display. ● The phone is not linked to HFL. ● The phone is not turned on. ● The phone is not in the vehicle. ● Another HFL compatible phone, which is not compatible for Bluetooth ® Audio, is already connected.
To turn off the Bluetooth ® Audio mode Select any other audio mode by pressing a button: FM, AM, or CD/AUX (if a disc is loaded), on the audio control panel or press the mode button on the steering wheel repeatedly to select another audio mode.
Interface Dial Most audio system functions can still be controlled by standard buttons, bars, and knob, but some functions can only be accessed using the interface dial.
U.S. model is shown. AUDIO CONTROL DISPLAY SCAN INDICATOR STEREO INDICATOR A.SEL INDICATOR RADIO BAND PRESET NUMBER UPPER DISPLAY CONTINUED Playing the FM/AM Radio (Models with navigation system) 217 .
U.S. model is shown. PRESET BUTTONS TUNE/FOLDER BAR AM/FM BUTTON PWR/VOL KNOB SCAN BUTTON SEEK/SKIP BAR INTERFACE DIAL AUDIO BUTTON Playing the FM/AM Radio (Models with navigation system) 218 09/07/07.
To Play the Radio The ignition switch must be in the ACCESSORY (I) or the ON (II) position. Press the AUDIO button to view the audio control display. Turn the system on by pressing the PWR/ VOL knob or the AM/FM button. Adjust the volume by turning the PWR/VOL knob.
To tune with the interface dial, press the AUDIO button to view the audio control display, then push the selector down, and turn the dial to TUNE. Then press ENTER on the selector, and turn the dial to the desired frequency. To exit the TUNE mode, press ENTER again.
To activate the scan function with the interface dial, press the AUDIO button to view the audio control display, then push down the selector on the interface dial, and push the selector to the right. You will see ‘‘ SCAN ’’ on the audio control display.
To store the frequency on a preset icon, turn the interface dial to select a desired preset icon. The selected preset icon will be highlighted. Press and hold ENTER on the selector for more than 2 seconds to store the frequency. 4. Repeat steps 1 through 3 to store a total of six stations on AM and twelve stations on FM.
If you do not like the stations auto select has stored, you can store other frequencies on the preset buttons (icons) as previously described. To turn off auto select, press ENTER on the interface selector again. This restores the presets you originally set.
Adjusting the Sound BASS, TREBLE, BALANCE, and FADER are each adjustable. You can also adjust the strength of the sound coming from the center and subwoofer speakers. In addition, you can set the Dolby PL (ProLogic) II and Speed-sensitive volume compensation (SVC).
The current setting is also shown on the upper display. The system will automatically return the display to the selected audio mode about 10 seconds after you stop adjusting a mode. BASS/TREBLE － To adjust bass and treble, select BASS or TREBLE, and press ENTER on the interface selector.
FADER/BALANCE － These modes adjust the strength of the sound coming from each speaker. Fader adjusts the front-to-back strength, while balance adjusts the side-to-side strength. To adjust fader and balance, select FADER or BALANCE, then press ENTER on the interface selector.
To set this feature on or off, select Dolby PL II, and press ENTER on the interface selector. Rotate the interface dial to ON or OFF, and press ENTER. Manufactured under license from Dolby Laboratories. ‘‘ Dolby ’’ , ‘‘ ProLogic ’’ , and the double-D symbol are trademarks of Dolby Laboratories.
U.S. model is shown. XM BAND PRESET NUMBER CHANNEL NUMBER CH MODE INDICATOR CATEGORY MODE INDICATOR Playing the XM ® Radio (Models with navigation system) 228 09/07/07 15:02:04 10 ACURA RDX MMC North.
SEEK/SKIP (CATEGORY) BAR SCAN BUTTON AUDIO BUTTON INTERFACE DIAL XM BUTTON DISP/MODE BUTTON TUNE/FOLDER BAR PRESET BUTTONS PWR/VOL KNOB U.S. model is shown.
Your vehicle is capable of receiving XM ® Radio anywhere in the United States and Canada, except Hawaii, Alaska, and Puerto Rico. XM is a registered trademark of Sirius XM Radio Inc. and XM CANADA ® is a registered business name of Canadian Satellite Radio Inc.
To Select a Channel When in the satellite radio mode, you can use any of four methods to find channels: TUNE, SEEK/SKIP (CATEGORY), SCAN, and the preset icons. You can also switch between the category mode and channel mode on the audio control display.
SCAN － The scan function gives you a sampling of all channels while in the channel mode. In the category mode, only the channels within that category are scanned. To activate scan, press the SCAN button. The system plays each channel in numerical order for a few seconds, then selects the next channel.
3. Pick a preset number for the channel you want to store. Press and hold the appropriate button until you hear a beep. To store the channel on a preset icon, rotate the interface dial to select a desired preset icon. The selected preset icon will be highlighted.
XM Radio Display Messages ‘‘ LOADING ’’ ꭚ XM is loading the audio or program information. ‘‘ OFF AIR ’’ ꭚ The channel currently selected is no longer broadcasting. ‘‘ UPDATING ’’ ꭚ The encryption code is being updated. Wait until the encryption code is fully updated.
Satellite Radio Signals Satellite radio receives signals from two satellites to produce clear, high- quality digital reception. It offers many channels in several categories. Along with a large selection of different types of music, satellite radio also allows you to view channel and category selections in the audio display.
Depending on where you drive, you may experience reception problems. Interference can be caused by any of these conditions: ● Driving on the north side of an east/west mountain road. ● Driving on the north side of a large commercial truck on an east/west road.
Note Function If equipped. This function stores the sound content played on the selected XM radio station with the channel, category, name, and title information. To activate this function, press and hold the button for about 2 seconds while a song or passage which you want to store is playing.
To delete a file, select it by turning the selector knob, then push it to the right. Select ‘‘ Delete All ’’ or ‘‘ Delete Selected Item, ’’ then press ENTER.
U.S. model is shown. Normal mode SCAN INDICATOR TRACK NUMBER SCAN INDICATOR WMA MODE INDICATOR DISC NUMBER MP3 MODE INDICATOR FOLDER NUMBER MP3/WMA mode CONTINUED Playing Discs (Models with navigation.
U.S. model is shown. AUDIO BUTTON DISC SLOT DISC/AUX BUTTON SCAN BUTTON LOAD BUTTON SEEK/SKIP BAR PRESET BUTTONS TUNE/FOLDER BAR EJECT BUTTON DISP/MODE BUTTON DISC LOAD INDICATOR PWR/VOL KNOB INTERFAC.
Your vehicle's audio system has an in-dash disc changer with the same controls used for the radio. To operate the disc changer, the ignition switch must be in the ACCESSORY (I) or the ON (II) position. The disc changer can play these disc formats: ● CD (CD-DA) ● CD-R/RW ● DVD-A The disc packages or jackets should have one of these marks.
Manufactured under license under U.S. Patent #'s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS, Inc.
2. Insert a disc into the disc slot when the disc load indicator turns green, and ‘‘ LOAD ’’ appears on the upper display at the same time. Insert the disc only about halfway; the drive will pull it in the rest of the way.
To Play a Disc Select the changer by pressing the DISC/AUX button. You will see the ‘‘ CD ’’ on the upper display. The system will begin playing the last selected CD in the CD changer. If you want to see the list of the discs in the CD changer, press the AUDIO button to view the audio control display.
Playing an MP3/WMA Disc The CD changer can also play CD-Rs and CD-RWs compressed in MP3 and WMA format. When playing a disc in MP3 or WMA, you will see ‘‘ MP3 ’’ or ‘‘ WMA ’’ on the upper display. A disc can support more than 99 folders, and each folder can hold up to 255 playable files.
The specifications for compatible WMA files are: – Sampling frequency: 32/44.1/48 kHz – Bitrate: 48/64/80/96/128/160/192 kbps – Compatible with variable bitrate and multi-session – Maximum lay.
You can also change tracks/files on the audio control display. Press the AUDIO button to view the display, then push the selector on the interface dial to the right to skip forward to the beginning of the next track/file. Push the selector left to skip backward to the beginning of the current track/file.
