
Jamo C 80














Welcome to the exclusive circle of Jamo C 80 owners! This manual will give you a quick overview of how to set up your speakers in your room. For more in-depth information about the technologies used please refer to the C 80 technical descrip- tion and www.Jamo.com
First, a word of advice. After setting up your speakers for the fi rst time, please allow at least a couple of days before you start fi ne-tuning the sound. This will serve two purposes. Firstly, you will get a sense of what these speakers sound like. Secondly, it will give time for the speakers to run in: the tonal quality of this design changes slightly after the fi rst couple days of playing music.
Please remember the guidelines in this manual are only recommendations. There are no hard and fast rules about setting up a pair of speakers. When you get down to fi ne-tuning their performance in your room don’t be afraid of experimenting: any speaker will sound different when moved a few inches. Feel free to change the speaker positions and move them around the room to determine your best listen- ing position and sound.
Always rely on your own judgement to determine what sounds best. We do...
Enjoy!

Stereo triangle You can use the stereo triangle as a good rule of thumb when placing your speak- ers. This means the distance between the speakers should be the same as the dis- tance from your listening position to both speakers; in other words an equilateral triangle.

Damping If your room…
a) doesn’t allow you to get the speakers the required distance from the back and side walls or…
b) has highly refl ective surfaces (i.e. glass windows or bare plastered walls) or…
c) still doesn’t sound quite right
…we strongly recommend that you ‘damp’ your room’s critical surfaces. This can be done simply by adding curtains, furniture, bookshelves and so on. A damped surface is almost always preferable to a hard refl ective surface.
Depending on the placement of the speakers, room size, sound refl ecting surfaces, furniture, etc, it is entirely up to you how you fi ne-adjust the placement, angling and damping. Remember to take your time and use your ears.

Toe-in To achieve optimal sound, try experimenting with ‘toeing in’ the speakers towards the listening position. This achieves two things:
a) Fine-tuning of the tweeter level, which is more sensitive to refl ections than mid- range and bass output, treble is more directive than midrange and bass frequencies.
b) Secondly you minimize side-wall refl ections, thereby reducing colouration of the sound.
Some may not feel a need to toe in the speakers at all, while others may fi nd the best solution is to point them directly at the listening position. See what suits you best…


The C 803, C 805, C 807 and C 809 speakers comes prepared for bi-wiring. Please note the following three possible setups.
Single-wiring For single-wire connections, the terminal jumpers should be attached as shown in the illustration.

Bi-wiring If you’d like to use a bi-wiring arrangement, make sure you remove both the termi- nal jumpers before you connect up your loudspeaker cables like so…

Bi-amping In a bi-amped system, make sure you remove both the terminal jumpers before connecting up your cables as shown. If you choose this option, we recommend you use identical amplifi ers to drive both the bass and treble units.


After the initial placement of the C 80 fl oorstanders, you might consider using the supplied spikes instead of the built-in rubber feet. To fi x them on, we recommend that you gently lay the speaker on one side and screw in all four spikes together. Before you do this, however, be sure to place a couple of thick towels or similar underneath the side of the speaker. This will prevent accidental scratching to the surface of the speaker.

After screwing in the spikes, gently bring the speaker to its vertical position. Once upright simply adjust the spikes to give optimal support.
Using the spikes will give the very best support and sound quality. If you want to spare your fl oor surface from being punctured however, you can place the indent- ed metal washers underneath the spike.
A warning: be careful when using the spikes with the indented metal washers – you don’t want to get your fi nger trapped between the two!
Whichever option you choose, avoid “walking” the speakers if you need to move them to a different position… especially on hard wood fl oors!

Placement For an optimal listening experience, we recommend you place these speakers a minimum of 2m/6ft from each other, a minimum of 0.5m/1.5ft from the back wall and at least 1m/3ft from any side walls.


