Benutzeranleitung / Produktwartung 2030 des Produzenten Bloomfield
Zur Seite of 26
PRINTED IN UNITED STATES OF A MERIC A p/n 73902 Rev. F ECN- 12817 M653 05 0208 cps 653 OWNERS MANUAL for E-Max™ TEA BREWERS MOD EL S 2030 Includes: Installation Operation Use & Care Servicing Instructions Mode l 2030 Tea Brewer with optional 8799 Dispenser E-Max BREWERS are cov ered under U.
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged b y skilled personnel before le aving the factory. Upon acceptance of this shipm ent, the transportation company assumes full responsibility for its safe delivery.
TABLE OF CONTENTS SPECIFICATIONS Thank You for purc hasing this Bloomfield Industries appliance. Proper installation, professional operation and consistent maintenance of this appliance w ill ensure that it gives you the very best performance and a long, economical service life.
FE AT U R E S AN D O P E R AT I N G CO N T R OL S 2 Features & Operating Contro ls.
WARNING: Electric Shock Hazard All servicing requiring access to non-insu lated components must be performed by qualified service personnel. Do not open any access panels wh ich require the use of tools. Failure to heed this warning can re su lt in electrical shock.
INSTALLATION INSTRUCTIONS RE A D THIS CAREFULL Y BEFORE ST A RTING THE INST AL L A TION UNPACKING & INITIAL INSPECTION 1. Unpack the unit. Inspec t all components for c ompleteness and condition. Ensure that all pack ing materials have been rem oved from the unit.
INSTALLATION INSTRUCTIONS (continued) NOTE: This equipment must be installed to comply with applicable federal, state an d local plum bing codes an d ordinanc es. WARNING ELECTRIC SHOCK HAZARD: Brewer must be properly grounded to prevent possible shock hazard.
OPERATION IMPORTANT: All E-Max T™ brewers are tested and set a t the facto ry . If programming adjust- ments are necessary, refer to the E -Ma x™ Programming Manual (p/n 73674). To over-ride th e Br ew Wait mode , press and hold the BR EW key for 3 second s when the brewer is in Bre w Wait mode (i.
OPERATION (continued) WA R N IN G: Burn Hazard. This appliance dispenses very hot liquid. Serious bodily injury from scalding can occur from contact with dispensed liquids. C AUTION: B urn Hazard To avoid splashing or overflowing ho t liquids, ALWAYS use an empty dispenser before starting the brew cycle.
PROGRAMMING FEATURES AND OPTIONS 1. View Water Temperature in Ta nk: To view the water tem perature on the screen, E-Max T™ bre we r must be ON, and not brewing or in the filling mode. Press and hold the 4th key, and depress the 6th k ey . The actual water temperature w ill be displayed for 3 seconds.
8. Cl ock A. Time – Battery Backup. The E-Max T™ has a battery back up sy stem which will maintain the proper time during power failures, or when the brewer is unplugge d (e ven for very prolonged periods of time).
OPERATION (continued) 10 12. View Fil ter Statistics: To view filter statistics, turn the br e wer off. P ress and hold the 1s t ke y (Brew), and depress the 3rd (ON/OFF) k ey. Total water volume will be displa yed (TotalVol.). Press the 3rd k ey to view the Filter Lif e (F ltrLife :).
CLEANING I NSTRUCTIONS PROCEDURE: Clean Coffee Br e wer PRECAUTIONS: Disconnect brew er from electric power. Allow brewer to cool. FREQUENCY: Dail y TOOLS: Mi ld Detergent, Clean Sof t Cloth or Sponge Bristle Brush 1. Disconnect brewer from electric power.
FUNCTION 1. W ater enters at the inlet fitt ing of the fill solenoid (32). The s olenoid admits water via a command from the controller. N OTE: The solenoid has an inter nal strainer. To clean the s trainer: Shu t off water s upply. Unscre w the plast ic cap protruding f rom the rear of the brewer.
SERVICING IN STRUCTIONS — PLUM BING (continued) 13 ITEM DESCRIPTI ON P ART N0. USED ON 1 2 ASS E MBL Y , WA TER T ANK (120 V) 835 0 0 2030 6 GAS KET , T ANK LID 83499 2 030 9 TANK LI D 835 04 2 03 0 10 RET A INING CLIP , T ANK LID 83506 2 030 1 1 HO S E, V ENT (SIL I C O N E 4.
SERVICING INSTRUCTIO NS - ELECTRICAL FUNCTION 1. Pressing th e POWER k ey energizes the unit. The POWER LED will glow whenever the unit is ON . 2. Automatic fill is accomplished via the "FILL" section of the INLET SOLENOID (32) and a WATER LEVEL PROBE (7).
SERVICING INSTRUCTIONS - ELECTRICAL (continued) 15 ITEM DESCR IP TI ON P ART N0 . USED ON 3 PROBE, TEMPERA TURE 834 80 ALL 4 T HER M O ST A T , H I-L I M IT S A FE TY (1 20 V ) 8394 9 ALL 5 GROMME T ,.
SERVICING INSTRUCTIONS — DE-LIMING HE A TER TANK 1. Disconn e ct brewer form the electrical suppl y. Turn off the water suppl y and disconne ct water suppl y from the brewer inlet fitting. 2. R emove the top panel to gain acc ess to internal components.
TROUBLESHOOTING SUGGESTIONS If the E-Max T™ goes into the error m o d e as ou tlined belo w, it will likely be necessar y to reset the brewer in order to test individual com ponents.
E-Max T™ TEST PROGRAM 18 Instructions for testing procedures fo r the follow in g system components (using the E-Max T™ Built-In Diagnostic): Electronic Board Softwa re (Firmwa re) Re vision Keypad switches LED’s Inlet valve, Dump (Brew) valve, By Pass Valve Water level probe, Temperature probe A.
E-Max T™ TEST PROGRAM (continued) 19 E. LED Test The display should read “Testing LED’s”: Individual LED’s will be tested i ndividually, beginning with the first on the left, and proceeding thro ugh all six LED’s at one-second intervals. Screen will read “Testing LED’s” during the entire test.
EXPLODED VIEW & PARTS LIST 20.
EXPLODED VIEW & PART S LIST (continued) 21 ITEM P ART # DESCRIPTI ON QTY 1 8783-1 F A UCET , HOT W A TER 1 2 83500 T A NK ASSEM BL Y , 120V 1 3 83480 THERMISTOR , 5-½" 1 4 83949 THERMO, HI -.
WIRING DIAGRAMS (continued) 22.
NOTES 23.
PRINTED IN UNITED STATES OF AMERICA Bloo mf iel d Indu stri es, Inc . Division of Carrier Co mmercial Refrigeration In US and Can ada T elep hone: 775 -689- 5700 Fa x: 888-4 92-2783 Fa x: 800-3 56-5142 () websi te: www .
Ein wichtiger Punkt beim Kauf des Geräts Bloomfield 2030 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Bloomfield 2030 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Bloomfield 2030 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Bloomfield 2030 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Bloomfield 2030 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Bloomfield 2030 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Bloomfield 2030 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Bloomfield 2030. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Bloomfield 2030 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