In MP3/WMA mode You will see a list of the folder(s) on the current disc. To select a folder (s), rotate the interface dial or push up and down the selector on the interface dial. Then press ENTER on the selector to enter your selection. If the disc has several folders, the list advances to the next folder.
DISC REPEAT － This feature, when activated, continuously replays the current CD. Press the AUDIO button to view the audio control display, then push down the selector on the interface dial. Rotate the interface dial to select the DISC REPEAT. Press ENTER on the selector to enter your selection.
To activate the scan feature on the audio control display, press the AUDIO button to view the display. Push down the selector on the interface dial, then push the selector to the left. You will see ‘‘ SCAN ’’ next to the TRACK icon on the audio control display.
DISC SCAN － The disc scan function samples the first track/file (in MP3/WMA mode) on each disc within the changer in numerical order. To activate this feature, press the SCAN button twice. In the MP3/ WMA mode, press the SCAN button three times. The first track/file on each disc plays for about 10 seconds.
You will see ‘‘ RANDOM ’’ next to the TRACK/FILE icon on the audio display. To turn off this feature, select TRACK RANDOM, then press ENTER again. In MP3/WMA mode FOLDER RANDOM － This feature plays the files within a folder in random order, rather than in the order they are compressed in MP3/ WMA.
Playing a DVD-A Disc You can play a DVD-A disc in the CD changer. The disc controls are same as previously described. To Pause a Disc To pause a disc, press the preset button which corresponds to the current disc. To play the disc again, press the preset button again.
To remove a different disc from the changer, first select it by pressing the corresponding number on the preset button or turning the interface knob, and pressing ENTER on the interface selector. When that disc begins playing, press the eject button. Press and hold the eject button until you hear a beep to remove all the discs from the changer.
If you see an error message in the display while playing a CD, find the cause in the chart to the right. If you cannot clear the error message, take the vehicle to your dealer. Error Message Cause Solution FOCUS Error Press the EJECT button, and pull out the disc.
The chart on the right explains the error messages you may see in the display while playing a disc. If you see an error message in the display while playing a disc, press the eject button. After ejecting the disc, check it for damage or deformation. If there is no damage, insert the disc again.
General Information ● When using CD-R/CD-RW discs, use only high quality CDs labeled for audio use. ● When recording a CD-R/CD-RW, the recording must be closed for it to be used by the system. ● Play only standard round CDs. Odd-shaped CDs may jam in the drive or cause other problems.
Additional Information on Recommended Discs The in-dash disc player/changer has a sophisticated and delicate mechanism. If you insert a damaged disc as indicated in this section, it may become stuck inside and damage the audio unit. Examples of these discs are shown to the right: 1.
4. Small, irregular shaped discs 5. Discs with scratches, dirty discs ● CD-R or CD-RW may not play due to the recording conditions. ● Scratches and fingerprints on the discs may cause the sound to skip. ● Recommended discs are printed with the following logo.
iPOD INDICATOR USB INDICATOR U.S. model is shown . Playing an iPod (Models with navigation system) 260 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
U.S. model is shown. AUDIO BUTTON DISC/AUX BUTTON SEEK/SKIP BAR PWR/VOL KNOB INTERFACE DIAL CONTINUED Playing an iPod (Models with navigation system) 261 Features 09/07/07 15:02:04 10 ACURA RDX MMC No.
To Play an iPod ® This audio system can operate the audio files on the iPod ® with the same controls used for the in-dash disc changer. To play an iPod, connect it to the USB adapter cable in the console compartment by using your dock connector, then press the DISC/AUX button.
Connecting an iPod 1. Push the release button to release the USB adapter cable. 2. Connect your dock connector to the iPod correctly and securely. 3. Install the dock connector to the USB adapter cable securely. If the iPod indicator does not appear in the audio display, check the connections, and try to reconnect the iPod a few times.
To Change or Select Files Use the SKIP bar while an iPod is playing to select passages and change files. SKIP － Each time you press and release the side of the SEEK/ SKIP bar, the system skips forward to the beginning of the next file. Press and release the side of the bar, to skip backward to the beginning of the current file.
Push ENTER on the selector to display the items on that list, then turn the knob on the interface dial to select a desired list. Pushing the selector up or down moves a selection to the top or bottom of the screen items. Press ENTER to set your selection.
To cancel the selected mode, press ENTER again while the highlighted mode is selected on the audio control display. REPEAT － This feature continuously plays a file. To turn it off, press ENTER again. Pressing either side of the SKIP bar changes the file while keeping the repeat feature.
ALBUM RANDOM － This feature plays all available albums from the selected items in the iPod menu list (playlists, artists, albums or songs) in random order. The files in each album are played in the recorded order. You will see ALBUM RANDOM on the screen.
Disconnecting an iPod You can disconnect the iPod at any time when you see the ‘‘ OK to disconnect ’’ message ꭧ in the iPod display. Always make sure you see the ‘‘ OK to disconnect ’’ message in the iPod display before you disconnect it.
If you see an error message on the upper display while playing an iPod, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. Error Message Cause Solution USB ERROR USB ROM error There is a problem with the USB adapter unit.
USB INDICATOR U.S. model is shown . FILE TYPE Playing a USB Flash Memory Device (Models with navigation system) 270 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010.
U.S. model is shown. U.S. model is shown. AUDIO BUTTON DISC/AUX BUTTON SCAN BUTTON SEEK/SKIP BAR TUNE/FOLDER BAR PWR/VOL KNOB INTERFACE DIAL CONTINUED Playing a USB Flash Memory Device (Models with na.
To Play a USB Flash Memory Device This audio system can operate the audio files on a USB flash memory device with the same controls used for the in-dash disc changer. To play a USB flash memory device, connect it to the USB adapter cable in the console compartment, then press the DISC/AUX button.
The specifications for compatible MP3 files are: – Sampling frequency: 32/44.1/48 kHz (MPEG1) 16/22.05/24 kHz (MPEG2) – Bitrate: 32/40/48/56/64/80/96/112/128/ 160/192/224/256/320/VBR kbps (MPEG1) .
Connecting a USB Flash Memory Device 1. Push the release button to release the USB adapter cable. 2. Connect the USB flash memory device to the USB adapter cable correctly and securely. When the USB device is connected and the USB mode is selected on the audio system, the USB indicator is shown in the upper display.
You can also change files with the interface dial. Press the AUDIO button to show the audio control display. Push the selector knob to the right side to skip to the beginning of the next file, and to the left side to skip to the beginning of the current file.
Push up the selector on the interface dial to switch the display to the folder list, then turn the knob on the interface dial to select a folder. Press ENTER to change the display to the file list, then turn the knob on the interface dial to select a file.
Turn the knob on the interface dial to select a play mode: folder random, track random, folder repeat, track repeat. Press ENTER to set your selection. To cancel the selected mode, push down the selector to display the audio menu on the audio control display.
FOLDER SCAN － This function samples the first file in each folder in the order they are stored. To activate the folder scan feature, push the selector to the right repeatedly. You will see FOLDER SCAN on the screen. You will also see SCAN on the upper display and the folder number blinking.
If you see an error message on the upper display while playing a USB flash memory device, find the solution in the chart to the right. If you cannot clear the error message, take your vehicle to your dealer. Error Message Cause Solution USB ERROR USB ROM error There is a problem with the USB adapter unit.
BLUETOOTH INDICATOR U.S. model is shown. Bluetooth ® Audio System (Models with navigation system) 280 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
U.S. model is shown. U.S. model is shown. AUDIO BUTTON DISC/AUX BUTTON SEEK/SKIP BAR PWR/VOL KNOB INTERFACE DIAL DISP/MODE BUTTON CONTINUED Bluetooth ® Audio System (Models with navigation system) 28.
Your vehicle is equipped with a Bluetooth ® Audio system, which allows you to listen to streaming audio from your Bluetooth ® Audio compatible phone. This function is only available on Bluetooth ® Audio Compatible phones that are paired and linked to the vehicle's Bluetooth ® HandsFreeLink ® (HFL) system (see page 313 ).
