Benutzeranleitung / Produktwartung Snowplow 760HD des Produzenten Blizzard
Zur Seite of 52
Models 760L T , 760HD, 800HD & 860HD Inst allation Instructions & Owner's Manual April 1, 2006 Lit. No. B64090, Rev . 00 This document supersedes all editions with an earlier date. CAUTION Read this manual before operating or servicing snowplow .
April 1, 2006 2 Lit. No. B64090, Rev . 00 PREF ACE Congratulations on purchasing the finest straight blade snowplow available! BLIZZARD ® straight blades are clearing new trails for innovative design, rugged durability , quality craftsmanship and superior performance.
Lit. No. B64090, Rev . 00 3 April 1, 2006 Preface ....................................................................... 2 Safety Information ...................................................... 4 Operation .........................................
April 1, 2006 4 Lit. No. B64090, Rev . 00 SAFETY DEFINITIONS NOTE: Indicates a situation or action that can lead to damage to your snowplow and vehicle or other property .
Lit. No. B64090, Rev . 00 5 April 1, 2006 SAFETY PRECAUTIONS Improper installation and operation could cause personal injury , and/or equipment and property damage. Read and understand labels and the Owner's Manual before installing, operating or making adjustments.
April 1, 2006 6 Lit. No. B64090, Rev . 00 BA TTER Y SAFETY NOISE Airborne noise emission during use is below 70 dB(A) for the snowplow operator . SAFETY CAUTION Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lit tobacco to come near the battery .
Lit. No. B64090, Rev . 00 7 April 1, 2006 OPERA TION Y our snowplow is the most advanced and versatile straight blade on the market. The easy-to-use controls allow you to automatically adjust the plow blade into an infinite number of plowing positions.
April 1, 2006 8 Lit. No. B64090, Rev . 00 UNP ACKING & INSPECTION Y our BLIZZARD ® straight blade has been packaged to withstand transit and weather related damage. Fully inspect all components upon receipt of your plow . In the event of shipping damage or missing parts, immediately contact our Customer Service Department at 1-888-680-8600.
Lit. No. B64090, Rev . 00 9 April 1, 2006 TORQUE SPECIFICA TIONS Grade Identific ation for J429–Grade 5 Bolt Grade Iden tification for J4 29–Grade 8 Bolt SAE J429 Grade 5 Torque Values SAE J429 Gr.
April 1, 2006 10 Lit. No. B64090, Rev . 00 T ORQUE SPECIFICA TIONS 37° JIC Fl are Torque Values Turn s Size Ft-lbs min.max Assem bly Steps N/A -02 6-7 N/A -03 8-9 2 -04 11-12 2 -05 14-15 1-1/2 -06 18-20 1-1/2 -08 36-39 1-1/2 -10 57-63 1-1/4 -12 79-88 1 -14 94-103 1 -16 108-113 1 -20 127-133 1 -24 158-167 1 -32 245-258 1.
Lit. No. B64090, Rev . 00 11 April 1, 2006 MOLDBOARD & A-FRAME ASSEMBL Y 12-1/2" 1/8" Ground Clearance Spring Loaded Adjustable Pivot Beam Kickstand 1. Position the pivot beam and A-frame near the connecting points at the rear of the blade between the two center support ribs.
April 1, 2006 12 Lit. No. B64090, Rev . 00 B60007 - Manifold Ports #3 & 4 - Lift Cylinder Rod End 9/16 9/16 B60005 - Manifold Port #1 - Angle Cylinders 9/16 9/16 B60006 - Manifold Ports #3 & 4 9/16 9/16 B60072 - Manifold Port #2 9/16 9/16 B60272 - Lift Cylinder Base End 9/16 9/16 MOLDBOARD & A-FRAME ASSEMBL Y 5.
Lit. No. B64090, Rev . 00 13 April 1, 2006 MOLDBOARD & A-FRAME ASSEMBL Y 6. Remove the draw latch mount pin, spacer & cotter pin from the draw latch assembly . By removing this pin, the inner draw latch plates can swing free. Remove the inner draw latch plate lift cylinder mount pin.