Placement For an optimal listening experience, we recommend you place the C 80 CEN close to your screen, either just above or just below it. The speaker is magnetically shield- ed so it can be placed close to a normal CRT-type TV.
Make sure the C 80 CEN stand/cradle is as stable as possible to ensure the optimal sound from the C 80 CEN.
Angling To achieve optimal sound, the included speaker cradle is constructed in such a way that you can angle the C 80 CEN directly towards your listening position. Try experi- menting with different angles until you are fully satisfi ed.




Placement The C 80 SUR are best placed at a 20 degree angle from the listening position and at a height of approximately 2m/6ft.


6.1 and 7.1 setup If you want to have a 6.1 surround setup, we recommend using an additional C 80 SUR (left) speaker. Place it right between the two side walls just behind your listen- ing area, to achieve optimal sound.

In a 7.1 setup, use a pair of C 80 SUR and place them 1/4 of the full room width from each sidewall. Note: when placing the C 80 SUR as surround back speakers, you must place the C 80 SUR (left) on the right side of the room, and vice versa for the other speaker, in order to achieve correct dispersion from the dipole speakers.


If you go to www.Jamo.com or look at the CD-rom which came with the product, you can fi nd a couple of useful subwoofer test signals. These will help you to set up your subwoofer so it delivers the maximum performance. Burn the test signals onto a CD and put them in your CD/DVD player.
Placement rules for subwoofers When placing a subwoofer in a room, you have more freedom than you would with an ordinary speaker because a sub generates less-directional low frequencies, which make it harder for the human ear to determine the direction they are com- ing from. We do still recommend, however, that you place the C 80 SUB mid-way between the two front speakers if possible. This is because: A). The C 80 SUB will be easier to align, both level- and phase-wise, with the speak- ers. B). Even though low frequencies are less-directional, higher frequencies can make the subwoofer easier to pinpoint sonically.
If it isn’t possible to place the C 80 SUB between the two front speakers, the ad- vanced electronics provided in the subwoofer still makes an easy and seamless in- tegration possible.
Three different placement positions - sound refl ections and amplifi cation There are basically three different ways to place a subwoofer, either of which will affect the overall sound level. A). Placing it away from any wall will give the lowest sound level, but typically the most linear frequency response. B). Placing it next to a wall will increase the low frequency level. C). If it is positioned up against two walls, i.e. in a corner, the subwoofer will - be- cause of wall refl ections - accentuate the low frequencies even more.


Finding the right place for your subwoofer Irrespective of the location you choose for the subwoofer, it is essential to have as linear a frequency response as possible. There should, in other words, be as few dips and peaks in the response as possible. When evaluating the best location for the subwoofer, listen to some music or test tones from your favourite listening position, then try to move the subwoofer around the room to fi nd the location that best suits your personal preference.
Line/LFE input terminals If your preamp/amplifi er has a subwoofer out or subwoofer LFE out, please connect it to the LFE input terminal on the C 80 SUB. If you have an additional subwoofer, it is possible to connect it via the C 80 SUB’s LFE output terminal.


If you don’t have a subwoofer out, you can connect the amplifi er’s speaker output directly to the speaker-level input terminals on the C 80 SUB. Remember to connect both the left and right speaker outputs from the amplifi er to the left and right input if you have just the one subwoofer connected. If only one channel is hooked up, the C 80 SUB will only reproduce the low frequencies contained in that channel.
Always remember to connect ”+” and ”-” from the amplifi er to the corresponding ”+” and ”-” terminals on the subwoofer speaker level input.


Level The level control on the C 80 SUB controls the volume.

Phase When all the speakers in your system and the subwoofer have been connected it is very important you have them connected in phase.
It is easier to adjust the phase on the subwoofer if you have someone helping you. Sit in the listening area and ask your helper to turn the phase control while you’re playing back bass-heavy music or the test frequency fi les found at www.Jamo.com or on the CD-rom which came with the product. Turn the control back and forth to determine the position where the overall bass level sounds the loudest; that’s when you’ll know the subwoofer is in correct phase.