Once a device is linked, the name of the device will appear on the screen. Pressing the DISP/MODE button switches the audio control display between the Bluetooth ® Audio and the device name. If more than one phone is paired to the HFL system, there will be a delay before the system begins to play.
To skip a file Press the side of the SKIP bar to skip forward to the next file, and press the side to skip backward to the beginning of the current file. Push the side again to skip to the previous file. You can also operate the skip function with the interface dial on the audio control display of the navigation screen.
To change soun d settings Press the AUDIO button, then push down the selector to display the audio menu. Turn the knob to switch the setting between the resume/ pause mode and the sound mode. Select SOUND, then press ENTER to set your selection. Turn the knob to select a sound mode, then press ENTER to set your selection.
As required by the FCC: This device compli es with Part 15 of the FCC rules. Operation is subj ect to the following two condition s: (1) This device may not cause harmful interference, and (2) this device must acce pt any interference received, including interference that may cause undesired operation.
FM/AM Radio Frequencies The radio can receive the complete AM and FM bands. Those bands cover these frequencies: AM band: 530 to 1,710 kHz FM band: 87.7 to 107.9 MHz Radio stations on the AM band are assigned frequencies at least 10 kHz apart (530, 540, 550).
Radio signals, especially on the FM band, are deflected by large objects such as buildings and hills. Your radio then receives both the direct signal from the station's transmitter, and the deflected signal. This causes the sound to distort or flutter.
Three controls for the audio system are mounted in the steering wheel hub. They let you control basic functions without removing your hand from the steering wheel. The VOL button adjusts the volume up ( ) or down ( ). Press the top or bottom of the button, hold it until the desired volume is reached, then release it.
If you are playing a disc, the system skips to the beginning of the next track (file in MP3 or WMA format) each time you press the top ( ＋ )o f the CH button. Press the bottom ( － ) to return to the beginning of the current track/file. Press it twice to return to the previous track/file.
The auxiliary input jack is on the disc changer unit. The system will accept auxiliary input from standard audio accessories. When the audio system is on and you plug in a mini-jack cable between a compatible audio unit and the jack, you will see AUX in the display and the system automatically switches to AUX mode.
Your vehicle's audio system will disable itself if it is disconnected from electrical power for any reason. To make it work again, you must enter a specific five-digit code with the preset bars or buttons (depending on models).
On models without navigation system To set the time, press the SOUND/ CLOCK button until you hear a beep, then release the button. The displayed time begins to blink. Change the hour by pressing the H (preset 4) side of the preset bar until the numbers advance to the desired time.
The security system helps to protect your vehicle and valuables from theft. The horn sounds and a combination of headlights, parking lights, side marker lights, and taillights flashes if someone attempts to break into your vehicle or remove the radio.
Compass Operation On models without navigation system The compass shows your direction of travel. It indicates eight directions. The compass is displayed on the center display when you turn the ignition switch to the ON (II) position.
Compass Calibration If the compass direction is blinking and the CAL indicator is shown, the compass is self-calibrating. The compass may need to be manually calibrated after exposure to a strong magnetic field. If the compass seems to be continually showing the wrong direction and is not self-calibrating, do the following.
2. Select ‘‘ CAL ’’ by pressing preset 1 to enter the calibration mode. If you want to cancel this mode, select ‘‘ R ’’ by pressing preset 3. The display will return to the normal display. 3. Select ‘‘ CAL START ’’ by pressing preset 1.
1. Press and hold the SOUND/ CLOCK and RPT buttons at the same time for about 2 seconds. You will hear a beep, then the center display will change to the compass setting mode as shown above. 2. Select ‘‘ ZONE ’’ by pressing preset 2 to enter the zone setting mode.
ꭧ Guam Island : Zone 8 ꭧ Puerto Rico : Zone 11 Compass 299 Features 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
Cruise control allows you to maintain a set speed above 25 mph (40 km/h) without keeping your foot on the accelerator pedal. It should be used for cruising on straight, open highways. It is not recommended for city driving, winding roads, slippery roads, heavy rain, or bad weather.
Changing the Set Speed You can increase the set cruising speed in any of these ways: ● Press and hold the RES/ACCEL button. When you reach the desired cruising speed, release the button. ● Push on the accelerator pedal. Accelerate to the desired cruising speed, then press the SET/ DECEL button.
Cancelling Cruise Control You can cancel cruise control in any of these ways: ● Tap the brake pedal. ● Push the CANCEL button on the steering wheel. ● Push the CRUISE button on the steering wheel. The cruise control will be canceled when the vehicle speed reaches about 25 mph (40 km/h) or less.
The HomeLink ® Universal Transceiver built into your vehicle can be programmed to operate up to three remote controlled devices around your home, such as garage doors, lighting, or home security systems.
If you are training the second or third buttons, go directly to step 1. HomeLink ® Universal Transceiver 304 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
HomeLink ® is a registered trademark of Johnson Controls, Inc. As required by the FCC: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) Th.
Bluetooth ® HandsFreeLink ® (HFL) allows you to place and receive phone calls using voice commands, without handling your cell phone. To use HFL, you need a Bluetooth- compatible cell phone. For a list of compatible phones, pairing procedures, and special feature capabilities: In the U.
Voice Control Tips ● Air or wind noise from the dashboard and side vents and all windows may interfere with the microphone. Adjust or close them as necessary. ● Press and release the HFL Talk button each time you want to make a command. After the beep, speak in a clear, natural tone.
Help Features ● To hear general HFL information, including help on pairing a phone or setting up the system, say ‘‘ Tutorial. ’’ ● For help at any time, including a list of available commands, say ‘‘ Hands free help.
A notification that there is an incoming call, or HFL is in use, will appear on the navigation screen when the audio system is on. When there is an incoming call, or HFL is in use, ‘‘ HANDSFREELINK ’’ will appear on the display. The Bluetooth ® indicator will also appear on the audio display when a phone is linked.
How to Use HFL The ignition switch must be in the ACCESSORY (I) or ON (II) position. ‘‘ Pair ’’ ‘‘ Phone Setup ’’ Press HFL Talk button ‘‘ Edit ’’ ‘‘ Delete ’’ ‘‘ L.
Press HFL Talk button ‘‘ Redial ’’ ‘‘ Transfer ’’ ‘‘ Mute ’’ ‘‘ Send ’’ ‘‘ Store ’’ ‘‘ Edit ’’ ‘‘ Delete ’’ ‘‘ Receive Contact ’’ ‘‘ List ’’ ‘‘ Phonebook ’’ Press and release the HFL Talk button each time you give a command.
Press HFL Talk button ‘‘ System Set up ’’ ‘‘ Security ’’ ‘‘ Change Passcode ’’ ‘‘ Call Notification ’’ ‘‘ Auto Transfer ’’ ‘‘ Clear ’’ ‘‘ Change Language ’’ ‘‘ Tutorial ’’ ‘‘ Hands Free Help ’’ Press and release the HFL Talk button each time you give a command.
To use HFL, you need to pair your Bluetooth-compatible cell phone to the system. Phone Setup This command group is available for paired cell phones. Phone pairing tips ● You cannot pair your phone while the vehicle is moving. ● Your phone must be in discovery or search mode to pair.
To rename a paired phone: Press and release the HFL Talk button before a command. 1. Say ‘‘ Phone setup . ’’ 2. Say ‘‘ Edit ’’ after the prompts. 3. If there is more than one phone paired to the system, HFL will ask you which phone ’ s name you want to change.
To hear which paired phone is currently linked: Press and release the HFL Talk button before a command. 1. Say ‘‘ Phone setup . ’’ 2. Say ‘‘ Status ’’ after the prompts.
Making a Call You can make calls using any phone number or a name in the HFL phonebook. You can also redial the last number called. HFL uses a Class 2 Bluetooth, which means, the maximum range between your phone and vehicle is 30 feet (10 meters).
To make a call using the navigation display (on models with navigation system): 1. Press the INFO button, and the INFO screen will be shown. 2. From the INFO screen, select ‘‘ Cellular Phone, ’’ then select ‘‘ Dial. ’’ 3. The navigation display will change as shown above.