April 1, 2006 14 Lit. No. B64090, Rev . 00 MOLDBOARD & A-FRAME ASSEMBL Y 7. Assemble the manifold. The manifold, pump and coil harness have been connected at the factory; however , the manifold contains several components that you will need to install prior to securing the assembly to the A-frame.
Lit. No. B64090, Rev . 00 15 April 1, 2006 Apply Thread-Locking Compound Apply Thread-Locking Compound MOLDBOARD & A-FRAME ASSEMBL Y 10. Secure the manifold to the A-frame. Remove the washers, split lock washers and cap screws from the manifold and align the mount holes with the A-frame brackets.
April 1, 2006 16 Lit. No. B64090, Rev . 00 GENERAL SYSTEM SCHEMA TICS RAISE S6 TGP PGP S3 T1 P1 S4 3000 PSI RIGHT ANGLE LEFT ANGLE 1 S5 2 RV 3 S8 LOWER FC LIFT CYL.
Lit. No. B64090, Rev . 00 17 April 1, 2006 HYDRAULIC GUIDE.
April 1, 2006 18 Lit. No. B64090, Rev . 00 ELECTRICAL INST ALLA TION – SNOWPLOW SIDE 1. Connect the red power wire from the plow harness to the pump motor terminal stud.
Lit. No. B64090, Rev . 00 19 April 1, 2006 ELECTRICAL SCHEMA TICS BLUE/BLACK PLOW HARNESS PLUG (2005) F ACE VIEW LOOKING A T MALE CONNECTOR VEHICLE HARNESS PLUG (2005) F A CE VIEW LOOKING A T FEMALE CONNECTOR BLIZZARD ® HARNESS PLUG (VEHICLE) UNIVERSAL 14 + 2 MOLD PIN COLOR FUNCTION A W G NO.
April 1, 2006 20 Lit. No. B64090, Rev . 00 ELECTRICAL SCHEMA TICS – SNOWPLOW SIDE G BLU/BLK H BLU/WHT J RED/BLK K RED/WHT (4) 6 AMP 600 VOLT ORG/BLK ORG/RED ORG/WHT WHT DIODES ORG ORG/BLK ORG/RED OR.
Lit. No. B64090, Rev . 00 21 April 1, 2006 ELECTRICAL SCHEMA TICS – SNOWPLOW SIDE ORG/BLK ORG/WHT 4 ORG/BLK ORG/RED ORG ORG/WHT WHT D4 ORG/RED ORG/WHT ORG/BLK ORG D3 D2 D1 ORG/RED ORG/BLK ORG ORG/WH.
April 1, 2006 22 Lit. No. B64090, Rev . 00 ELECTRICAL INST ALLA TION – VEHICLE SIDE 1. With the large plug on the electrical harness placed near the tow hook, under the bumper , route the harness over the driver-side fender well and to the fire wall.
Lit. No. B64090, Rev . 00 23 April 1, 2006 ELECTRICAL INST ALLA TION – VEHICLE SIDE 7. Remove the front signal light assembly from both sides of the vehicle. On the driver side, feed the violet (turn light) and gray (run light) wires from the main lighting harness through the opening in the signal light housing.
April 1, 2006 24 Lit. No. B64090, Rev . 00 ELECTRICAL INST ALLA TION – VEHICLE SIDE 12. Connect the power wire (with 15AMPFUSE) to a switched power source with a minimum of 15 amps. NOTE: The red power wire MUST be fused and switched on and off with ignition.
Lit. No. B64090, Rev . 00 25 April 1, 2006 ELECTRICAL SCHEMA TICS – VEHICLE SIDE 1 9 BRN – PUMP SOLENOID GRN/YEL FUSE CAP FUSE BODY SPRING FUSE 15AMP BRN/WHT RED VEHICLE HARNESS (2005) 2 RED/BLK .
April 1, 2006 26 Lit. No. B64090, Rev . 00 ELECTRICAL SCHEMA TICS – VEHICLE SIDE BLACK NOTE: ALL GROUNDS HAVE BLACK WIRE 6 BRN BRN/WHT 3 4GA BLK 4GA RED BLK 1 2 BRN RED/WHT RED/BLK BLU/WHT 4 5 BLK 1.
