DE
Makita logo
Offizielle Bedienungsanleitung

Makita DJS100

48 Seiten·1.1 MB·Sonstiges·PDF·ENJA
Makita DJS100
Inhaltsverzeichnis 15 Abschnitte I Cesoie per metallo a batteria Istruzioni per l’uso · ENGLISH (Original instructions) · Explanation of general view · SPECIFICATIONS · … AnzeigenAusblenden
Page 1 of the Makita DJS100 user manual — I Cesoie per metallo a batteria Istruzioni per l’uso
Seite 1 · Zum Vergrößern klicken
Seite 1
Makita DJS100 — I Cesoie per metallo a batteria Istruzioni per l’uso diagram (page 1)
Abb. 1 · I Cesoie per metallo a batteria Istruzioni per l’uso

I Cesoie per metallo a batteria Istruzioni per l’uso

Makita DJS100 — I Cesoie per metallo a batteria Istruzioni per l’uso diagram (page 1)
Abb. 2 · I Cesoie per metallo a batteria Istruzioni per l’uso
Page 2 of the Makita DJS100 user manual — 7 010087 8 010084
Seite 2 · Zum Vergrößern klicken
Seite 2
Makita DJS100 — I Cesoie per metallo a batteria Istruzioni per l’uso diagram (page 2)
Abb. 3 · I Cesoie per metallo a batteria Istruzioni per l’uso

1 014128 2 012128

Makita DJS100 — 1 014128 2 012128 diagram (page 2)
Abb. 4

3 010088 4 010089

Makita DJS100 — 3 010088 4 010089 diagram (page 2)
Abb. 5

5 010085 6 010086

Makita DJS100 — 5 010085 6 010086 diagram (page 2)
Abb. 6

7 010087 8 010084

Page 3 of the Makita DJS100 user manual — 13 010093
Seite 3 · Zum Vergrößern klicken
Seite 3
Makita DJS100 — I Cesoie per metallo a batteria Istruzioni per l’uso diagram (page 3)
Abb. 7 · I Cesoie per metallo a batteria Istruzioni per l’uso

9 010090 10 010091

Makita DJS100 — 9 010090 10 010091 diagram (page 3)
Abb. 8

11 001145 12 010092

Makita DJS100 — 11 001145 12 010092 diagram (page 3)
Abb. 9

13 010093

Page 4 of the Makita DJS100 user manual — General Power Tool Safety Warnings GEA010-1
Seite 4 · Zum Vergrößern klicken
Seite 4

ENGLISH (Original instructions)

Explanation of general view

1. Button 2. Red indicator 3. Battery cartridge 4. Star marking 5. Switch lever 6. Indicating lamp 7. Hex wrench
8. Screw 9. Center blade 10. Thickness gauge 11. Side blade 12. Hex socket head bolt 13. Oil supply 14. Pin
15. Limit mark 16. Brush holder cover 17. Notch 18. Screwdriver 19. Brush holder cap

SPECIFICATIONS

ModelDJS160DJS161DJS100DJS101 Max. cutting capacitiesSteel up to 400 N/mm21.6 mm (16 ga.)1.0 mm (20 ga.) Steel up to 600 N/mm21.2 mm (18 ga.)0.7 mm (23 ga.) Aluminum up to 200 N/mm22.5 mm (13 ga.)2.5 mm (12 ga.) Min. cutting radius250 mm30 mm Strokes per minute (min-1)4,3004,300 Overall length362 mm364 mm Net weight1.9 kg2.0 kg1.9 kg2.0 kg Rated voltageD.C. 14.4VD.C. 18VD.C. 14.4VD.C. 18V
  • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
  • Specifications and battery cartridge may differ from country to country.
  • Weight, with battery cartridge, according to EPTA-Procedure 01/2003

Symbols END004-6 The following show the symbols used for the equipment. Be sure that you understand their meaning before use.

instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

Read instruction manual.