To redial the last number called by HFL: Press and release the HFL Talk button and say ‘‘ Redial . ’’ To make a call from an im ported phonebook: 1. From the INFO screen, select ‘‘ Cellular Phone . ’’ 2. Select ‘‘ Search Imported Phonebook .
To search for a specific name in the phonebook, enter the keyword for either the first or last name. To display all names in the phonebook, select the ‘‘ List ’’ option. 4. Select the name. All the phone numbers stored for that name will be listed.
Receiving a Call When you receive a call, an incoming call notification (if activated) will play and interrupt the audio system if it is on. Press the HFL Talk button to answer the call, or the HFL Back button to hang up.
Send Numbers or Names During a Call HFL allows you to send numbers or names during a call. This is useful when you call a menu-driven phone system. To send a nam e or number during a call: Press and release the HFL Talk button before a command. 1. Say ‘‘ Send.
To edit the number stor ed in a name: Press and release the HFL Talk button before a command. 1. Say ‘‘ Phonebook . ’’ 2. Say ‘‘ Edit ’’ after the prompts. 3. Follow the HFL prompts and say the name entry you want to edit. 4. When asked, say the new number for that name.
To store a specific phone number from your cell phone directly to the HFL phonebook (available on some phones): Press and release the HFL Talk button before a command. 1. Say ‘‘ Phonebook . ’’ 2. Say ‘‘ Receive contact ’’ after the prompts.
Search Imported Phonebo ok: Once a phonebook has been imported, you can search the phone numbers by the person ’ s name. Select ‘‘ Search Imported Phonebook , ’’ and a list of imported phonebooks will be displayed. Select a phonebook from the list.
Select a person from the list. Up to three category icons are displayed in the left side of the list: These category icons indicate how many numbers are stored for the name. If a name has more than three category icons, ‘‘ … ’’ is displayed.
Delete Imported Phone book: You can delete any imported phonebook. Select ‘‘ Delete Imported Phonebook, ’’ and a list of imported phonebooks will be displayed. Select a phonebook you want to delete. If the phonebook is PIN protected, you will need to enter the 4-digit PIN number.
To change the PIN to a new numbe r: Select the phonebook you want. The display will change as shown above. Enter the current PIN for this phonebook. The display will change as shown above. Enter the new 4-digit PIN number. You will be asked to re-enter the PIN for verification.
System Setup This command group allows you to change or customize HFL basic settings. To set a 4-digit passcode to lock the HFL system for security purposes: Press and release the HFL Talk button before a command. 1. Say ‘‘ System setup . ’’ 2.
To change your security pass code: Press and release the HFL Talk button before a command. 1. Say ‘‘ System setup . ’’ 2. Say ‘‘ Change passcode ’’ after the prompts. 3. Follow the HFL prompts and say the new 4-digit passcode. 4. Follow the HFL prompts to confirm the number.
To clear the system: This operation clears the passcodes, paired phones, all names in the HFL phonebook, and all imported phonebook data. Press and release the HFL Talk button before a command. 1. Say ‘‘ System setup . ’’ 2. Say ‘‘ Clear ’’ after the prompts.
Change Language Canadian models only To change the system language between English and French: Press and release the HFL Talk button before a command. 1. Say ‘‘ Change language . ’’ 2. Follow the HFL prompts to change the language to English or French.
On models with navigation system except Alaska, Hawaii, and Puerto Rico AcuraLink enhances your ownership experience by providing a direct communication link between your vehicle and the Acura Server.
Reading Messages If you have new messages, an envelope icon appears in the top right corner of the navigation screen. To open a message: ● Press ENTER on the interface selector, then select New Messages from the navigation system map menu. If there is more than one message stored in the system, you will see a list of message titles.
Select ‘‘ Messages ’’ , then select a message category. Select the message you want to read and press ENTER. Unread messages have a closed envelope icon next to them. The icon disappears when it has already been read. NOTE: Only diagnostic info messages overlay the screen while driving.
Deleting Messages NOTE: Diagnostic info and recall/ campaign messages can only be deleted by your dealer. To delete a single message: ● Press the INFO button to bring up the Information screen. ● Scroll to the Messages option, then select it by pressing ENTER on the interface selector.
Delete － Select this option to delete the current message. Voice － Select this option to hear a voice read the entire message. This gives you more information than the screen can display at one time. When you select the Voice option, it changes to a Stop Reading option.
AcuraLink/Message Screen To access the following functions, press the SETUP button, push the interface selector to the right to select MORE, then rotate the interface knob to select AcuraLink/ Messages. Delete Messages － Select this option to delete all stored messages within a category, except for diagnostic info and recall campaign messages.
NOTE: For the Phone Data Connection button to be active, you need a Bluetooth ® compatible and enabled cell phone paired to the Bluetooth ® HandsFreeLink ® (HFL). To complete the data connection setup, the paired phone must have a compatible data service.
Quick Tips These messages, based on updated vehicle information and comments from other RDX owners, supplement your Owner's Manual and Advanced Technology Guide. They provide you with relevant information for a safe and enjoyable ownership experience.
You can use the following message options: ● Make an appointment from the schedule at the dealer. ● Reschedule the appointment with the dealer. ● Call your dealer for an appointment.
Select the received message, then press ENTER. You will see the message as shown. To make an appointment, select ‘‘ Schedule Dealer Appt. ’’ then press ENTER. The system will automatically connect to the Acura server, then show you an appropriate appointment date and time on the navigation screen.
Scheduled Dealer Appointment To reschedule the appointment: Press the INFO button to go to the information screen, select ‘‘ Messages, ’’ and select ‘‘ Scheduled Dealer Appointment ’’ from the message category list. Then press ENTER. You will see the screen to reschedule as shown.
The system will request you to confirm the cancel on the navigation screen. To cancel the appointment, select ‘‘ YES, ’’ then press ENTER. If you select ‘‘ NO, ’’ the screen goes back to the previous message display. The system will automatically connect to the Acura server, then show you the confirmation on the navigation screen.
Using automated appointment, your registered dealer through Owner Link is automatically selected. If you want to select another dealer, such as in case of an emergency, find the nearest dealer and call the dealer directly with HFL. When a maintenance appointment is due soon, you will also receive an appointment reminder message.
Diagnostic Info When an indicator comes on or a message is displayed on the Multi- Information Display (MID), AcuraLink can provide information about the cause of the indicator or message and the recommended action to address it. This helps you handle the problem as it occurs, preventing or limiting costly repairs.
You will see information from the onboard troubleshooting database. You can then use message options to call your dealer for an appointment, to find the nearest dealer, or to find out more information about the issue.
When you make an appointment through My Acura's online Schedule Service Appointment, you can be reminded in advance about that appointment through AcuraLink.
On models with nav igation system Refer to the navigation system manual for operation of the rearview camera. On models wi thout navigation sys tem You can turn the camera display on and off by pressing the power button when the shift lever is in reverse.
If the engine has just been started, it may take a short time for the system to display the rearview. The camera display brightness is adjusted automatically by sensors. If you use the camera display continuously at high temperature, the image will gradually dim and eventually turn off automatically.
350 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
Before you begin driving your vehicle, you should know what gasoline to use and how to check the levels of important fluids. You also need to know how to properly store luggage or packages. The information in this section will help you. If you plan to add any accessories to your vehicle, please read the information in this section first.
Break-in Period Help assure your vehicle's future reliability and performance by paying extra attention to how you drive during the first 600 miles (1,000 km). During this period: ● Avoid full-throttle starts and rapid acceleration. ● Avoid hard braking for the first 200 miles (300 km).
Some gasoline today is blended with oxygenates such as ethanol or MTBE. Your vehicle is designed to operate on oxygenated gasoline containing up to 10% ethanol by volume and up to 15% MTBE by volume.
3. Remove the fuel fill cap slowly. You may hear a hissing sound as pressure inside the tank equalizes. Place the cap in the holder on the fuel fill door. 4. Stop filling the tank after the fuel nozzle automatically clicks off. Do not try to ‘‘ top off ’’ the tank.