Lit. No. B64090, Rev . 00 27 April 1, 2006 ELECTRICAL SCHEMA TICS – VEHICLE SIDE D C A BLK B GRN/YEL AB A B EF AB OTHER WIRE B62016 WATER RESISTANT SPLICE LOCK CONNECTOR (USED IN INSTALLATION) JACKE.
April 1, 2006 28 Lit. No. B64090, Rev . 00 ELECTRICAL SCHEMA TICS – VEHICLE SIDE EF C A D B EF C A D B AB LT GRN/RED FROM VEHICLE HARNESS BLK VIO GRN/YEL BLK/WHT YEL/RED YEL YEL/BLK LT GRN B WHT/RED.
Lit. No. B64090, Rev . 00 29 April 1, 2006 POWER HITCH™ SYSTEM INSTRUCTIONS Prior to operating your straight blade snowplow , review the Mounting and Dismounting Instructions label on the back of the driver ’s side moldboard.
April 1, 2006 30 Lit. No. B64090, Rev . 00 TESTING YOUR SNOWPLOW 1. Fill the hydraulic pump reservoir with BLIZZARD ® SNOWPLOW RAPID ACTION HYDRAULIC OIL until it is approximately 3/4" from the top of the tank. Replace the cap on the reservoir .
Lit. No. B64090, Rev . 00 31 April 1, 2006 4. Return to the interior of the vehicle. T est the remaining functions of the snowplow . The system power on the control should be in the "ON" position. Raise the plow to its maximum height by pulling the joystick back (or down) or pressing the "U" button on the touchpad.
April 1, 2006 32 Lit. No. B64090, Rev . 00 HEADLIGHT AIMING Fully tighten headlight fasteners once correct visual aim is achieved. 1. Place vehicle on a level surface 25 feet in front of a matte-white screen, such as a garage door . The screen should be perpendicular both to the ground and to the vehicle centerline.
Lit. No. B64090, Rev . 00 33 April 1, 2006 MAINTENANCE Maintenance Periodical ly Year ly Check fa steners f or tightnes s. Torque to spe c ificat ions.
April 1, 2006 34 Lit. No. B64090, Rev . 00 TECHNICAL SPECIFICA TIONS Part Specification 760LT 760HD 800HD 860HD Length 90” (7'6") 90” (7'6") 96” (8’) 102” (8’6”) Thic.
Lit. No. B64090, Rev . 00 35 April 1, 2006 TROUBLESHOOTING Problem Cause Solution Plow harnes s may not be properly connect ed to the vehicle harne ss. Verify the harnesses are prop erly connec ted. Pump will not run. Power or ground cables to the battery, pump or solenoid may not be properly c onnecte d.
April 1, 2006 36 Lit. No. B64090, Rev . 00 TROUBLESHOOTING Problem Cause Solution Plow w ill not stay angled w hen plowing . The angle pre ssure relief v alve is set too low . NOTE: Increasi ng the pressure reli ef valve will c ause damage to yo ur plow .
Lit. No. B64090, Rev . 00 37 April 1, 2006 NOTES _________________________________________________________________________________________ _____________________________________________________________.
April 1, 2006 38 Lit. No. B64090, Rev . 00 MOLDBOARD & WING P ARTS – ALL MODELS 9 17 16 19 18 2 3 1 11 10 4 12 8 13 7 6 5 5A 14 15 8A.
Lit. No. B64090, Rev . 00 39 April 1, 2006 MOLDBOARD & WING P ARTS – ALL MODELS Qt y Item Part 760LT 760HD 800HD 860HD Description B81006 1 – – – B84006 – 1 – – B80006 – – 1 – .
April 1, 2006 40 Lit. No. B64090, Rev . 00 A-FRAME & PIVOT BEAM P ARTS – ALL MODELS Qt y Item Part 760LT HD Description B52153 1 – 1 B41041 – 1 Pivot Beam Weldment 2 B61357 7 7 Pin, Cott er,.