Only for EU countries

Do not dispose of electric equipment or battery pack together with household waste material! In observance of the European Directives, on Waste Electric and Electronic Equipment and Batteries and Accumulators and Waste Batteries and Accumulators and their implementation in accordance with national laws, electric equipment and batteries and battery pack(s) that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

CORDLESS SHEAR SAFETY WARNINGS GEB067-1

1. Hold the tool firmly. 2. Secure the workpiece firmly. 3. Keep hands away from moving parts. 4. Edges and chips of the workpiece are sharp. Wear gloves. It is also recommended that you put on thickly bottomed shoes to prevent injury. 5. Do not put the tool on the chips of the workpiece. Otherwise it can cause damage and trouble on the tool. 6. Do not leave the tool running. Operate the tool only when hand-held. 7. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 8. Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. 9. Avoid cutting electrical wires. It can cause serious accident by electric shock.

Intended use ENE037-1 The tool is intended for cutting sheet steel and stainless sheet steel.

General Power Tool Safety Warnings GEA010-1

Cd Ni-MH Li-ion

Page 5 of the Makita DJS100 user manual — Switch action (Fig. 3)
Seite 5 · Zum Vergrößern klicken
Seite 5

SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

Installing or removing battery cartridge (Fig. 1)

IMPORTANT SAFETY INSTRUCTIONS ENC007-8

  • CAUTION:
  • Always switch off the tool before installing or removing of the battery cartridge.
  • Hold the tool and the battery cartridge firmly when installing or removing battery cartridge. Failure to hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a personal injury. To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 2. Do not disassemble battery cartridge. 3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. 4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 6. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F). 7. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 8. Be careful not to drop or strike battery. 9. Do not use a damaged battery. 10. Follow your local regulations relating to disposal of battery.

  • CAUTION:
  • Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
  • Do not install the battery cartridge forcibly. If the cartridge does not slide in easily, it is not being inserted correctly.

Battery protection system The tool is equipped with a battery protection system. This system automatically cuts off power to the motor to extend battery life. The tool will automatically stop during operation if the tool and/or battery are placed under one of the following conditions: • Overloaded:

The tool is operated in a manner that causes it to draw an abnormally high current. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart. If the tool does not start, the battery is overheated. In this situation, let the battery cool before turning the tool on again. • Low battery voltage:

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. 2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. 3. Charge the battery cartridge with room temperature at 10°C - 40°C (50°F - 104°F). Let a hot battery cartridge cool down before charging it. 4. Charge the battery cartridge once in every six months if you do not use it for a long period of time.

The remaining battery capacity is too low and the tool will not operate. In this situation, remove and recharge the battery.

Switch action (Fig. 3)

Page 6 of the Makita DJS100 user manual — ASSEMBLY
Seite 6 · Zum Vergrößern klicken
Seite 6

properly and returns to the “OFF” position when the rear of the switch lever is depressed. • Switch can be locked in “ON” position for ease of operator comfort during extend use. Apply caution when locking tool in “OFF” position and maintain firm grasp on tool. To start the tool, slide the switch lever toward the “I (ON)” position. For continuous operation, press the front of the switch lever to lock it. To stop the tool, press the rear of the switch lever, then slide it toward the “O (OFF)” position.

OPERATION

Lubrication (Fig. 8) Before operation, lubricate the contact point of the center blade and the pin. To keep good cutting performance, also use a cutting lubricant from time to time during operation.

OPERATION (Fig. 9) Turn the tool on and set front ends of the side blades on the workpiece. Now simply move the tool forward, keeping the side blades flush with the workpiece surface. (Fig. 10)

Indication lamp with multi function (Fig. 4) Indication lamps are located in two positions. - Battery cartridge replacing signal - When the battery power is almost used up during operation, the red lamp lights up and the tool stops immediately. Replace the battery with fully charged one when the red lamp lights up. - Accidental re-start preventive function - Even if the battery cartridge is inserted on the tool with the slide switch in the “I (ON)” position, the tool does not start. At this time, the lamp flickers slowly and this shows that the accidental re-start preventive function is at work. - To start the tool, first slide the slide switch toward the “O (OFF)” position and then slide it toward the “I (ON)” position.