Turn the engine off, and confirm the fuel fill cap is installed. If it is, loosen it, then retighten it until it clicks at least once. When you can restart the engine, the message appears again. The message goes off after several days of normal driving once you tighten or replace the fuel fill cap.
3. Holding the grip, pull the support rod out of its clip. Insert the end into the designated hole in the hood. To close the hood, lift it up slightly to remove the support rod from the hole. Put the support rod back into its holding clip. Lower the hood to about a foot (30 cm) above the fender, then let it drop.
Make sure the ‘‘ UP ’’ mark on the loop is facing up when you insert the dipstick. 4. Remove the dipstick again, and check the level. It should be between the upper and lower marks. If it is near or below the lower mark, see Adding Engine Oil on page 420 .
Actual Mileage and EPA Fuel Economy Estimates Comparison. Fuel economy is not a fixed number. It varies based on driving conditions, driving habits and vehicle condition. Therefore, it is not possible for one set of estimates to predict fuel economy precisely for all drivers in all environments.
Fuel Economy Factors The following factors can lower your vehicle's fuel economy: ● Aggressive driving (hard acceleration and braking) ● Excessive idling, accelerating and braking in stop-and.
Drive Efficiently ● Drive moderately － Rapid acceleration, abrupt cornering, and hard braking increase fuel consumption. ● Observe the speed limit － Aerodynamic drag has a big effect on fuel economy at speeds above 45 mph (75 km/h). Reduce your speed and you reduce the drag.
Calculating Fuel Economy Measuring Techniques Direct calculation is the recommended source of information about your actual fuel economy. Using frequency of fill-ups or taking fuel gauge readings are NOT accurate measures of fuel economy. Fuel economy may improve over the first several thousand miles.
Modifying your vehicle, or installing some non-Acura accessories, can make your vehicle unsafe. Before you make any modifications or add any accessories, be sure to read the following information. Accessories Your dealer has Acura accessories that allow you to personalize your vehicle.
Modifying Your Vehicle Removing parts from your vehicle, or replacing components with non- Acura components could seriously affect your vehicle's handling, stability, and reliability.
Your vehicle has several convenient storage areas: ● Glove box ● Front door pockets ● Door lining pockets ● Seat-back pockets ● Center pocket ● Console compartment ● Cargo area, including the rear seats when folded down.
Load Limits The maximum load for your vehicle is 870 lbs (395 kg). See Tire And Loading Information label attached to the driver's doorjamb. Label Example This figure includes the total weight of all occupants, cargo, and accessories, and the tongue load if you are towing a trailer.
5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
Carrying Cargo in the Passenger Compartment ● Store or secure all items that could be thrown around and hurt someone during a crash. ● Be sure items placed on the floor behind the front seats cann.
● If you carry large items that prevent you from closing the tailgate, exhaust gas can enter the passenger area. To avoid the possibility of carbon monoxide poisoning, follow the instructions on page 57 . ● ● If you carry any items on a roof rack, be sure the total weight of the rack and the items does not exceed 110 lbs (50 kg).
Optional Cargo Net The cargo net can be used to help hold down light items in the cargo area. The cargo net may not prevent heavy items from being thrown forward in a crash or a sudden stop. Heavy items should be secured to the cargo area floor with the hooks or cinch straps attached to the cargo hooks.
370 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
This section gives you tips on starting the engine under various conditions, and how to operate the automatic transmission. It also includes important information on parking your vehicle, the braking .
Your vehicle has higher ground clearance that allows you to travel over bumps, obstacles, and rough terrain. It also provides good visibility so you can anticipate problems earlier. Because your vehicle rides higher off the ground, it has a high center of gravity that can cause it to roll over if you make abrupt turns.
You should do these checks and adjustments before you drive your vehicle: 1. Make sure all windows, mirrors, and outside lights are clean and unobstructed. Remove frost, snow, or ice. 2. Check that the hood is fully closed. 3. Visually check the tires.
Your vehicle's starting system has an auto control mode. When you turn the ignition switch to the START (III) position, this feature keeps the engine's starter motor running until the engine starts. Follow these instructions to start the engine: 1.
Your vehicle has an electric vacuum pump located in the engine compartment. When you drive in cold weather or thinner air at high altitude, the electric vacuum pump operates more frequently after the engine is started. When the electric vacuum pump is in operation, it makes some mechanical noises come from the engine compartment.
Shift Lever Position Indicators These indicators on the instrument panel show which position the shift lever is in. The ‘‘ D ’’ indicator comes on for a few seconds when you turn the ignition switch to the ON (II) position. If it flashes while driving (in any shift position), it indicates a possible problem in the transmission.
To shift from: Do this: Pt oR Press the brake pedal, and press the shift lever release button. Rt oP Nt oR Dt oS Press the shift lever release button. St oD Dt oN Nt oD Rt oN Move the shift lever. Park (P) － This position mechanically locks the transmission.
Drive (D) － Use this position for your normal driving. The transmission automatically adjusts to keep the engine at the best speed for the driving conditions. S Position(S) － To shift into the S position, press the release button on the front of the shift lever, and move the lever to S.
Shift Lock Release This allows you to move the shift lever out of Park if the normal method of pushing on the brake pedal and pressing the release button does not work. 1. Set the parking brake. 2. Remove the key from the ignition switch. 3. Put a cloth on the notch of the shift lock release slot cover to prevent scratches.
Using the Paddle Shifters in the D position (D-Paddle Shift Mode) When you are driving in the D position, pulling either paddle shifter switches from the ordinary automatic transmission [drive mode (D)] to the D-paddle shift mode. You can shift the transmission up or down manually with the paddle shifters.
The transmission control system monitors the accelerator pedal use and your driving conditions. When you press the accelerator pedal as in normal driving, the system judges that you are driving at a constant cruising speed without using the paddle shifters.
Using the Paddle Shifters in the S position (Sequential Shift Mode) With the shift lever in the S position, you can select the sequential shift mode to shift gears; much like a manual transmission using the paddle shifters, but without a clutch pedal.
Downshifting with the paddle shifter allows you to increase the engine braking when going down steep or long hills, and provides more power when climbing uphills. You can upshift the transmission manually to reduce the rpm. The transmission also shifts automatically as the vehicle comes to a complete stop.
Starting in Second Gear When you are in sequential shift mode, and the vehicle is stopped, pull the ＋ (right) paddle shifter to shift to second gear. You will see ‘‘ M2 ’’ in the display. Starting in second gear helps to reduce wheelspin in deep snow or on a slippery surface.
Each torque indicator is displayed as a bar graph divided into 5 segments. The number of segments represents the amount of torque distributed to each wheel.
Always use the parking brake when you park your vehicle. Make sure the parking brake is set firmly, or your vehicle may roll if it is parked on an incline. Set the parking brake before you put the transmission in Park. This keeps the vehicle from moving and putting pressure on the parking mechanism in the transmission.
Your vehicle is equipped with disc brakes at all four wheels. A power assist using negative pressure generated by the engine and the electric vacuum pump helps reduce the effort needed on the brake pedal. The anti-lock brake system (ABS) helps you retain steering control when braking very hard.
The anti-lock brake system (ABS) helps prevent the wheels from locking up, and helps you retain steering control by pumping the brakes rapidly, much faster than a person can do it. The electronic brake distribution (EBD) system, which is part of the ABS, also balances the front-to-rear braking distribution according to vehicle loading.
If the ABS indicator and the brake system indicator come on together, and the parking brake is fully released, the EBD system may also be shut down. Test your brakes as instructed on page 467 . If the brakes feel normal, drive slowly and have your vehicle repaired by your dealer as soon as possible.
Your vehicle is equipped with a tire pressure monitoring system (TPMS) that turns on every time you start the engine and monitors the pressure in your tires while driving.
For example, if you check and fill your tires in a warm area, then drive in extremely cold weather, the tire pressure will be lower than measured and could be underinflated and cause the low tire pressure/ TPMS indicator to come on.
To see the inflation pressures of all four tires, press the SEL/RESET button. The display changes as shown above. Each tire pressure is shown in PSI (U.
