
1 Red indicator 2 Button 3 Battery cartridge 4 Star marking 5 Lock-off button 6 Switch trigger 7 Sprocket cover 8 Knob 9 Cutter 10 Guide bar
11 Arrow 12 Spring 13 Sprocket 14 Hook 15 Hole 16 Oil tank cap 17 Oil inspection window 18 Oil tank opening 19 Tip guide 20 Lower guide
21 Scabbard (chain cover) 22 Push nut 23 Slotted bit screwdriver 24 Filter 25 Locking ring 26 Washer 27 Limit mark 28 Brush holder cap 29 Screwdriver
Guide bar length 115 mm
Cutting length 11.5 cm
Pitch 6.35 mm (1/4")
Gauge 1.3 mm (0.05")
No. of drive links 42
Number of teeth 9
Pitch 6.35 mm (1/4")
Overall length 422 mm
Net weight 2.5 kg 2.6 kg
Chain speed per minute (min–1) 4.8 m/s (290 m/min) 5.0 m/s (300 m/min)
Chain oil tank volume 80 cm3
Rated voltage D.C. 14.4 V D.C. 18 V
Cordless Chain saw safety warnings: 1. Keep all parts of the body away from the saw chain when the chain saw is operating. Before you start the chain saw, make sure the saw chain is not contacting anything. A moment of inatten- tion while operating chain saws may cause entan- glement of your clothing or body with the saw chain. 2. When holding with both hands, always hold the chain saw with your right hand on the rear han- dle and your left hand on the front handle. Hold- ing the chain saw with a reversed hand configuration increases the risk of personal injury and should never be done. 3. Hold the power tool by insulated gripping sur- faces only, because the saw chain may contact hidden wiring. Saw chains contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. 4. Wear safety glasses and hearing protection. Fur- ther protective equipment for head, hands, legs and feet is recommended. Adequate protective clothing will reduce personal injury by flying debris or accidental contact with the saw chain.
ENE090-1 Intended use The tool is intended for cutting branches / pruning trees. It is also suitable for tree service.
GEA010-1 General Power Tool Safety Warnings
Save all warnings and instructions for future reference.

5. Always keep proper footing. Slippery or unstable surfaces may cause a loss of balance or control of the chain saw. 6. When cutting a limb that is under tension be alert for spring back. When the tension in the wood fibers is released the spring loaded limb may strike the operator and/or throw the chain saw out of con- trol. 7. Use extreme caution when cutting brush and saplings. The slender material may catch the saw chain and be whipped toward you or pull you off bal- ance. 8. Carry the chain saw by the front handle with the chain saw switched off and away from your body. When transporting or storing the chain saw always fit the guide bar cover. Proper handling of the chain saw will reduce the likelihood of accidental contact with the moving saw chain. 9. Follow instructions for lubricating, chain ten- sioning and changing accessories. Improperly tensioned or lubricated chain may either break or increase the chance for kickback. 10. Keep handles dry, clean, and free from oil and grease. Greasy, oily handles are slippery causing loss of control. 11. Cut wood only. Do not use chain saw for pur- poses not intended. For example: do not use chain saw for cutting plastic, masonry or non- wood building materials. Use of the chain saw for operations different than intended could result in a hazardous situation. 12. Causes and operator prevention of kickback: Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a sudden reverse reaction, kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose con- trol of the saw which could result in serious personal injury. Do not rely exclusively upon the safety devices built into your saw. As a chain saw user, you should take several steps to keep your cutting jobs free from accident or injury. Kickback is the result of tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below: – Maintain a firm grip, with thumbs and fingers

– Do not overreach and do not cut above shoul-
der height. This helps prevent unintended tip contact and enables better control of the chain saw in unexpected situations. – Only use replacement bars and chains speci-
fied by the manufacturer. Incorrect replacement bars and chains may cause chain breakage and/ or kickback. – Follow the manufacturer’s sharpening and
Top handle chainsaw specific safety warnings 1. This chain saw is designed especially for tree care and surgery. The chain saw is intended to be used by properly trained persons only. Observe all instruc- tions, procedures and recommendations from the relevant professional organization. Otherwise fatal accidents may occur. It is recommend that always using a rising platform (cherry picker, lift) for sawing in trees. Rappelling techniques are extremely dan- gerous and require special training. The operators must be trained to become familiar with safety equip- ment usage and climbing techniques. Always use the appropriate belts, ropes and carabiners when working in trees. Always use restraining equipment for both the operator and the saw. 2. Perform cleaning and maintenance before storage in accordance with the instruction manual. 3. Ensure safe positioning of the chain saw during car transportation to avoid fuel or chain oil leakage, damage to the tool and personal injury. 4. Do not fill the chain oil near fire. Never smoke when you fill the chain oil. 5. National regulation may restrict the use of the chain saw.
encircling the chain saw handles, with both hands on the saw and position your body and arm to allow you to resist kickback forces. Kickback forces can be controlled by the operator, if proper precautions are taken. Do not let go of the chain saw.

