DE
Makita logo
Offizielle Bedienungsanleitung

Makita DUC252

128 Seiten·2.8 MB·Kettensäge·PDF·ENJA
Makita DUC252
Inhaltsverzeichnis 22 Abschnitte ENGLISH (Original instructions) · Explanation of general view · SPECIFICATIONS · END313-1 · … AnzeigenAusblenden
Page 1 of the Makita DUC252 user manual — END313-1
Seite 1 · Zum Vergrößern klicken
Seite 1

ENGLISH (Original instructions)

Explanation of general view

1 Red indicator 2 Button 3 Battery cartridge 4 Star marking 5 Battery indicator 6 Lock-off button 7 Switch trigger 8 Front hand guard 9 Lock 10 Unlock 11 Adjusting screw 12 Sprocket cover 13 Lever 14 Adjusting dial

15 Sprocket 16 Adjusting pin 17 Hole 18 Guide bar 19 Loosen 20 Tighten 21 Saw chain 22 Oil tank cap 23 Oil inspection window (for refilling the tank with oil) 24 Oil inspection window 25 Spike bumper 26 Felling area 27 Felling direction

28 Danger zone 29 Escape route 30 Guide bar cover 31 Battery cover 32 Cutting length 33 Distance between cutting edge and depth gauge 34 Minimum 3 mm 35 Side plate angle 36 Slotted screwdriver 37 Locking ring 38 Limit mark 39 Brush holder cap 40 Screwdriver

SPECIFICATIONS

ModelDUC252DUC302 Standard guide barGuide bar length250 mm300 mm Cutting length23 cm24 cm28 cm TypeSprocket nose barCarving barSprocket nose bar Standard saw chainType91PX25AP90PX Pitch9.5 mm (3/8")6.35 mm (1/4")9.5 mm (3/8") Gauge1.3 mm (0.05")1.3 mm (0.05")1.1 mm (0.043") No. of drive links406046 SprocketNumber of teeth696 Pitch9.5 mm (3/8")6.35 mm (1/4")9.5 mm (3/8") Overall length (without guide bar)316 mm Net weight*14.1 kg *24.6 kg4.7 kg Chain speed per minute8.3 m/s (500 m/min) Chain oil tank volume85 cm3 Rated voltageD.C. 36 VD.C. 36 V
  • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
  • Specifications and battery cartridge may differ from country to country. *1 Weight, with largest battery cartridge, without guide bar and chain, empty oil tank, according to EN ISO 11681-2. *2 Weight, with battery cartridge, guide bar, and chain, filled oil tank, according to EPTA-Procedure 01/2003. WARNING: Use appropriate combination of the guide bar and saw chain. Otherwise personal injury may result.

END313-1

Symbols The following show the symbols used for the equipment. Be sure that you understand their meaning before use.

  • Read instruction manual.
  • Wear eye protection.
  • Wear ear protection.
  • Wear a helmet, goggles and ear protection.
Page 2 of the Makita DUC252 user manual — GEB118-1
Seite 2 · Zum Vergrößern klicken
Seite 2

3. Hold the power tool by insulated gripping surfaces only, because the saw chain may contact hidden wiring. Saw chains contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. 4. Wear safety glasses and hearing protection. Further protective equipment for head, hands, legs and feet is recommended. Adequate protective clothing will reduce personal injury by flying debris or accidental contact with the saw chain. 5. Always keep proper footing. Slippery or unstable surfaces may cause a loss of balance or control of the chain saw. 6. When cutting a limb that is under tension be alert for spring back. When the tension in the wood fibers is released the spring loaded limb may strike the operator and/or throw the chain saw out of control. 7. Use extreme caution when cutting brush and saplings. The slender material may catch the saw chain and be whipped toward you or pull you off balance. 8. Carry the chain saw by the front handle with the chain saw switched off and away from your body. When transporting or storing the chain saw always fit the guide bar cover. Proper handling of the chain saw will reduce the likelihood of accidental contact with the moving saw chain. 9. Follow instructions for lubricating, chain tensioning and changing accessories. Improperly tensioned or lubricated chain may either break or increase the chance for kickback. 10. Keep handles dry, clean, and free from oil and grease. Greasy, oily handles are slippery causing loss of control. 11. Cut wood only. Do not use chain saw for purposes not intended. For example: do not use chain saw for cutting plastic, masonry or non- wood building materials. Use of the chain saw for operations different than intended could result in a hazardous situation. 12. Causes and operator prevention of kickback: Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a sudden reverse reaction, kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose con- trol of the saw which could result in serious personal injury. Do not rely exclusively upon the safety devices built into your saw. As a chain saw user, you should take several steps to keep your cutting jobs free from accident or injury. Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below:

  • Use appropriate protection for foot-leg and hand-arm.
  • This saw is to be used by properly trained operators only.
  • Do not expose to rain.
  • Maximum permissible cut length
  • Direction of chain travel
  • Saw chain oil adjustment
  • Only for EU countries Do not dispose of electric equipment or battery pack together with household waste material! In observance of the European Directives, on Waste Electric and Electronic Equipment and Batteries and Accumulators and Waste Batteries and Accumulators and their implementation in accordance with national laws, electric equipment and batteries and battery pack(s) that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

ENE090-1 Intended use The tool is intended for cutting branches / pruning trees. It is also suitable for tree service.

GEA010-1

General Power Tool Safety Warnings

Save all warnings and instructions for future reference.

GEB118-1

Cordless Chain Saw Safety Warnings: 1. Keep all parts of the body away from the saw chain when the chain saw is operating. Before you start the chain saw, make sure the saw chain is not contacting anything. A moment of inattention while operating chain saws may cause entanglement of your clothing or body with the saw chain. 2. When holding with both hands, always hold the chain saw with your right hand on the rear handle and your left hand on the front handle. Holding the chain saw with a reversed hand configuration increases the risk of personal injury and should never be done.

Cd Ni-MH Li-ion

Page 3 of the Makita DUC252 user manual — GEA010-1
Seite 3 · Zum Vergrößern klicken
Seite 3

– Maintain a firm grip, with thumbs and fingers encircling the chain saw handles, with both hands on the saw and position your body and arm to allow you to resist kickback forces. Kickback forces can be controlled by the operator, if proper precautions are taken. Do not let go of the chain saw.

3. Ensure safe positioning of the chain saw during car transportation to avoid fuel or chain oil leakage, damage to the tool and personal injury. 4. Regularly check the functionality of chain brake. 5. Do not fill the chain oil near fire. Never smoke when you fill the chain oil. 6. National regulation may restrict the use of the chain saw. 7. If the equipment gets heavy impact or fall, check the condition before continuing work. Check the controls and safety devices for malfunction. If there is any damage or doubt, ask our authorized service center for the inspection and repair. 8. Always activate the chain brake before starting the chain saw. 9. Hold the saw firmly in place to avoid skating (skid movement) or bouncing of the saw when starting a cut. 10. At the end of the cut, be careful to keep your balance due to the “drop”. 11. Take into account the direction and speed of the wind. Avoid sawdust and chain oil mist.

Makita DUC252 — GEA010-1 diagram (page 3)
Abb. 1
  • – Do not overreach and do not cut above shoulder height. This helps prevent unintended tip contact and enables better control of the chain saw in unexpected situations. – Only use replacement bars and chains specified by the manufacturer. Incorrect replacement bars and chains may cause chain breakage and/or kickback. – Follow the manufacturer’s sharpening and maintenance instructions for the saw chain. Decreasing the depth gauge height can lead to increased kickback. 13. Before starting work, check that the chain saw is in proper working order and that its condition complies with the safety regulations. Check in particular that:
  • The chain brake is working properly;
  • The run-down brake is working properly;
  • The bar and the sprocket cover are fitted correctly;
  • The chain has been sharpened and tensioned in accordance with the regulations; 14. Do not start the chain saw with the chain cover being installed on it. Starting the chain saw with the chain cover being installed on it may cause the chain cover to thrown out forward resulting in personal injury and damage to objects around the operator.

