Benutzeranleitung / Produktwartung MTD7122B09 des Produzenten Bolens
Zur Seite of 40
STOCK NUMBER 93-7122.0 MODEl. NUMBER MTO1122B09 FACTORY NUMBER 130..61OF098 Thank you tol' purchasing an Amel'lcan-built product..
.3 .5 .6 10 Slope Gauge Safe Operation Practices Assembly Instructions. . Controls.. " Operation. Adjustments lubrication Maintenance Off-Season Storage. 19-23 ,.. .24.25 26-33 ..., ...29 34,35 36-39 Back Cover 12 14 15 18 Engine Operating and Maintenance Instructions.
i > I ..J I W , u. c:( U') I W I ..- I c:( I a: I w I Q. 10 I ..- 10 : Z I > I « I ~ I I => 10 I > I UJ I a: I UJ I :I: ~ :s: 41 .S U') -J W .~ Q. oC 0 ~-.. ..J cn c:t W -Z :J - Y ~ I a: I w I t- I UJ I C 10 I ..- I I W I C I - I => I " I « I cn I « I I .
I I I Remove this sheet from your owner's manual and lay the hardware on the illustration for identification purposes. After assembly, keep the Slope Gauge which is on the reverse side of this sheet for future use. (Hardware pack may contain extra items which are not used on your unit.
RULES FOR SAFE OPERA liON THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWEO COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERlY OF YOURSELF AND OTHERS READ AND FOLLOW ALL INST.
ASSEMBLY IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL; however, a small amount of oil may be present from the factory. Do not overfill. After assembly, service engine with gasoline and oil as instructed in the engine section of this manual.
Caps " ~ FIGURE 1, ,f. FIGURE 2. ACTIVATING THE BATTERY Do not activate battery (fill with battery acid) until battery is actually placed in service. Be certain to read previous warnings before activating the battery. 1. Open the battery pack. Be careful not to puncture the box.
Negative I~ ,I =~~~ ..! r- --.,,- / Positive y Terminal Battery ~ Drain Tube '9 ~ -'- -- Battery - Black Box Red (Negative) (Positive) Cable Cable INSTALLING THE BATTERY (Hardware A) 1.
Steeri ~ ~~HeX Lock Wheel ,~ Nut , ..,r" :--- Cupped Washer 3. Attach one end of steering bellow to the steering wheel as shown in figure 6, inset. 4. Position the front wheels of the tractor so they are pointing straight forward. 5. Place the steering wheel and steering bellow over the steering shaft.
CONTROLS LIGHT SWITCH Push the light switch to turn on the lights. The lights will only operate when the engine is running. See figure 9. AMMETER The ammeter registers the rate of battery charge or discharge. The ammeter will register on the discharg- ing side when starting the engine.
INTERLOCKS (Not Shown) Interlock safety switches are located by the clutch-brake pedal. the li"t lever, the gear shift lever and under the seat. Before the engine will start, the clutch-brake pedal must be (jepressed all the way and the lift lever must be in the disengaged position.
WARNING: Look to the rear before back- ing up. Move the lift lever into the DISENGAGED position to raise the deck and disengage the blades. GRASS CATCHER Stock Number 95-1136-1 (Factory No. 190-064) is available as optional equipment. A WARNING: The mower should not be operated without the entire grass catcher or chute deflector in place.
SPEED CONTROL ADJUSTMENT (See figure 12) NOTE: When operating the unit initially or after replac- ing the belt5. there will be little difference between the highest two speeds until after the belts have gone through a break-in period and have seated themselves into the pull~ys.
FIGURE 15. BRAKE ADJUSTMENT (See figure 16) The brake is located by the right rear whee! inside the frame. During normal operation of this machine, the brake is subject to wear and will require periodic examination and adjustment. WARNING: Do not have the engine running when you adjust the brake.
STEERING SHAFT Lubricate steering shaft at least once a season with light oil. ENGINE Refer to the engine section of Iris manual for all engine maintenance instructions. CLEANING ENGINE AND BLADE HOUSING Any fuel or 011 spilled on the machine should be wiped off promptly.