6. If the equipment gets heavy impact or fall, check the condition before continuing work. Check the controls and safety devices for malfunction. If there is any damage or doubt, ask our authorized service center for the inspection and repair. 7. Hold the saw firmly in place to avoid skating (skid movement) or bouncing of the saw when starting a cut. 8. At the end of the cut, be careful to keep your balance due to the “drop”. 9. Take into account the direction and speed of the wind. Avoid sawdust and chain oil mist.
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instruc- tions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any conduc-
Protective equipment 1. In order to avoid head, eye, hand or foot injuries as well as to protect your hearing the following protective equipment must be used during oper- ation of the chain saw: – The kind of clothing should be appropriate, i. e. it
should be tight-fitting but not be a hindrance. Do not wear jewelry or clothing which could become entangled with bushes or shrubs. If you have long hair, always wear a hairnet! – It is necessary to wear a protective helmet when-
ever working with the chain saw. The protective helmet is to be checked in regular intervals for damage and is to be replaced after 5 years at the latest. Use only approved protective helmets. – The face shield of the protective helmet (or the
tive material. (2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or
goggles) protects against sawdust and wood chips. During operation of the chain saw always wear a goggle or a face shield to prevent eye inju- ries. – Wear adequate noise protection equipment
rain. A battery short can cause a large current flow, overheating, possible burns and even a break- down. 6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F). 7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 8. Be careful not to drop or strike battery. 9. Do not use a damaged battery. 10. Follow your local regulations relating to disposal of battery.
(ear muffs, ear plugs, etc.) – The protective jacket consists of 22 layers of
nylon and protects the operator against cuts. It is always to be worn when working from elevated platforms (cherry pickers, lifts), from platforms mounted on ladders or when climbing with ropes. – The protective brace and bib overall is made of
a nylon fabric with 22 layers and protects against cuts. We strongly recommend its use. – Protective gloves made of thick leather are part
of the prescribed equipment and must always be worn during operation of the chain saw. – During operation of the chain saw safety shoes
SAVE THESE INSTRUCTIONS.
or safety boots fitted with anti skid sole, steel toe caps and protection for the leg must always to be worn. Safety shoes equipped with a protective layer provide protection against cuts and ensure a secure footing. For working in trees the safety boots must be suitable for climbing techniques.
Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the bat- tery cartridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room tempera- ture at 10°C – 40°C (50°F – 104°F). Let a hot bat- tery cartridge cool down before charging it. 4. Charge the battery cartridge once in every six months if you do not use it for a long period of time.
SAVE THESE INSTRUCTIONS.
Vibration

ASSEMBLY
To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.
Loosen the screw by turning counterclockwise the knob until the sprocket cover comes off. (Fig. 4) Remove the sprocket cover. Remove saw chain and guide bar from the tool. Fit in one end of the saw chain on the top of guide bar. At this time, fit the saw chain as shown in the figure because it rotates in the direction of arrow. (Fig. 5) Place the saw chain so that the spring is positioned inside it and fit in the other end of saw chain around the sprocket as shown in the figure. (Fig. 6) While turning the guide bar counterclockwise, install it so that the end of guide bar contacts the spring. (Fig. 7) Insert the hook of sprocket cover into the hole in the tool and then place the sprocket cover on the tool. (Fig. 8) Turn the knob clockwise to tighten the screw firmly. (Fig. 9)
Adjusting saw chain tension (Fig. 10 & 11) Just a slight loosening of the screw allows the saw chain tension to be adjusted. After adjusting, retighten the screw firmly.
Spike bumper (optional accessory) (Fig. 12) To install spike bumper, perform the following steps: 1. Remove the sprocket cover, saw chain and guide bar as described in this instruction manual. 2. Fit the holes of spike bumper along with the holes on the chainsaw. 3. Tighten them firmly with screws.
Lubrication (Fig. 13) Saw chain is automatically lubricated when the tool is in operation. Check the amount of remaining oil in the oil tank through the oil inspection window. To refill the tank, remove the cap from the oil tank open- ing.
To prevent the switch trigger from being accidentally pulled, a lock-off button is provided. To start the tool, depress the lock-off button and pull the switch trigger. Release the switch trigger to stop.