Protective equipment 1. In order to avoid head, eye, hand or foot injuries as well as to protect your hearing the following protective equipment must be used during operation of the chain saw: – The kind of clothing should be appropriate, i. e. it should be tight-fitting but not be a hindrance. Do not wear jewelry or clothing which could become entangled with bushes or shrubs. If you have long hair, always wear a hairnet! – It is necessary to wear a protective helmet when- ever working with the chain saw. The protective helmet is to be checked in regular intervals for damage and is to be replaced after 5 years at the latest. Use only approved protective helmets. – The face shield of the protective helmet (or the goggles) protects against sawdust and wood chips. During operation of the chain saw always wear a goggle or a face shield to prevent eye injuries. – Wear adequate noise protection equipment (ear muffs, ear plugs, etc.) – The protective jacket consists of 22 layers of nylon and protects the operator against cuts. It is always to be worn when working from elevated platforms (cherry pickers, lifts), from platforms mounted on ladders or when climbing with ropes. – The protective brace and bib overall is made of a nylon fabric with 22 layers and protects against cuts. We strongly recommend its use. – Protective gloves made of thick leather are part of the prescribed equipment and must always be worn during operation of the chain saw. – During operation of the chain saw safety shoes or safety boots fitted with anti skid sole, steel toe caps and protection for the leg must always to be worn. Safety shoes equipped with a protec- tive layer provide protection against cuts and ensure a secure footing. For working in trees the safety boots must be suitable for climbing tech- niques.

Top handle chainsaw specific safety warnings 1. This chain saw is designed especially for tree care and surgery. The chain saw is intended to be used by properly trained persons only. Observe all instructions, procedures and recommendations from the relevant professional organization. Otherwise fatal accidents may occur. It is recommend that always using a rising platform (cherry picker, lift) for sawing in trees. Rappelling techniques are extremely dangerous and require special training. The operators must be trained to become familiar with safety equipment usage and climbing techniques. Always use the appropriate belts, ropes and carabiners when working in trees. Always use restraining equipment for both the operator and the saw. 2. Perform cleaning and maintenance before storage in accordance with the instruction manual.

Page 4 of the Makita DUC252 user manual — ENC007-8
Seite 4 · Zum Vergrößern klicken
Seite 4

Vibration 1. Individuals with poor circulation who are exposed to excessive vibration may experience injury to blood vessels or the nervous system. Vibration may cause the following symptoms to occur in the fingers, hands or wrists: “Falling asleep” (numbness), tingling, pain, stabbing sensation, alter- ation of skin colour or of the skin. If any of these symptoms occur, see a physician! To reduce the risk of “white finger disease”, keep your hands warm during operation and well maintain the equipment and accessories.

Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room temperature at 10°C – 40°C (50°F – 104°F). Let a hot battery cartridge cool down before charging it. 4. Charge the battery cartridge once in every six months if you do not use it for a long period of time.

SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

ENC007-8

Installing or removing battery cartridge (Fig. 1)

IMPORTANT SAFETY INSTRUCTIONS

  • CAUTION:
  • Always switch off the tool before installing or removing of the battery cartridge.
  • Hold the tool and the battery cartridge firmly when installing or removing battery cartridge. Failure to hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a personal injury.

FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any conduc-

To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.

  • CAUTION:
  • Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
  • Do not install the battery cartridge forcibly. If the cartridge does not slide in easily, it is not being inserted correctly.

tive material. (2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or

rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F). 7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 8. Be careful not to drop or strike battery. 9. Do not use dropped or struck battery. 10. Follow your local regulations relating to disposal of battery.

Tool/battery protection system The tool is equipped with a tool/battery protection system. This system automatically cuts off power to the motor to extend tool and battery life. The tool will automatically stop during operation if the tool or battery are placed under one of the following conditions. In some conditions, the indicators light up.

Overload protection When the tool is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops without any indication. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart.

SAVE THESE INSTRUCTIONS.

Page 5 of the Makita DUC252 user manual — Checking the chain brake (Fig. 5)
Seite 5 · Zum Vergrößern klicken
Seite 5

Overheat protection for battery / tool When the battery/tool is overheated, the tool stops automatically without any indication. The tool does not start even if pulling the switch trigger. In this situation, let the battery/tool cool before turning the tool on again.