MAINTENANCE

ASSEMBLY

Replacing carbon brushes (Fig. 11) Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Insert the top end of slotted bit screwdriver into the notch in the tool and remove the holder cap cover by lifting it up. (Fig. 12) Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. (Fig. 13) Reinstall the holder cap cover on the tool.

Adjusting the blade clearance For DJS160 and DJS161 only Adjust the clearance between the side blade and the center blade according to the thickness of the workpiece. (Fig. 5) First use a hex wrench to loosen the screw. (Fig. 6) Then use the hex wrench to adjust the clearance by tightening or loosening the bolt. There may be a slight difference between clearance of both sides of the center blade. Check the smaller clearance with the thickness gauge and adjust it. When using the thickness gauge to adjust the blade clearance, refer to the table.

Workpiece thickness (mm)Marking on thickness gauge Less than 0.80.5 0.8 - 1.31.0 More than 1.31.5

After adjusting the clearance, tighten the screw securely.

Storing hex wrench (Fig. 7) Store the hex wrench as shown in the figure when not in use.

Page 7 of the Makita DJS100 user manual — OPTIONAL ACCESSORIES
Seite 7 · Zum Vergrößern klicken
Seite 7

For DJS160 and DJS161

Vibration ENG900-1 The vibration total value (tri-axial vector sum) determined according to EN60745:

MaterialCutting thickness (mm)Life of blades (m) Mild steel plate (SPCC)1.6200 Stainless steel plate (SUS304)1.2150 Aluminum plate (A-5052)2.5400
Model DJS100 Work modecutting sheet metal Vibration emission (a h ): 12.5 m/s 2
Uncertainty (K)1.5 m/s 2
Model DJS101, DJS161 Work modecutting sheet metal Vibration emission (a h ): 13.0 m/s 2
Uncertainty (K)1.5 m/s 2
Model DJS160 Work modecutting sheet metal Vibration emission (a h ): 12.0 m/s 2

For DJS100 and DJS101

MaterialCutting thickness (mm)Life of blades (m) Mild steel plate (SPCC)1.0120 Stainless steel plate (SUS304)0.750
Uncertainty (K)1.5 m/s 2
  • ENG901-1
  • The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another.
  • The declared vibration emission value may also be used in a preliminary assessment of exposure.
  • WARNING:
  • The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used.
  • Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

  • CAUTION:
  • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
  • Thickness gauge
  • Center blade
  • Side blade R
  • Side blade L
  • Hex wrench
  • Makita genuine battery and charger

For European countries only ENH101-16 EC Declaration of Conformity We Makita Corporation as the responsible manufacturer declare that the following Makita machine(s): Designation of Machine: Cordless Metal Shear Model No./ Type: DJS100, DJS101, DJS160, DJS161 are of series production and Conforms to the following European Directives:

2006/42/EC And are manufactured in accordance with the following standards or standardised documents:

EN60745 The technical documentation is kept by:

Makita International Europe Ltd. Technical Department, Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, England

Model DJS100, DJS101, DJS161 Sound pressure level (LpA): 71 dB (A) Uncertainty (K): 3 dB (A) The noise level under working may exceed 80 dB (A).

31. 7. 2009

Model DJS160 Sound pressure level (LpA): 74 dB (A) Uncertainty (K): 3 dB (A) The noise level under working may exceed 80 dB (A).

Director Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi, 446-8502, JAPAN

Wear ear protection.

Tomoyasu Kato

Frage zu Makita DJS100 stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Makita DJS100

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Makita DJS100 PDF-Anleitung

48 Seiten·1.1 MB·Sonstiges·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…