After refilling the tank, always screw the provided oil tank cap on the chain saw.
Sharpen the saw chain when: – Mealy sawdust is produced when damp wood is cut; – The chain penetrates the wood with difficulty, even
when heavy pressure is applied; – The cutting edge is obviously damaged; – The saw pulls to the left or right in the wood. The rea-
son for this behaviour is uneven sharpening of the saw chain, or damage to one side only. (Fig. 20)
Sharpen the saw chain frequently, but remove only a little material each time. Two or three strokes with a file are usually sufficient for routine resharpening. When the saw chain has been resharpened several times, have it sharpened in a MAKITA specialist repair shop.
Hold the chain saw away from the tree. Start it and wait until lubrication on saw chain is adequate. Bring the tip guide/lower guide into contact with the branch to be cut before switching on. Cutting without bringing the tip guide/lower guide into contact with the branch may cause the guide bar to wobble, resulting in injury to operator. Saw the wood to be cut by just moving it down.
File and file guiding (Fig. 21) – Use a special round file (optional accessory) for saw
chains, with a diameter of 4 mm, to sharpen the chain. Normal round files are not suitable. – The file should only engage the material on the for-
ward stroke. Lift the file off the material on the return stroke. – Sharpen the shortest cutter first. The length of this
cutter is then the gauge dimension for all other cutters on the saw chain. – Guide the file as shown in the figure. – The file can be guided more easily if a file holder
(accessory) is employed. The file holder has markings for the correct sharpening angle of 30° (align the markings parallel to the saw chain) and limits the depth of penetration (to 4/5 of the file diameter).
Bring the tip guide/lower guide into contact with the branch to be cut before switching on. Cutting without bringing the tip guide/lower guide into contact with the branch may cause the guide bar to wobble, resulting in injury to operator. (Fig. 14 & 15) When cutting thick branches, first make a shallow under- cut and then make the finish cut from the top. (Fig. 16) If you try to cut off thick branches from the bottom, the branch may close in and pinch the saw chain in the cut. If you try to cut off thick branches from the top without a shallow undercut, the branch may splinter. (Fig. 17) If you cannot cut the timber right through with a single stroke: Apply light pressure to the handle and continue sawing and draw the chain saw back a little; then apply the spike a little lower and finish the cut by raising the handle. (Fig. 18)
Guide the file as shown in the figure. (Fig. 22) – After sharpening the chain, check the height of the
depth gauge using the chain gauge tool (optional accessory). – Remove any projecting material, however small, with a
special flat file (optional accessory). – Round off the front of the depth gauge again. – Wash away dust and particles from saw chain after
adjusting the height of depth gauge.
Cleaning guide bar (Fig. 23) Chips and sawdust will build up in the guide bar groove, clogging it and impairing oil flow. Always clean out the chips and sawdust when sharpening or replacing the saw chain.
Carrying tool (Fig. 19) Always remove the battery cartridge from the tool and overlap the guide bar with the scabbard before carrying the tool. Also cover the battery cartridge with the battery cover.
Cleaning the oil filter at the oil discharge hole Small dust or particles may be built up in the oil filter at the oil discharge hole during operation. Small dust or particles built up in the oil filter may impair the oil discharge flow and cause an insufficient lubrica- tion on the whole saw chain. When a poor chain oil delivery occurs at the top of guide bar, clean the filter as follows. Remove the battery cartridge from the tool. Remove the sprocket cover and saw chain from the tool. (Refer to the section titled “Installing or removing saw chain”.) Remove the push nut using a slotted bit screwdriver with a slender shaft or the like. (Fig. 24)

Take the filter out of the chain saw and remove small dust or particles from it. When the filter is too dirty, replace it with a new one. (Fig. 25) Insert the battery cartridge into the tool. Pull the switch trigger to flow built-up dust or particles off the oil discharge hole by discharging chain oil. (Fig. 26) Remove the battery cartridge from the tool. Insert the cleaned oil filter into the oil discharge hole. When the filter is too dirty, replace it with a new one. (Fig. 27) Insert the push nut with its correct side facing up as shown in the figure into the oil discharge hole to secure the filter. When the filter cannot be secured with a disfig- ured push nut, replace the push nut with a new one. (Fig. 28) Reinstall the sprocket cover and saw chain on the tool.
Replacing the sprocket (Fig. 29 & 30) Before fitting a new saw chain, check the condition of the sprocket.
Always fit a new locking ring when replacing the sprocket.
Replacing carbon brushes (Fig. 31 & 32) Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps.
Storing tool Clean the tool before storing. Remove any chips and sawdust from the tool after removing the sprocket cover. After cleaning the tool, run it under no load to lubricate the saw chain and guide bar. Cover the guide bar with the scabbard. Remove oil from the oil tank to empty it and place the chain saw with the tank cap facing upward. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be per- formed by Makita Authorized Service Centres, always using Makita replacement parts.