ASSEMBLY

Removing or installing saw chain (Fig. 8, 9, 10, 11, 12 & 13)

  • CAUTION:
  • Always wear gloves when installing or removing the saw chain.
  • The saw chain and the guide bar are still hot just after the operation. Let them cool down enough before carrying out any work on the tool.

Overdischarge protection (Fig. 3) When the remaining battery capacity gets low, the battery indicator blinks on the applicable battery side. By further use, the tool stops and the battery indicator lights up about 10 seconds. In this situation, charge the battery cartridge.

Switch action (Fig. 4)

To remove the saw chain, perform the following steps: 1. Press and fully open the lever until it stops. 2. Turn the adjusting dial to “–” direction to release the saw chain tension. 3. Turn the lever counterclockwise to loosen the sprocket cover until it comes off. 4. Remove the sprocket cover. 5. Remove the saw chain and guide bar from the chain saw.

To prevent the switch trigger from being accidentally pulled, a lock-off button is provided. To start the tool, depress the lock-off button and pull the switch trigger. Release the switch trigger to stop.

To install the saw chain, perform the following steps: 6. Make sure the direction of the chain. The arrow mark on the chain shows the direction of the chain. 7. Fit in one end of the saw chain on the top of the guide bar and the other end of it around the sprocket. 8. Rest the guide bar in place on the chain saw. 9. Turn the adjusting dial to “–” direction to slide the adjusting pin in the direction of arrow. 10. Place the sprocket cover on the chain saw so that the adjusting pin is positioned in a small hole in the guide bar. 11. Turn the lever clockwise fully and a quarter turn back to keep looseness for adjusting chain tension. 12. Turn the adjusting dial, and adjust the chain tension. 13. Turn the lever clockwise to secure the sprocket cover. 14. Press and return the lever to its original position.

Checking the chain brake (Fig. 5)

Hold the chain saw with both hands when switching it on. Hold the top handle with your right hand, the front handle with your left. The bar and the chain must not be in contact with any object. First press the lock-off button, then the switch trigger. The saw chain starts immediately.

Press the front hand guard forwards using the back of your hand. The saw chain must come to an immediate standstill.

Adjusting saw chain tension (Fig. 8 & 14) The saw chain may become loose after many hours of use. From time to time check the saw chain tension before use. 1. Press and fully open the lever until it clicks. Turn it counterclockwise a little to loosen sprocket cover lightly. 2. Lift up the guide bar tip slightly. 3. Turn the adjusting dial to adjust the saw chain tension. Tighten the saw chain until the lower side of the saw chain fits in the guide bar rail (see circle in the figure). 4. Keep holding the guide bar lightly and tighten the sprocket cover after adjusting the chain tension. Make sure that the saw chain does not loose at lower side. 5. Press and return the lever to its original position.

Checking the run-down brake Switch on the chain saw. Release the switch trigger completely. The saw chain must come to a standstill within one second.

Adjusting the chain lubrication (Fig. 6) You can adjust the oil pump feed rate with the adjusting screw. The amount of oil can be adjusted using the universal wrench.

Carabiner (rope attachment point) (Fig. 7) Carabiner (Rope attachment point) is for use of tool hanging. Before using carabiner, pull it out and tie it with a rope.

Make sure the saw chain fits snugly against the lower side of the bar.

Page 6 of the Makita DUC252 user manual — WORKING WITH THE CHAIN SAW
Seite 6 · Zum Vergrößern klicken
Seite 6
  • CAUTION:
  • Do not tighten the saw chain too much. Excessively high tension of saw chain may cause breakage of saw chain, wear of the guide bar and breakage of the adjusting dial.
  • A chain which is too loose can jump off the bar, and therefore presents an accident risk.
  • Carry out the procedure of installing or removing saw chain in a clean place free from sawdust and the like.

Pruning trees (Fig. 18, 19, 20 & 21)

  • CAUTION:
  • Keep all parts of the body away from the saw chain when the motor is operating.
  • Hold the chain saw firmly with both hands when the motor is running.
  • Do not overreach. Keep proper footing and balance at all times.