Cut-off frequency If the C 80 SUB is connected via an unfi ltered output signal, such as a line pre-out or speaker output, it is necessary to adjust the cut-off frequency on the subwoofer to match the bass response of your speakers. If it is connected via a fi ltered output signal, such as a LFE or ‘subwoofer out’, the cut-off frequency should be turned all the way up, in order to stop the C 80 SUBs cut-off fi lter interfering with the fi lter built into your decoder/AV receiver.

Auto/On/Off The Auto/on/off switch offers three settings: Auto: The Subwoofer will automatically switch on when it detects a signal from
the source, and switch into stand-by mode again 20 minutes after the signal has terminated. On: The subwoofer will stay on Off: The subwoofer will stay in stand-by mode


Variable Boundary Gain Compensation Variable Boundary Gain Compensation is a fi lter which can compensate for bass peaking which typically starts around 60Hz and increases downwards. At fi rst, this effect sounds superfi cially impressive, but listen to music for any length of time and it becomes “boomy” and rather annoying. The effect commonly occurs in smaller rooms and when your listening position is near to a wall, hence the name Boundary Gain Compensation. As with phase adjustment, we recommend you play music or the test frequency fi les from www.Jamo.com and have a friend turn the Variable Boundary Gain Compensation control, while you sit in the listening area. Then simply adjust it so that when the bass hits the lowest frequencies, there aren’t any detectable bass peaks.

Please use a dust-free cloth to clean the speakers. It is also possible to use a slightly damp cloth for more stubborn marks. Under no circumstances should you use any kind of cleaning agent on, or in close proximity to, these speakers.


Name C 809 System 3 way bassrefl ex Woofer (In / mm) 2 x 7 / 180 Midrange (In / mm) 7 / 180 Tweeter (In / mm) 1 / 25 Long term power (W) 200 Short term power (W) 400 Sensitivity (dB/2,8V/1 m) 89 Frequency range (Hz) 30-24000 Impedance (Ohm) 6 Crossover frequency (Hz) 150 / 2000 Dimensions HxWxD In 45.6 x 9.9 x 16.9 Mm 1157 x 252 x 428
Name C 80 CEN System 2 way bassrefl ex Woofer (In / mm) 2 x 6 /155 Midrange (In / mm) - Tweeter (In / mm) 1 / 25 Long term power (W) 160 Short term power (W) 320 Sensitivity (dB/2,8V/1 m) 88 Frequency range (Hz) 80-24000 Impedance (Ohm) 6 Crossover frequency (Hz) 2000 Dimensions HxWxD In 8.3 x 8.9 x 13.4 Mm 212 x 501 x 281
Name C 807 System 2½ way bassrefl ex Woofer (In / mm) 7 / 180 Midrange (In / mm) 7 / 180 Tweeter (In / mm) 1 / 25 Long term power (W) 180 Short term power (W) 360 Sensitivity (dB/2,8V/1 m) 89 Frequency range (Hz) 35-24000 Impedance (Ohm) 6 Crossover frequency (Hz) 150 / 2000 Dimensions HxWxD In 39.6 x 9.6 x 16.0 Mm 1007 x 242 x 406
Name C 80 SUR System 2 way dipole Woofer (In / mm) 2 x 6 / 155 Midrange (In / mm) - Tweeter (In / mm) 2 x 1 / 25 Long term power (W) 160 Short term power (W) 320 Sensitivity (dB/2,8V/1 m) 87 Frequency range (Hz) 80-24000 Impedance (Ohm) 6 Crossover frequency (Hz) 2500 Dimensions HxWxD In 11.5 x 11.3 x 7.1 Mm 293 x 286 x 181
Name C 805 System 2½ way bassrefl ex Woofer (In / mm) 6 / 155 Midrange (In / mm) 6 / 155 Tweeter (In / mm) 1 / 25 Long term power (W) 160 Short term power (W) 320 Sensitivity (dB/2,8V/1 m) 88 Frequency range (Hz) 40-24000 Impedance (Ohm) 6 Crossover frequency (Hz) 150 / 2000 Dimensions HxWxD In 34.5 x 7.9 x 13.7 Mm 877 x 201 x 347
Name C 80 SUB System Closed box Woofer (In / mm) 2 x 10 / 254 Amplifi er rated output (W) 1800 Frequency range (Hz) 20 – 200Hz Cut off frequency (Hz) Variable Impedance (Ohm) 22k Phase Variable Boundary Gain Comp Variable Limiter Yes Auto/on/off switch Yes 12V trigger Yes Motional Feedback Yes Dimensions HxWxD In 17.6 x 15.4 x 17.0 Mm 447 x 390 x 432
Name C 803 System 2 way bassrefl ex Woofer (In / mm) 7 / 180 Midrange (In / mm) - Tweeter (In / mm) 1 / 25 Long term power (W) 125 Short term power (W) 250 Sensitivity (dB/2,8V/1 m) 87 Frequency range (Hz) 45-24000 Impedance (Ohm) 6 Crossover frequency (Hz) 2000 Dimensions HxWxD In 15.0 x 8.9 x 13.4 Mm 380 x 225 x 341