Instructions for periodic maintenance To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be performed regularly. Warranty claims can be recognized only if this work is performed regularly and properly. Failure to perform the pre- scribed maintenance work can lead to accidents! The user of the chain saw must not perform maintenance work which is not described in the instruction manual. All such work must be carried out by authorized service centre.
Before operation Everyday Every
month Annually Before storage
Inspection.
Cleaning.
Check at authorized service center.
Inspection.
Sharpening if necessary.
Inspection.
Remove from the chain saw.
Chain lubrication Check the oil feed rate.
Switch trigger Inspection.
Lock-off button Inspection.
Oil tank cap Check tightness.
Chain catcher Inspection.
Screws and nuts Inspection.

TROUBLE SHOOTING Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs.
Malfunction status Cause Action
Battery cartridge is not installed. Install the charged battery cartridge.
Recharge the battery cartridge. If recharging is not effective, replace battery cartridge.
Chain saw does not start.
Battery problem (under voltage).
Recharge the battery cartridge. If recharging is not effective, replace battery cartridge.
Motor stops running after a little use. Battery’s charge level is low.
Oil tank is empty. Fill the oil tank.
Oil guide groove is dirty. Clean the groove.
No oil on the chain.
Malfunction of oil pump. Ask your local authorized service center for repair.
Battery cartridge is installed improperly.
Install the battery cartridge as described in this manual.
Recharge the battery cartridge. If recharging is not effective, replace battery cartridge.
It does not reach maximum RPM.
Battery’s charge level is low.
The drive system does not work correctly.
Ask your local authorized service center for repair.
Chain does not stop: Stop the machine immediately! Malfunction of switch. Ask your local authorized service center for repair.
Loose guide bar or saw chain. Adjust the guide bar and saw chain tension.
Abnormal vibration: Stop the machine immediately!
Tool malfunction. Ask your local authorized service center for repair.
ENG905-1 Noise The typical A-weighted noise level determined according to EN60745:
Sound pressure level (LpA): 84.6 dB (A) Sound power level (LWA): 92.7 dB (A) Uncertainty (K): 2 dB (A)
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
ENG900-1 Vibration The vibration total value (tri-axial vector sum) determined according to EN60745:
Model DUC122 · Wear ear protection · Model DUC122

ENH030-5 For European countries only
Makita declares that the following Machine(s): Designation of Machine: Cordless Chain Saw Model No./ Type: DUC122 Specifications: see “SPECIFICATIONS” table. Conforms to the following European Directives:
2000/14/EC, 2006/42/EC They are manufactured in accordance with the following standard or standardized documents:
EN ISO 11681-2 The EC-Type Examination Certificate No. 4814056.14009 The EC-Type Examination per 2006/42/EC was per- formed by:
DEKRA Testing and Certification GmbH Enderstraße 92b 01277 Dresden Germany Identification No. 2140 The technical file in accordance with 2006/42/EC is avail- able from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
The conformity assessment procedure required by Direc- tive 2000/14/EC was in Accordance with annex V Measured Sound Power Level: 93 dB (A) Guaranteed Sound Power Level: 95 dB (A)
23.9.2014
Director Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
Yasushi Fukaya
Häufige Probleme, wahrscheinliche Ursachen und Lösungen.
| Problem | Mögliche Ursache | Abhilfe | |
|---|---|---|---|
| Chain saw does not start. | Battery cartridge is not installed. | Install the charged battery cartridge. | p.8 |
| Chain saw does not start. | Battery problem (under voltage). | Recharge the battery cartridge. If recharging is not effective, replace battery cartridge. | p.8 |
| Motor stops running after a little use. | Battery’s charge level is low. | Recharge the battery cartridge. If recharging is not effective, replace battery cartridge. | p.8 |
| No oil on the chain. | Oil tank is empty. | Fill the oil tank. | p.8 |
| No oil on the chain. | Oil guide groove is dirty. | Clean the groove. | p.8 |
| No oil on the chain. | Malfunction of oil pump. | Ask your local authorized service center for repair. | p.8 |
| It does not reach maximum RPM. | Battery cartridge is installed improperly. | Install the battery cartridge as described in this manual. | p.8 |
| It does not reach maximum RPM. | Battery’s charge level is low. | Recharge the battery cartridge. If recharging is not effective, replace battery cartridge. | p.8 |
| It does not reach maximum RPM. | The drive system does not work correctly. | Ask your local authorized service center for repair. | p.8 |
| Chain does not stop: Stop the machine immediately! | Malfunction of switch. | Ask your local authorized service center for repair. | p.8 |
| Abnormal vibration: Stop the machine immediately! | Loose guide bar or saw chain. | Adjust the guide bar and saw chain tension. | p.8 |
| Abnormal vibration: Stop the machine immediately! | Tool malfunction. | Ask your local authorized service center for repair. | p.8 |
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.