If there is a problem with the TPMS, the tire pressure monitor shows a ‘‘ SYSTEM FUNCTION ERROR ’’ message and the tire pressure readings are not displayed. If this happens, you will first see a system warning message ‘‘ CHECK TPMS SYSTEM ’’ on the multi-information display.
Changing a Tire with TPMS If you have a flat tire, the low tire pressure/TPMS and tire monitor indicators will come on. Replace the indicated flat tire with the compact spare tire (see page 454 ). After the flat tire is replaced with the spare tire, the low tire pressure/ TPMS indicator stays on while driving.
The vehicle stability assist (VSA) system helps to stabilize the vehicle during cornering if the vehicle turns more or less than desired. It also assists you in maintaining traction while accelerating on loose or slippery road surfaces. It does this by regulating the engine's output and by selectively applying the brakes.
Without VSA, your vehicle will have normal braking and cornering ability, but it will not have VSA traction and stability enhancement. VSA OFF Switch In certain unusual conditions when your vehicle gets stuck in shallow mud or fresh snow, it may be easier to free it with the VSA temporarily switched off.
Your vehicle has been designed primarily to carry passengers and their cargo. You can also use it to tow a trailer if you carefully observe the load limits, use the proper equipment, and follow the guidelines in this section. Break-In Period Avoid towing a trailer during your vehicle's first 600 miles (1,000 km) (see page 352 ).
Tongue Load: The weight that the tongue of a fully-loaded trailer puts on the hitch should be approximately 10% of the total trailer weight. Too much tongue load reduces front-tire traction and steering control. Too little tongue load can make the trailer unstable and cause it to sway.
Checking Loads The best way to confirm that all loads are within limits is to check them at a public scale. For public scales in your area, check your local phone book, or contact your trailer dealer or rental agency for assistance.
Trailer Brakes Acura recommends that any trailer with a total trailer weight of 1,000 lbs (450 kg) or more has its own brakes. There are two common types of trailer brakes: surge and electric. Surge brakes are common for boat trailers, since the brakes will get wet.
Since lighting and wiring vary by trailer type and brand, you should have a qualified technician install a suitable connector between the vehicle and the trailer. Improper equipment or installation can cause damage to your vehicle's electrical system and affect your vehicle warranty.
● The trailer has been properly serviced and is in good condition. ● All weights and loads are within limits. ● The hitch, safety chains, and any other attachments are secure. ● All items in or on the trailer are properly secured and cannot shift while you drive.
Towing Speeds and Ge ars Drive slower than normal in all driving situations, and obey posted speed limits for vehicles with trailers. Use the D position when towing a trailer on level roads. See ‘‘ Driving on Hills ’’ in the next column for additional gear information.
Driving on Hills When climbing hills, closely watch your temperature gauge (see page 78 ). If it nears the H (Hot) mark, turn the A/C off, reduce speed and, if necessary, pull to the side of the road to let the engine cool.
General Information Your vehicle has been designed primarily for use on pavement. But its higher ground clearance and super handling-all wheel drive (SH-AWD) system allow you to occasionally travel on unpaved roads, to campgrounds, picnic sites, and similar locations.
Check Out Your Vehicle Before you leave the pavement, be sure to do all scheduled maintenance and service, and inspect your vehicle for any problems. Pay special attention to the condition of the tires, and check the tire pressures.
Crossing a Stream Avoid driving through deep water. If you encounter water in your route (a small stream or large puddle, for example), evaluate it carefully before going ahead. Make sure it is shallow, flowing slowly, and has firm ground underneath. If you are not sure of the depth or the ground, turn around and find another route.
408 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
This section explains why it is important to keep your vehicle well maintained and how to follow basic maintenance safety precautions. This section also includes instructions on how to read the maintenance minder messages on the multi-information display, and instructions for simple maintenance tasks you may want to take care of yourself.
All service items not detailed in this section should be performed by a certified technician or other qualified mechanic. Important Safety Precautions To eliminate potential hazards, read the instructions before you begin, and make sure you have the tools and skills required.
One of the most convenient and important features of the multi- information display on your vehicle is the maintenance minder. Based on engine operating conditions and accumulated engine revolutions, the onboard computer in your vehicle calculates the remaining engine oil life and displays it as a percentage.
When the remaining engine oil life is 15 to 6 percent, the multi-information display shows a ‘‘ SERVICE DUE SOON ’’ message along with the maintenance schedule code indicating the main and sub items required at the time of the oil change. Refer to page 418 for a complete list of the maintenance main items and sub items.
If the indicated maintenance service is not done and the remaining engine oil life reaches 0%, the multi- information display will show the message ‘‘ SERVICE PAST DUE ’’ and the maintenance item code(s). This message is displayed when the total distance traveled is less than 10 miles (for U.
If the indicated required service is not done and the remaining engine oil life becomes 0%, the multi- information display will show a ‘‘ SERVICE PAST DUE ’’ message, the total distance traveled after the remaining oil life became 0%, and the maintenance item code(s).
Maintenance Main Items and Sub Items All the maintenance items displayed on the multi-information display are in code. For an explanation of the maintenance codes, see page 418 . Resetting the Engine Oil Life Display Your dealer will reset the display after completing the required maintenance service.
4. Select ‘‘ RESET ’’ by pressing the INFO ( / ) button, then press the SEL/RESET button to reset the engine oil life display. The maintenance item code(s) will disappear, and the engine oil life will reset to ‘‘ 100. ’’ If you want to cancel the oil life reset mode, select ‘‘ CANCEL.
U.S. Vehicles: Maintenance, replacement, or repair of emissions control devices and systems may be done by any automotive repair establishment or individual using parts that are ‘‘ certified ’’ to EPA standards.
Symbol Maintenance Main Items A ● Replace engine oil ꭧ 1 B ● Replace engine oil ꭧ 1 and oil filter ● Inspect front and rear brakes ● Check parking brake adjustment ● Inspect these items:.
ENGINE OIL DIPSTICK (Orange loop) WASHER FLUID (Blue cap) POWER STEERING FLUID (Red cap) ENGINE COOLANT RESERVOIR RADIATOR CAP BRAKE FLUID (Black cap) AUTOMATIC TRANSMISSION FLUID DIPSTICK (Yellow loo.
Unscrew and remove the engine oil fill cap on top of the valve cover. Pour in the oil slowly and carefully so you do not spill any. Clean up any spills immediately. Spilled oil could damage components in the engine compartment. Reinstall the engine oil fill cap, and tighten it securely.
The oil viscosity or weight is provided on the container's label. 5W-30 oil is formulated for year- round protection of your vehicle to improve cold weather starting and fuel economy. Engine Oil Additives Your vehicle does not require any oil additives.
Always change the oil and filter according to the maintenance messages shown on the multi- information display. The oil and filter collect contaminants that can damage your engine if they are not removed regularly. Changing the oil and filter requires special tools and access from underneath the vehicle.
6. Put a new washer on the drain bolt, then reinstall the drain bolt. Tighten the drain bolt to: 29 lbf·ft (40 N·m , 4.0 kgf·m) 7. Refill the engine with the recommended oil. Engine oil change capacity (including filter): 5.0 US qt (4.7 L) 8. Reinstall the engine oil fill cap.
Adding Engine Coolant If the coolant level in the reserve tank is at or below the MIN line, add coolant to bring it up to the MAX line. Inspect the cooling system for leaks. Always use Honda Long-life Anti- freeze/Coolant Type 2. This coolant is pre-mixed with 50 percent antifreeze and 50 percent water.
1. Make sure the engine and radiator are cool. 2. Relieve any pressure in the cooling system by turning the radiator cap counterclockwise, without pressing down. 3. Remove the radiator cap by pushing down and turning counterclockwise. 4. The coolant level should be up to the base of the filler neck.
Check the fluid level in the windshield washer reservoir at least monthly during normal use. On U.S. models: To check the windshield washer fluid level, open the hood and look at the windshield washer reservoir located behind the left headlight. You will see a ‘‘ 1/2 ’’ mark on the reservoir.
Do not use engine antifreeze or a vinegar/water solution in the windshield washer reservoir. Antifreeze can damage your vehicle's paint, while a vinegar/water solution can damage the windshield washer pump. Use only commercially-available windshield washer fluid.
