Benutzeranleitung / Produktwartung WFPE-30F des Produzenten Bloomfield
Zur Seite of 22
IMPORTAN T : DO NOT DISCARD THIS MANUAL This manual is considered to be part of the FR YER and is to be given to the OWNER or MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of the FRYER. Additional manuals are available from your WELLS DEALER .
All commercial cooking equipment manufactured by WELLS MF G . CO. is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory, which- ever comes first, and is for the benefit of the origi- nal purchaser only .
TABLE OF CONTENTS GENERAL SPECIFICATIONS 1 Specifications 1 Features and Operating Controls 2 Safety Procedures 4 Installation Instructions 5 Operating instruction 10 Maintenance Instructions Filter Paper Installation 1 1 Filtering Oil 12 Discarding Used Oil 14 Cleaning the Fryer 15 Troubleshooting 17 Service Parts List 19 DIMENSIONS Wide 15.
2 1. POWER SWITCH FRYER position turns ON the FR YER and POWER LIGHT ; and, ( FRYER-OFF-FILTER ) turns OFF the FIL TER PUMP . Heating elements are energized and regulate to the temp. set on the CONTROL THERMOST A T ( item 8) . OFF position turns OFF the FRYER and de-energizes the lower panel FILTER PUMP SWITCH (item 6).
3 7. HI-LIMIT THERMOSTAT Provides over-temperature protection by de-energizing the HEATING ELEMENTS if the oil temperature exceeds the factory-set limit. RESET must be performed manually. Allow the oil to cool below 300ºF (93ºC), then firmly press the red button on the LOWER CONTROL PANEL until it resets (snaps).
4 SAFETY PROCEDURES Knowledge of proper procedures is essential to the safe operation of electrically energized equipment. In accordance with generally accepted product safety labeling guidelines for potential hazards, the following signal words and symbols are used throughout this manual.
INS TALLATION INSTRUCTIONS 5 A. UNPACKING AND INSPECTION 1. Carefully remove the FRYER from the carton. Remove all protective plastic film, packaging materials and accessories from the FR YER and the FIL TER RESER VOIR before connecting electrical power to the FR YER or otherwise performing any installation procedures.
D. ELECTRICAL INST ALLA TION 1. Refer to the nameplate on the front of the fryer. Verify the ELECTRICAL SERVICE POWER. Voltage and phase must match the nameplate specifications, and available electrical service amperage must meet or exceed the specifications listed on page 1.
7 E. EQUIPMENT PREPARATION PRIOR TO OPERATION 1. CLEANING: Prior to leaving the factory, the fryer is tested for proper operation with peanut oil. After testing is complete, the oil is removed but oil residue remains. Therefore, it is necessary to clean the frypot before filling it with fresh oil.
3. Install the SUCTION TUBE O-RIN G , FILTER SCREEN, FILTER PAPER and FILTER PAPER HOLDER into the FILTER RESERVOIR. Install the assembled FILTER RESERVOIR into the fryer.
7. DETERMINE MAXIMUM LOAD WEIGHT : For operational safet y, it is very important to determine the maximum load weight for the specific operation. This can be accomplished by starting out with small lo.
OPER AT ING INSTRUCTIONS 1 0 A . PRE-HEATING THE FRYER 1. Make sure the BASKET RACK (item 19) is in place, straddling the HE ATING ELEMEN T , and that the FR YPOT is filled with cooking oil to the proper level. 2. Open the door and set the THERMOS TAT (item 8) to the desired cooking temperature.
1 1 MAINTENANCE INSTRUCTIONS A. FI LT ER PAPER INS TALLATION Replace FIL TER P APER after each day ’ s filtration, or as needed to return oil promptly to the kettle. 1. Open the FRYER DOOR and slide the FILTER RESERVOIR forward to remove it. 2. Remove the FILTER PAPER HOLDER, used FILTER PAPER and FILTER SCREEN.
1 2 B. FI LT ERING OIL IMPORTAN T : Filtering the cooking oil helps to ensure the quality of the food product. Careful observation of the finished food product will help you determine your optimal filtering frequenc y . (Example: filter the oil after each six loads of fresh breaded product.
1 3 BURN HAZARD PROTECTIVE CLOTHING AND INSULA TED GLOVES MUST BE WORN WHEN CLEANING THE KETTLE WITH THE HI-TEMP BRUSH AND WHEN UNCLOGGING THE DRAIN WITH THE WOOD CLEANOUT DOWEL. The kettle will be hot and hot oil may splatter. Serious injury may result.
1 4 D. DISCARDING USED OIL IMPOR TANT NOTE: The following instructions for discarding used oil from the fryer may be disregarded if you use a WELLS MOBILE CADDY WAOC-1 (part no.
1 5 E. CLEANING THE FRYER SLIPPING & FALLING HAZARD / SPILLED OIL DO NOT ST ORE OIL IN THE FIL TER RESER VOIR WHILE CLEANING THE KETTLE. IF CLEANING FLUID IS ACCIDENT ALL Y DRAINED INT O THE FIL TER RESER VOIR, OIL WILL SPILL ON THE FLOOR.
7. With the POWER SWITCH in the OFF position, drain the cleaning solution. NOTE : Allow the solution to cool to 120ºF (49ºC) or less for safe handling. Using a suitable METAL container, drain the cleaning solution until the container is no more than one-half full.
TROUBLESHOOTING A. PROBLEM: FRYER WILL NOT HEAT 1. If: POWER LIGHT (item 2 ) NOT ON . Check the SERVICE POWER BREAKER. Reset if TRIPPED . If breaker continues to trip, contact a licensed electrician to repair field wiring (if that is the cause), or contact a Wells Mfg.
C. PROBLEM: FILTER PUMP WILL NOT RUN 1. Verify that the POWER SWITCH (item 1, upper control panel) is in the FILTER position, and that the FILTER PUMP SWITCH (item 6, lower control panel) is in the ON position. 2. Press the red RESET button (item 9) on the FILTER PUMP MOTOR, accessible on the back of the fryer.
SERVICE PARTS LIST IMPOR TANT: Use only factory authorized service parts and replacement filters. For factory authorized service, or to order factory authorized replacement parts, contact your WELLS AUTHORIZED SER VICE AGENCY , or call: Wells Manufacturing Company 2 Erik Circle, P .
WELLS MANUFACTURING COMPANY 2 ERIK CIRCLE, P . O. Box 280 Verdi, NV 89439 Customer Service (775) 345-0444 Ext. 502 fax: (775) 345-0569 www.wellsbloomfield.
Ein wichtiger Punkt beim Kauf des Geräts Bloomfield WFPE-30F (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Bloomfield WFPE-30F noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Bloomfield WFPE-30F - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Bloomfield WFPE-30F reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Bloomfield WFPE-30F erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Bloomfield WFPE-30F besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Bloomfield WFPE-30F verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Bloomfield WFPE-30F. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Bloomfield WFPE-30F gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