English

The lightning fl ash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi cient magni- tude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature ac-companying the product.
The scope of the warranty
Service. In case of warranty enquiries, please contact your dealer/ installer. In case of request for service under warranty, please enclose your original receipt and make sure that the serial number on the product is readable. Important: Never send the product to be repaired without the prior agreement of your dealer. If the product is STILL UNDER WARRANTY, Jamo will pay freight costs back and forth between the dealer and the Jamo authorised service centre. Any other freight must be paid for by the customer. The product must always be packed properly. If the product is NOT UNDER WARRANTY, all costs including without limit costs of repair and freight must be paid for by the customer.
Warranty certifi cate. Jamo provides a sixty (60) month warranty from the date of purchase against material and manufacturing defects on passive speakers and a twenty-four (24) month warranty on electronics; in the US only, Jamo provides a limited lifetime warranty on in-wall and in-ceiling speakers (each, a warranty period). For defects covered by the warranty, the product must be returned to the dealer/installer that sold the product.
Nothing in this warranty shall limit your statutory rights.
The warranty is only valid on presentation of the original sales receipt or other valid proof of purchase, and provided that the serial number on the product is fully legible.
Warranty repairs must be carried out by an authorised Jamo dealer, or an authorised service centre. No payment will be made for repairs performed by unauthorised persons. This warranty does not extend to products which have been repaired or otherwise altered by unauthorised persons, and any damage to the product caused by work by unauthorised persons is not covered by this warranty.
This product will not be considered defective, either in materials or in manufacture, to the extent that faults are caused by adaptation to national, local, technical or safety related requirements in countries other than the specifi c country where the product was purchased.
Jamo shall at its option during the relevant warranty period either repair or replace defective components. If the component repair or replacement cannot be performed, the product will be replaced.
In no circumstances shall Jamo be liable in contract, tort (including negligence) or breach of statutory duty or otherwise for loss of profi ts, loss of revenue, loss of data, loss of business or loss of anticipated savings or for any consequential loss whatever.
The warranty does not cover the following: a) Periodic inspection, maintenance and repair or replacement of parts resulting from normal wear and tear. b) Costs connected to delivery to the dealer, disassembly or re-installation of the product. c) Misuse, including use for purposes other than was intended, or faulty installation. d) Damage caused by lightning, water, fi re, natural catastrophes, war, insurrection, incorrect line voltage, insuffi cient ventilation, transport or other causes outside of the control of Jamo.
This warranty applies to every legal owner of the product during the warranty period.

Use only with the cart, stand, tripod, bracket, or table specifi ed by the manu- facturer, or sold with the apparatus. When a cart is used use caution when moving the cart / apparatus combination to avoid injury from tip-over.
Terms of Warranty


In dieser Anleitung genannte Seiten – Hersteller, Support und Downloads.
Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.
Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.