Blade Mounting Torque 3/8" Dia. Bolt 375 in. Ib, min.. 450 in. Ib, max. 5/16" Dia. Bolt 150 in. Ib, min., 250 in, Ib, max, To insure safe operation of your unit, ALL nuts and bolts must be checked periodically for correct tightness. FUEL FILTER Your unit is equipped with a replaceable in-line fuel filter.
6. Remove the engine pulley belt guard by slipping it back and to the right. See figure 23. 3 Push the idler pulley toward the right side of the unit. Lift the belt over the idler pulley. See figure 21 . 4 Remo'e the belt from the variable speed pulley.
BATTERY REMOVAL OR INSTALlATION A WARNING: When removing the battery, follow this order of disassembly to prevent the screwdriver from shorting against the frame. COMMON CAUSES FOR BATTERY FAILURE ARE: 1. Overcharging 2. Undercharging 3. Lack of water 4.
FOR ENGINE MODEL 281707-0411-01 IMPORT ANT: Do not start the engine before reading the following section of this manual. A WARNING: Do not operate engine in an enclosed area.
SECTION 2 STARTING A WARNING: ALWAYS KEEP HANDS AND FEET CLEAR OF MOWER BLADE OR OTHER ROTATING PARTS. Lift )) ~ "' ~ ", -, -- '. ~~ ~ -.,' ~~:- ,~- .~ ':(~::~l~~~'~~': -'-- Throttle Clutch- Brake Pedal' /" To Start Engine 1.
2 Remove foam pre-cleaner. Spark Plug-Clean and reset gap at .030" every 1 00 a. Wash pre-cleaner in liquid detergent and warm hours of operation. water to remove dirt. NOTE: Do not blast clean spark plug. Spack plug b. WrElp pre-cleaner in cloth and squeeze dry.
J - ~~~:;qll~~~ ~- ~ ~ ~ °!8-C~'ok~ . Casing Clamp Screw Now open needle valve 1-1/2 turns counterclockwise and idle valve one turn. This initial adjustment will per- mit the engine to be started and warmed up approx- imately 5 minutes prior to final adjustment.
b. While engine is s1ill warm, drain oil from crankcase Refill with fresh oil, c. Remove spark plug, pour approximately '/2 ounce (15 cc) of engine oil into cylinder and crank slowly to distribute oil. Replace spark plug. d. Clean dirt and chaff from cylinder, cylinder head fins, blower housing, static guard and muffler areas.
TROUBLE SHOOTING CHART FOR ELECTRIC START MODELS -REMEDY- ---:J The battery must be instatled with the negative terminal, identified at t'le terminal post by (Neg.
ILLUSTRATED PARTS FOR MODEL MT[)7122BO9 LAWN TRACTOR , PARTS LIST FOR MODEL MTD7122BO9 LAWN TRACTOR I REF. -+-~ PART NO. DESCRIPTION DESCRIPTION 1 ~T-Pm- ~~j NO.
..r 1 1.2 ./ . 17 ~ L;, " " " :) 6 I. ~ ,~ 21. '. ~'5 ~ ~ ~~8 '" ~ 6$ 41 , 11-;-(( 15-i ~ ' 1.Q . 5 .. 6 w/ 17 /1 " ~ 36,~ '~'..~' -~ '- ~.. . ~~:;~ .,' -.~ ~.~. 31 I r'-- 35 z: .
Il.LUSTRATED PARTS FOR MODEL MTD7122BO9 LAWN TRACTOR ""':~ 5' ~t 7-- 61 ~-'y--w "'~i ~"':~~. ;--8 -..r ~ 9 j , / ;; ~ 33 / " """" 44 / ,10 ---QI 55 ' :.-~-:-~ ~ 58,' ,'26 t ~;;--o:;;;~~~>.
.
rAEFT- PART--- ~-:-i !!:.O-.:.-- --- : 1 i 731-0220 2 712-0237 3 736-0242 I 4 i 731-0805 I 51731-0954 , 6'16512 I 71741-0356 I 8 1712-0324 9117198 I 10 1738-0141 11 ;710-0152 :..-:- ClutC~VeIIOW- -.-Red--o.:c:--- 13 ~T 14 - : S r='"-- tart: -==-.