3. Insert the dipstick all the way into the transmission securely as shown in the illustration. 4. Remove the dipstick and check the fluid level. It should be between the upper and lower marks.
Check the fluid level in the brake fluid reservoir monthly. Replace the brake fluid every 3 years, independent of distance traveled. Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not available, you should use only DOT 3 or DOT 4 fluid, from a sealed container, as a temporary replacement.
Check the level on the side of the reservoir when the engine is cold. The fluid should be between the UPPER LEVEL and LOWER LEVEL. If not, add power steering fluid to the UPPER LEVEL. Pour the fluid slowly and carefully so you do not spill any. Clean up any spills immediately; it could damage components in the engine compartment.
Headlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the cargo area or pull a trailer, readjustment may be required. Adjustments should be done by your dealer or another qualified technician.
Replacing a Front Turn Signal/ Parking Light Bulb 1. Open the hood. Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise. 2. Remove the bulb from the socket by pushing the bulb in and turning it counterclockwise until it unlocks.
3. Install the socket back into the headlight assembly. Turn it clockwise to lock it in place. 4. Turn on the lights to make sure the new bulb is working. Replacing Rear Bulbs (in Tailgate) 1. Open the tailgate. Place a cloth on the edge of the light assembly cover to prevent scratches.
5. Turn on the lights to make sure the new bulb is working. 6. Reinstall the socket into the light assembly by turning it clockwise until it locks. 7. Reinstall the light assembly cover.
6. Turn on the lights to make sure the new bulb is working. 7. Put the socket back into the light assembly, and turn it clockwise to lock it in place. 8. Install the rear light assembly in the rear pillar. Tighten the two bolts. Snap the bolt covers into position.
3. Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down. 4. Remove the bulb from the fog light assembly by turning it one-quarter turn counterclockwise. 5. Install the new bulb into the hole and turn it one-quarter turn clockwise to lock it in place.
3. Remove the socket from the light assembly by turning it one-quarter turn counterclockwise. 4. Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms. 5. Press the brake pedal to make sure the new bulb is working.
Cleaning the Seat Belts If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air-dry before you use the vehicle. Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly.
Audio Antenna Your vehicle is equipped with an antenna at the rear of the roof. Before using a ‘‘ drive-through ’’ car wash, remove the antenna by unscrewing it by hand.
Check the condition of the wiper blades at least every six months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used.
3. Remove the blade from the blade assembly: ● Find two tabs with a ‘‘ SET ’’ and ‘‘ ’’ mark on the wiper blade assembly. The opposite side of the ‘‘ ’’ mark is the direction you pull out the wiper blade. ● Pull out the blade by grabbing the end of it as shown in the above illustration.
6. Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place. 7. Make sure the blade is completely installed and that its edge is not bunched up. 8. Lower the wiper arm down against the windshield, the passenger's side first, then the driver's side.
3. Examine the new wiper blades. If they have no plastic or metal reinforcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade. 4. Slide the new blade into the wiper arm.
To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated. The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced.
If you check air pressures when the tires are hot (driven for several miles/kilometers), you will see readings 4 to 6 psi (30 to 40 kPa, 0.3 to 0.4 kgf/cm 2 ) higher than the cold readings. This is normal. Do not let air out to match the recommended cold air pressure.
Your tires have wear indicators molded into the tread. When the tread wears down, you will see a 1/2 inch (12.7 mm) wide band across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. A tire this worn gives very little traction on wet roads.
Tire Rotation To help increase tire life and distribute wear more evenly, rotate the tires according to the maintenance messages displayed on the multi-information display. Move the tires to the positions shown in the illustration each time they are rotated.
Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed. Always use the size and type of tires recommended in this owner's manual.
Tire Chains Mount tire chains on your tires when required by driving conditions or local laws. Install them only on the front tires. Because your vehicle has limited tire clearance, Acura strongly recommends using the chains listed below, made by Security Chain Company (SCC).
Check the condition of the battery monthly by looking at the test indicator window. The label on the battery explains the test indicator's colors. Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water.
On models without navigation system If your vehicle's battery is disconnected, or goes dead, the time setting will be reset to 1:00. To set the time again, follow the setting procedure (see page 293 ). If your vehicle's battery is disconnected or goes dead, the audio system will disable itself.
If you need to park your vehicle for an extended period (more than 1 month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors.
This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again.
Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced, and put it back on your vehicle as soon as you can. Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.
If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area that is far away from the traffic lanes. The vehicle can easily roll off the jack, seriously injuring anyone underneath.
5. Remove the tools, wing bolt and the jack. To remove the jack, turn the jack's end bracket counterclockwise to loosen it. 6. Loosen the five wheel nuts 1/2 turn with the wheel nut wrench. 7. Place the jack under the jacking point nearest the tire you need to change.
8. Use the extension and the wheel nut wrench as shown to raise the vehicle until the flat tire is off the ground. 9. Remove the wheel nuts, then remove the flat tire. Handle the wheel nuts carefully; they may be hot from driving. Place the flat tire on the ground with the outside surface facing up.
13. Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility. Tighten the wheel nuts to: 80 lbf·ft (108 N·m, 11 kgf·m) 14. Store the jack in its holder. Turn the jack's end bracket to lock it in place.
Diagnosing why the engine won't start falls into two areas, depending on what you hear when you turn the ignition switch to the START (III) position: ● You hear nothing, or almost nothing. The engine's starter motor does not operate at all, or operates very slowly.
The Starter Operates Normally In this case, the starter motor's speed sounds normal, or even faster than normal, when you turn the ignition switch to the START (III) position, but the engine does not run.
Although this seems like a simple procedure, you should take several precautions. A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby. Keep all sparks, open flames, and smoking materials away from the battery.
3. Connect one jumper cable to the positive ( ＋ ) terminal on your battery. Connect the other end to the positive ( ＋ ) terminal on the booster battery. 4. Connect the second jumper cable to the negative ( － ) terminal on the booster battery. Connect the other end to the grounding point as shown.
The reading of the vehicle's temperature gauge on the multi- information display should stay in the midrange. If it climbs to the H (Hot) mark, you should determine the reason (hot day, driving up a steep hill, etc.
5. Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you continue driving (see Emergency Towing on page 475 ). 6. If you do not find an obvious leak, check the coolant level in the radiator reserve tank.
Low Oil Pressure Indicator This indicator should never come on when the engine is running. If it starts flashing or stays on, the oil pressure has dropped very low or lost pressure. Serious engine damage is possible, and you should take immediate action.
If the indicator comes on while driving, it means one of the engine's emissions control systems may have a problem. Even though you may feel no difference in your vehicle's performance, it can reduce your fuel economy and cause increased emissions.
Brake System Indicator (Red) U.S. Canada The brake system indicator (red) normally comes on when you turn the ignition switch to the ON (II) position, and as a reminder to check the parking brake. It will stay on if you do not fully release the parking brake.
Brake System Indicator (Amber) U.S. Canada Your vehicle has an electric vacuum pump located in the engine compartment. It enhances the effectiveness of your vehicle's brake system more frequently when you drive in cold weather or thinner air at high altitude after the engine is started.
The vehicle's fuses are contained in three fuse boxes. The interior fuse box is on the driver's lower left side. The primary under-hood fuse box is in the engine compartment on the driver's side. To open it, push the tabs as shown. The secondary under-hood fuse box is next to the battery.
Checking and Replacing Fuses If something electrical in your vehicle stops working, the first thing you should check for is a blown fuse. Determine from the chart on pages 473 and 474 , or the diagram on the fuse box lid, which fuse or fuses control that device.
4. Check the smaller fuses in the under-hood fuse box and all the fuses in the interior fuse box by pulling out each one with the fuse puller provided on the back of the primary under-hood fuse box cover. 5. Look for a blown wire inside the fuse. If it is blown, replace it with one of the spare fuses of the same rating or lower.
Replacing a fuse with one that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replacement fuse with the proper rating for the circuit, install one with a lower rating.