Bring the spike bumper into contact with the branch to be cut before switching on. Cutting without bringing the spike bumper into contact with the branch may cause the guide bar to wobble, resulting in injury to operator.

Spike bumper (optional accessory) (Fig. 15) To install spike bumper, perform the following steps: 1. Remove the sprocket cover, saw chain and guide bar as described in this instruction manual. 2. Fit the holes of spike bumper along with the holes on the chainsaw. 3. Tighten them firmly with screws.

When cutting thick branches, first make a shallow undercut and then make the finish cut from the top.

If you try to cut off thick branches from the bottom, the branch may close in and pinch the saw chain in the cut. If you try to cut off thick branches from the top without a shallow undercut, the branch may splinter. If you cannot cut the timber right through with a single stroke: Apply light pressure to the handle and continue sawing and draw the chain saw back a little; then apply the spike a little lower and finish the cut by raising the handle.

OPERATION

Lubrication (Fig. 16 & 17) Saw chain is automatically lubricated when the tool is in operation. Check the amount of remaining oil in the oil tank through the oil inspection window. To refill the tank, remove the cap from the oil tank opening. After refilling the tank, always screw the provided oil tank cap on the chain saw.

Bucking (Fig. 22, 23 & 24) For bucking cuts, rest the spike bumper shown in the figure on the wood to be cut. With the saw chain running, saw into the wood, using the top handle to raise the saw and the front one to guide it. Use the spike bumper as a pivot. Continue the cut by applying slight pressure to the front handle, easing the saw back slightly. Move the spike bumper further down the timber and raise the front handle again. When making several cuts, switch the chain saw off between cuts.

  • CAUTION:
  • When filling the chain saw with chain oil for the first time, or refilling the tank after it has been completely emptied, add oil up to the bottom edge of the filler neck. The oil delivery may otherwise be impaired.
  • As a saw chain oil, use oil exclusively for Makita chain saws or oil available in market.
  • Never use oil including dust and particles or volatile oil.
  • When pruning trees, use botanical oil. Mineral oil may harm trees.
  • Never force the chain saw when pruning trees.
  • Before cutting out, make sure that the provided oil tank cap is screwed in place.

Cut wood under tension on the pressure side (A) first. Then make the final cut on the tension side (B). This prevents the bar from becoming trapped.

Hold the chain saw away from the tree. Start it and wait until lubrication on saw chain is adequate. Bring the spike bumper into contact with the branch to be cut before switching on. Otherwise it may cause the guide bar to wobble, resulting in injury to operator. Saw the wood to be cut by just moving it down.

Limbing

When limbing, support the chain saw on the trunk if possible. Do not cut with the tip of the bar, as this presents a risk of kickback. Pay particular attention to branches under tension. Do not cut unsupported branches from below. Do not stand on the felled trunk when limbing.

WORKING WITH THE CHAIN SAW

  • CAUTION:
  • The first time user should, as a minimum practice, do cutting logs on a saw-horse or cradle.
  • When sawing precut timber use a safe support (saw horse or cradle). Do not steady the workpiece with your foot, and do not allow anyone else to hold or steady it.
  • Secure round pieces against rotation.

Burrowing and parallel-to-grain cuts (Fig. 25)

Perform parallel-to-grain cuts at as shallow an angle as possible. Carry out the cut as carefully as possible, as the spike bumper cannot be used.

Page 7 of the Makita DUC252 user manual — Sharpening the saw chain (Fig. 31)
Seite 7 · Zum Vergrößern klicken
Seite 7

Felling (Fig. 26, 27, 28 & 29)

MAINTENANCE

  • CAUTION:
  • Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.
  • Always wear gloves when performing any inspection or maintenance.
  • Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

Observe local regulations if you wish to fell a tree. – Before starting felling work, ensure that: (1) Only persons involved in the felling operation are

in the vicinity; (2) Any person involved has an unhindered path of

retreat through a range of approximately 45° either side of the felling axis. Consider the additional risk of tripping over electrical cables; (3) The base of the trunk is free of foreign objects,

Sharpening the saw chain (Fig. 31)

roots and branches; (4) No persons or objects are present over a

Sharpen the saw chain when: – Mealy sawdust is produced when damp wood is cut; – The chain penetrates the wood with difficulty, even when heavy pressure is applied; – The cutting edge is obviously damaged; – The saw pulls to the left or right in the wood. The reason for this behaviour is uneven sharpening of the saw chain, or damage to one side only.