ILLUSTRATED PARTS FOR MODEL MTD7122BO9 LAWN TRACTOR ~ 114 ~ 91 . ~ -~ < : ..oJ ~ ~ , ~_-" c' -~ "'- ., -"""~ rr -~~ .:: 2 9 ,E;I ~. 8- 1 ~"--'.~: 97 !of , ...j' '1 i 'I;' '389.: '85"'~;!J~- 18 B8 ~__~~b~/"A .
I RE"FT-pART- ~~_t:l~- 1 1 12 H.P. 2,710-0726 I 31725-0977 4 712-0123 5 736-0119 7i 736-0247 9 ! 750-0777 10 710-1077 PARTS LIST FOR MODEL MTD7122BO9 LAWN TRACTOR ~ , DESCRIPTION I REF" PART ! NO. NO. , c--- ~-r ' , Engine (See Breakdown)! 621 711-0768 , Hex Wash, AB-Tap Scr, 5/16" x I 63i 736-0275 .
~ 1--""'" PARTS LIST FOR MODEL MTD7122BO9 LAWN TRACTOR REF I NO.'r PART NO. REF. I NO. PART NO. DESCRIPTION DE~CRIPTION.I 1 I 09735A 2 17640 3 17641 4 17710 5 14800 6 14804 7 .
Ill.USTRATED PARTS FOR MODEL MTD7122B,O9 LAWN TRACTOR 53" PARTS LIST FOR MODEL MTD7122BAO9 LAWN TRACTOR REF. PART -DESCRIPTION ~EF. PART -;;;;;;~I~~ NO. NO. .NO. NO. - ~ - 1 750-0776 Spacer .33" 1.0. x .88" 20 736-0217 I L-Wash. 3/8" I.
ILLUSTRA TED P ARTS FOR MODEL MTD7122BO9 LAWN TRACTOR 52d LJ I 22 232' 22 ~ ,yV 2'- -- ~ -,_.' -f rI-. 8 -- 45, e I '. "2S "26 "" ~, 17 ,~ I 28 '6 IS ""'~ ' 30 '0 I 20 ! 1 21 " tcI-18 37 '/ ~ { 23 ,~ 56 .
!REFT ~ REF .- I No.1 --- 1 ; 714-0129 2 ' 1 716-0115 i 3 71 0-0854 I 4,710-0809 I 5: 717-0540 i 6 1710-0642! 7 1712-0287 I 8 1717-0634 9/721-0178 10 1736-0335 PART NO. PARTS LIST FOR MODEL MTD7122BO9 LAWN TRACTOR ---, ---m ' -, ~~,,"",-~~~~ON- ---i ~J P:~.
.
ILLUSTRATED PARTS FOR 281707-0411-01 ENGINE FOR MODEL MTD7122B09 LAWN TRACTOR ;l4K::::-: --!f ~ ,-- --" ) E , 224 ~ J09 ~ 1- ~ousin9 l~nglh-f 310 <»~L- I -~ j 544 0 ~ 803 , I ~ 37 ~) t8332 ~S '~~~I 801 NOTE: To identily Briggs & Stratton manulactured starter rnotors.
PARTS LIST FOR 281707-0411-01 ENGINE FOR MODEL MTD7122BO9 LAWN TRACTOR .--,-- PART NO. DESCRIPTION DESCRIPTION -~ - 1 2 3 5 7 8 9 10 11 12 45 46 52 78 94 95 98 91920 *271996 99 101 104 108 118 121 123.
PARTS LIST FOR 281707-0411-01 ENGINE FOR MODEL MTD7122BO9 LAWN TRACTOR (CONTINUED) ' '-' --- REF. i PART ~-- --~--~." NO. NO. -+ 634~ ~- i REF.
HOW AND WHERE TO ORDER REPLACEMENT PARTS To eliminate error and to speed delivery of replacement parts, always include the following information on your order. 2. Best possible identification of the part itself (a) Part Number- (b) Part Name- (c) If necessary return the old part as sample.
Ein wichtiger Punkt beim Kauf des Geräts Bolens MTD7122B09 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Bolens MTD7122B09 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Bolens MTD7122B09 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Bolens MTD7122B09 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Bolens MTD7122B09 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Bolens MTD7122B09 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Bolens MTD7122B09 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Bolens MTD7122B09. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Bolens MTD7122B09 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