INTERIOR FUSE BOX No. Amps. Circuits Protected 1 7.5 A Power Window / SH-AWD ꬕ 2 20 A Fuel Pump 3 15 A ACG 4 7.5 A ABS/VSA 5 15 A Heated Seat 6 20 A FR Fog Lights 7 7.5 A Driver's Power Seat Lumbar Support 8 10A RR Wiper No. Amps. Circuits Protected 9 7.
UNDER-HOOD FUSE BOXES PRIMARY SECONDARY Primary Fuse Box No. Amps. Circuits Protected 1 100 A Main Fuse 30 A SH-AWD ꬕ 2 80 A Option Main 50 A Ignition Switch Main 3 40 A ABS/VSA Motor 20 A ABS/VSA F.
If your vehicle needs to be towed, call a professional towing service or organization. Never tow your vehicle with just a rope or chain. It is very dangerous. (On SH-AWD models) The only way you can safely tow your vehicle is with flat-bed equipment. The operator will load your vehicle on the back of a truck.
Improper towing preparation will damage the transmission. Follow the above procedure exactly. If you cannot shift the transmission or start the engine, your vehicle must be transported with the front wheels off the ground.
The diagrams in this section give you the dimensions and capacities of your vehicle and the locations of the identification numbers. It also includes information you should know about your vehicle's tires and emissions control systems. Identification Numbers .
Your vehicle has several identifying numbers located in various places. The vehicle identification number (VIN) is the 17-digit number your dealer uses to register your vehicle for warranty purposes. It is also necessary for licensing and insuring your vehicle.
The engine number is stamped into the front of the engine block. The transmission number is on a label on top of the transmission. AUTOMATIC TRANSMISSION NUMBER ENGINE NUMBER Identification Numbers 47.
Dimensions Length 182.5 in (4,635 mm) Width 73.6 in (1,870 mm) Height 65.2 in (1,655 mm) Wheelbase 104.3 in (2,650 mm) Track Front 61.9 in (1,572 mm) Rear 62.6 in (1,590 mm) Weights Gross vehicle weight rating See the certification label attached to the driver's doorjamb.
Lights Headlights High 12 V － 60 W (HB3) Low ꭧ 12 V － 35 W (D2S) Front turn signal/parking lights 12 V － 24/2.2 CP (Amber) Front fog lights 12 V － 55 W (H11) Front side marker lights 12 V �.
The tires on your vehicle meet all U. S. Federal Safety Requirements. All tires are also graded for treadwear, traction, and temperature performance according to Department of Transportation (DOT) standards.
Temperature The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
The tires that came on your vehicle have a number of markings. Those you should be aware of are described below. Tire Size Whenever tires are replaced, they should be replaced with tires of the same size. Below is an example of tire size with an explanation of what each component means.
Glossary of Tire Terminology Cold Tire Pressure － The tire air pressure when the vehicle has been parked for at least three hours or driven less than 1 mile (1.6 km). Load Rating － Means the maximum load that a tire is rated to carry for a given inflation pressure.
Driving on a significantly under inflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability.
The burning of gasoline in your vehicle's engine produces several by- products. Some of these are carbon monoxide (CO), oxides of nitrogen (NOx), and hydrocarbons (HC). Gasoline evaporating from the tank also produces hydrocarbons. Controlling the production of NOx, CO, and HC is important to the environment.
Onboard Refueling Vapor Recovery The onboard refueling vapor recovery (ORVR) system captures the fuel vapors during refueling. The vapors are adsorbed in a canister filled with activated carbon. While driving, the fuel vapors are drawn into the engine and burned off.
The three way catalytic converters contain precious metals that serve as catalysts, promoting chemical reactions to convert the exhaust gasses without affecting the metals. The catalytic converters are referred to as three-way catalysts, since they act on HC, CO, and NOx.
Testing of Readiness Codes If you take your vehicle for an emissions test shortly after the battery has been disconnected or gone dead, it may not pass the test. This is because of certain ‘‘ readiness codes ’’ that must be set in the on- board diagnostics for the emissions systems.
8. Select a nearby lightly traveled major highway where you can maintain a speed of 50 to 60 mph (80 to 100 km/h) for at least 20 minutes. Drive on the highway in D. Do not use the cruise control. When traffic allows, drive for 90 seconds without moving the accelerator pedal.
492 09/07/07 15:02:04 10 ACURA RDX MMC North America Owner's M 50 31STK630 enu 2010 RDX.
Client Service Information ........... 494 Warranty Coverages ................... 495 Reporting Safety Defects (U.S. Vehicles) ........................
Acura dealership personnel are trained professionals. They should be able to answer all your questions. If you encounter a problem that your dealership does not solve to your satisfaction, please discuss it with the dealership's management. The service manager or general manager can help.
U.S. Owners Your new vehicle is covered by these warranties: New Vehicle Limite d Warranty － covers your new vehicle, except for the battery, emissions control systems, and accessories against defects in materials and workmanship.
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying American Honda Motor Co.
Purchasing Factory Authorized Manuals (U.S. only) The publications shown below can be purchased from Helm Incorporated. You can order by phone or online: ● Call Helm Inc. at 1-800-782-4356 (credit card orders only) ● Go online at www.helminc.com If you are interested in other years or models, contact Helm Inc.
A Accessories and Modifications .......................... 362 ACCESSORY (Ignition Key Position) ................................. 125 Accessory Power Sockets .......... 157 AcuraLink ® (U.S. models only) ....................................... 332 Additives, Engine Oil .
Bulb Replacement Back-up Lights ........................ 433 Brake Lights ........................... 433 Fog Lights ............................... 435 Front Parking Lights ............... 432 Front Side Marker Lights ........ 432 Headlights ........
D DANGER, Explanation of ............. iii Dashboard ............................... 3 , 62 Daytime Running Lights ............ 119 Dead Battery .............................. 461 Defects, Reporting Safety ........... 496 Defogger, Rear Window .......
Ethanol in Gasoline .................... 352 Evaporative Emissions Controls .................................. 487 Exhaust Emissions Controls ...... 488 Exhaust Fumes ...................... ...... 57 Expectant Mothers, Use of Seat Belts by ...........
Automatic Lighting Off ............ 118 Automatic Lighting On ............ 117 Daytime Running Lights ......... 119 High Beam Indicator ................ 69 High Beams, Turning on ......... 116 Lights On Indicator .................. 70 Low Beams, Turning on .
Introduction ................................... i iPod Error Messages .......... 203 , 269 iPod ® ................................... 197 , 260 J Jack, Tire ................................... 455 Jacking up the Vehicle ............... 455 Jump Starting .
Numbers, Identification ............. 478 O Octane Requirement, Gasoline ................................. 352 Odometer ..................................... 76 Odometer, Trip ...................... ...... 76 Off-Highway Driving Guidelines ...........
Rear Lights, Bulb Replacement ........................... 433 Rear Seat Folding Down ............. 138 Rear Window Defogger .............. 121 Rear Window Wiper and Washer ................................... 115 Rearview Mirror .......................
Service Intervals ......................... 411 Service Station Procedures ........ 353 Setting the Clock ........................ 293 SH-AWD ® ................................... 384 Indicator ................................... 70 Torque Distribution Monitor .
Taking Care of the Unexpected ............................ 453 Technical Descriptions DOT Tire Quality Grading (U.S. Vehicles) ............................. 482 Emissions Control Systems ..... 487 Three Way Catalytic Converter ........................
USB Flash Memory Device Error Messages ........................ 211 , 279 Used Oil, How to Dispose of ...... 423 V Vanity Mirror ............................. 158 Vehicle Capacity Load ................ 365 Vehicle Dimensions ................... 480 Vehicle Identification Number .
Gasoline: Premium unleaded gasoline, pump octane number of 91 or higher. Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the catalytic converter.
OWNER _______________________________________ __________________ _______________________ ____________________________________ ___________________ ADDRESS _____________________________________ ________.
Ein wichtiger Punkt beim Kauf des Geräts Acura 2010 RDX (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Acura 2010 RDX noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Acura 2010 RDX - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Acura 2010 RDX reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Acura 2010 RDX erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Acura 2010 RDX besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Acura 2010 RDX verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Acura 2010 RDX. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Acura 2010 RDX gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