  • distance of 2 1/2 tree lengths in the direction in which the tree will fall. – Consider the following with respect to each tree:
  • Direction of lean;
  • Loose or dry branches;
  • Height of the tree;
  • Natural overhang;
  • Whether or not the tree is rotten. – Consider the wind speed and direction. Do not carry out felling work if the wind is gusting strongly. – Trimming of root swellings: Begin with the largest swellings. Make the vertical cut first, then the horizontal cut. – Cut a scarf: The scarf determines the direction in which the tree will fall, and guides it. It is made on the side towards which the tree is to fall. Cut the scarf as close to the ground as possible. First make the horizontal cut to a depth of 1/5 – 1/3 of the trunk diameter. Do not make the scarf too large. Then make the diagonal cut. – Cut any corrections to the scarf across its entire width. – Make the back cut a little higher than the base cut of the scarf. The back cut must be exactly horizontal. Leave approximately 1/10 of the trunk diameter between the back cut and the scarf. The wood fibers in the uncut trunk portion act as a hinge. Do not cut right through the fibers under any circumstances, as the tree will otherwise fall unchecked. Insert wedges into the back cut in time. – Only plastic or aluminum wedges may be used to keep the back cut open. The use of iron wedges is prohibited. – Stand to the side of the falling tree. Keep an area clear to the rear of the falling tree up to an angle of 45° either side of the tree axis (refer to the “felling area” figure). Pay attention to falling branches. – An escape path should be planned and cleared as necessary before cuts are started. The escape path should extend back and diagonally to the rear of the expected line of fall as illustrated in figure.

Sharpen the saw chain frequently, but remove only a little material each time. Two or three strokes with a file are usually sufficient for routine resharpening. When the saw chain has been resharpened several times, have it sharpened in a MAKITA specialist repair shop.

Sharpening criteria: (Fig. 32 & 33) – All cutter length must be equal. Cutters of differing length prevent the chain from running smoothly, and may cause the chain to break. – Do not sharpen the chain once a minimum cutter length of 3 mm has been reached. A new chain must then be fitted. – The chip thickness is determined by the distance between the depth gauge (round nose) and the cut- ting edge. – The best cutting results are obtained with following distance between cutting edge and depth gauge.

Chain blade 90PX0.5 mm Chain blade 91PX: 0.65 mm Chain blade 25AP: 0.65 mm

WARNING: • An excessive distance increases the risk of kick-back. – The sharpening angle of 30° must be the same on all cutters. Differences in angle cause the chain to run roughly and unevenly, accelerate wear, and lead to chain breaks. – The side plate angle of the cutter is determined by the depth of penetration of the round file. If the spec- ified file is used properly, the correct side plate angle is produced automatically. – Side plate angle for each saw chain are as follows:

Chain blade 90PX75° Chain blade 91PX: 80° Chain blade 25AP: 85°

Carrying tool (Fig. 30) Always remove the battery cartridge from the tool and overlap the guide bar with the guide bar cover before carrying the tool. Also cover the battery cartridge with the battery cover.

Page 8 of the Makita DUC252 user manual — MAINTENANCE
Seite 8 · Zum Vergrößern klicken
Seite 8

File and file guiding (Fig. 34, 35 & 36) – Use a special round file (optional accessory) for saw chains to sharpen the chain. Normal round files are not suitable. – Diameter of the round file for each saw chain is as follows:

Replacing carbon brushes (Fig. 41 & 42) Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes.

Chain blade 90PX: 4.5 mm Chain blade 91PX: 4.0 mm Chain blade 25AP: 4.0 mm – The file should only engage the cutter on the forward stroke. Lift the file off the cutter on the return stroke. – Sharpen the shortest cutter first. Then the length of this shortest cutter becomes the standard for all other cutters on the saw chain. – Guide the file as shown in the figure. – The file can be guided more easily if a file holder (optional accessory) is employed. The file holder has markings for the correct sharpening angle of 30° (align the markings parallel to the saw chain) and limits the depth of penetration (to 4/5 of the file diam- eter).

Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps.

Storing tool Clean the tool before storing. Remove any chips and sawdust from the tool after removing the sprocket cover. After cleaning the tool, run it under no load to lubricate the saw chain and guide bar. Cover the guide bar with the guide bar cover. Remove oil from the oil tank to empty it and place the chain saw.

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be per- formed by Makita Authorized Service Centers, always using Makita replacement parts.

– After sharpening the chain, check the height of the depth gauge using the chain gauge tool (optional accessory). – Remove any projecting material, however small, with a special flat file (optional accessory). – Round off the front of the depth gauge again.

Cleaning guide bar (Fig. 37) Chips and sawdust will build up in the guide bar groove, clogging it and impairing oil flow. Always clean out the chips and sawdust when sharpening or replacing the saw chain.

Cleaning the oil discharge hole (Fig. 38) Small dust or particles may be built up in the oil discharge hole during operation. Small dust or particles built up in the oil discharge hole may impair the oil discharge flow and cause an insufficient lubrication on the whole saw chain. When a poor chain oil delivery occurs at the top of guide bar, clean the oil discharge hole as follows. Remove the battery cartridge from the tool. Remove the sprocket cover and saw chain from the tool. (Refer to the section titled “Installing or removing saw chain”.)

Remove the small dust or particles using a slotted screwdriver with a slender shaft or the like. Insert the battery cartridge into the tool. Pull the switch trigger to flow built-up dust or particles off the oil discharge hole by discharging chain oil. Remove the battery cartridge from the tool. Reinstall the sprocket cover and saw chain on the tool.

Replacing the sprocket (Fig. 39 & 40) Before fitting a new saw chain, check the condition of the sprocket.

Always fit a new locking ring when replacing the sprocket.

Page 9 of the Makita DUC252 user manual — MAINTENANCE
Seite 9 · Zum Vergrößern klicken
Seite 9

Instructions for periodic maintenance To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be performed regularly. Warranty claims can be recognized only if this work is performed regularly and properly. Failure to perform the prescribed maintenance work can lead to accidents! The user of the chain saw must not perform maintenance work which is not described in the instruction manual. All such work must be carried out by authorized service centre.

Before operation Everyday Every

month Annually Before storage

Inspection.

Cleaning.

Check at authorized service center.

Inspection.

Sharpening if necessary.

Inspection.

Remove from the chain saw.

Check the function.

Have it inspected regularly at authorized service center.

Chain lubrication Check the oil feed rate.

Switch trigger Inspection.

Lock-off button Inspection.

Oil tank cap Check tightness.

Chain catcher Inspection.

Screws and nuts Inspection.

Show 8 more labels / short text on this page
Operating · Every 3 · time Item · week · Chain Saw · Saw chain · Guide bar · Chain brake
Page 10 of the Makita DUC252 user manual — OPTIONAL ACCESSORIES
Seite 10 · Zum Vergrößern klicken
Seite 10

TROUBLE SHOOTING Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs.

Malfunction status Cause Action

Two battery cartridges are not installed. Install the charged battery cartridges.

Chain saw does not start.

Recharge the battery cartridge. If recharging is not effective, replace battery cartridge.

Battery problem (under voltage).

Chain does not run. Chain brake activated. Release chain brake.

Recharge the battery cartridge. If recharging is not effective, replace battery cartridge.

Motor stops running after a little use. Battery’s charge level is low.

Oil tank is empty. Fill the oil tank.

No oil on the chain.

Oil guide groove is dirty. Clean the groove.

Oil delivery is not adjusted properly. Adjust amount of oil delivery.

Battery cartridge is installed improperly.

Install the battery cartridge as described in this manual.

Recharge the battery cartridge. If recharging is not effective, replace battery cartridge.

It does not reach maximum RPM.

Battery power is dropping.

The drive system does not work correctly.

Ask your local authorized service center for repair.

Chain does not stop even the chain brake is activated: Stop the machine immediately!

Brake band worn down. Ask your local authorized service center for repair.

Loose guide bar or saw chain. Adjust the guide bar and saw chain tension.

Abnormal vibration: Stop the machine immediately!

Tool malfunction. Ask your local authorized service center for repair.

OPTIONAL ACCESSORIES

ENG905-1 Noise The typical A-weighted noise level determined according to EN60745:

Sound pressure level (LpA): 84.4 dB (A) Sound power level (LWA): 95.4 dB (A) Uncertainty (K): 2.5 dB (A)

If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.

ENG900-1 Vibration The vibration total value (tri-axial vector sum) determined according to EN60745:

  • Makita genuine battery and charger
  • Saw chain
  • Guide bar
  • Guide bar cover
  • File
  • Tool bag
Model DUC252 Work modecutting wood Vibration emission (a h ): 4.7 m/s 2
Uncertainty (K)1.5 m/s 2
Model DUC302 Work modecutting wood Vibration emission (a h ): 6.3 m/s 2
Uncertainty (K)1.5 m/s 2

Wear ear protection

Page 11 of the Makita DUC252 user manual — EC Declaration of Conformity
Seite 11 · Zum Vergrößern klicken
Seite 11
  • ENG901-1
  • The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another.
  • The declared vibration emission value may also be used in a preliminary assessment of exposure.
  • WARNING:
  • The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used.
  • Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

ENH030-4 For European countries only

EC Declaration of Conformity

We Makita Corporation as the responsible manufacturer declare that the following Makita machine(s): Designation of Machine: Cordless Chain Saw Model No./ Type: DUC252, DUC302 Specifications: see “SPECIFICATIONS” table. are of series production and Conforms to the following European Directives:

2000/14/EC, 2006/42/EC And are manufactured in accordance with the following standards or standardised documents:

EN ISO 11682-2 The EC-Type Examination Certificate No. 4813008.13004 The EC-Type Examination per 2006/42/EC was performed by:

DEKRA Testing and Certification GmbH Enderstraße 92b 01277 Dresden Germany Identification No. 2140 The technical documentation is kept by:

Makita International Europe Ltd. Technical Department, Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, England

The conformity assessment procedure required by Directive 2000/14/EC was in Accordance with annex V. Measured Sound Power Level: 95.4 dB (A) Guaranteed Sound Power Level: 98 dB (A)

20.12.2013

Director Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi, 446-8502, JAPAN

Tomoyasu Kato

Reparatur

Fehlerbehebung

Häufige Probleme, wahrscheinliche Ursachen und Lösungen.

ProblemMögliche UrsacheAbhilfe
Chain saw does not start.Two battery cartridges are not installed.Install the charged battery cartridges. p.10
Chain saw does not start.Battery problem (under voltage).Recharge the battery cartridge. If recharging is not effective, replace battery cartridge. p.10
Chain does not run.Chain brake activated.Release chain brake. p.10
Motor stops running after a little use.Battery’s charge level is low.Recharge the battery cartridge. If recharging is not effective, replace battery cartridge. p.10
No oil on the chain.Oil tank is empty.Fill the oil tank. p.10
No oil on the chain.Oil guide groove is dirty.Clean the groove. p.10
No oil on the chain.Oil delivery is not adjusted properly.Adjust amount of oil delivery. p.10
It does not reach maximum RPM.Battery cartridge is installed improperly.Install the battery cartridge as described in this manual. p.10
It does not reach maximum RPM.Battery power is dropping.Recharge the battery cartridge. If recharging is not effective, replace battery cartridge. p.10
It does not reach maximum RPM.The drive system does not work correctly.Ask your local authorized service center for repair. p.10
Chain does not stop even the chain brake is activated: Stop the machine immediately!Brake band worn down.Ask your local authorized service center for repair. p.10
Abnormal vibration: Stop the machine immediately!Loose guide bar or saw chain.Adjust the guide bar and saw chain tension. p.10
Abnormal vibration: Stop the machine immediately!Tool malfunction.Ask your local authorized service center for repair. p.10

Frage zu Makita DUC252 stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Makita DUC252

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Makita DUC252 PDF-Anleitung

128 Seiten·2.8 MB·Kettensäge·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…