Lit. No. B64090, Rev . 00 41 April 1, 2006 A-FRAME & PIVOT BEAM P ARTS – ALL MODELS Qt y Item Part 760LT HD Description 3A B410 39 1 1 Kick stand Assembly Includes I tem 3–10 3 B41047 1 1 Kick.
April 1, 2006 42 Lit. No. B64090, Rev . 00 POWER UNIT P ARTS – ALL MODELS 1A 2 3 4 14 5 6 7 8 9 1 10 11 12 11 13 16 15 17 20 34 33 19 32 18 35 30 31 29 28 36 37 21 23 38 27 23A 24 25 26 17A 22 39.
Lit. No. B64090, Rev . 00 43 April 1, 2006 POWER UNIT P ARTS – ALL MODELS Item Part Qty Description 1A B60402 1 Hydraulic Pump Asse mbly Includes Item 1–2 & 4 –14 (M TE) 1 B60433 1 Reservoir 2 B60434 1 Motor, 12VDC 3 B60435 1 Seal Kit 4 B60436 1 Pump Asse mbly, 2.
April 1, 2006 44 Lit. No. B64090, Rev . 00 LIGHTS, DRA W LA TCH & CONTROL P ARTS – ALL MODELS 33 32 32A 34 35 18 26A 26 27 29 30 28 31 17 17A 19 20 24 21 22 23 25 15 16 13 14 9 5 4 2 3 8 7 10 11.
Lit. No. B64090, Rev . 00 45 April 1, 2006 LIGHTS, DRA W LA TCH & CONTROL P ARTS – ALL MODELS Qt y Item Part 760LT HD Description B82058 1 – 9 B40123 – 1 Draw Latch Finger Weldme nt B82033 1.
April 1, 2006 46 Lit. No. B64090, Rev . 00 HARNESSES, ACCESSORIES & KITS – ALL MODELS 5. Help channel air flow to your truck radiator during the long haul over the road. Mounted front and center , our custom airfoil redirects air over the top of the blade and into the grille of your vehicle.
Lit. No. B64090, Rev . 00 47 April 1, 2006 HARNESSES, ACCESSORIES & KITS – ALL MODELS 8. BLIZZARD ® hydraulic oil is specially formulated for use in BLIZZARD snowplows and can significantly enhance the operation and performance of the hydraulic system.
April 1, 2006 48 Lit. No. B64090, Rev . 00 HARNESSES, ACCESSORIES & KITS – ALL MODELS Ballast Retainer 14. Ballast (additional weight) is an important part of qualifying vehicles for snowplow eligibility . Rear ballast must be used when necessary to remain in compliance with axle ratings and ratios as specified by the vehicle manufacturer .
Lit. No. B64090, Rev . 00 49 April 1, 2006 HARNESSES, ACCESSORIES & KITS – ALL MODELS Qt y Item Part 760LT 760HD 800HD 860HD Description 1A B62039 1 1 1 1 Harness As sembly, Pl ow Incl.
April 1, 2006 50 Lit. No. B64090, Rev . 00 HARNESSES, ACCESSORIES & KITS – ALL MODELS Kits Qt y Item Part 760LT 760HD 800HD 860HD Description – B61354 1 – – – – B61353 – 1 1 1 Kit, Hardware, S nowplow Assembly Parts – B60276 1 1 1 1 Kit, Hydraulic A dapter Incl.
Lit. No. B64090, Rev . 00 51 April 1, 2006 NOTES _________________________________________________________________________________________ _____________________________________________________________.
April 1, 2006 52 Lit. No. B64090, Rev . 00 Copyright © 2006 Douglas Dynamics, L.L.C. All rights reserved. This material may not be reproduced or copied, in whole or in p art, in any printed, mechanical, electronic, film or other distribution and storage media, without the written consent of Blizzard.
Ein wichtiger Punkt beim Kauf des Geräts Blizzard Snowplow 760HD (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Blizzard Snowplow 760HD noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Blizzard Snowplow 760HD - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Blizzard Snowplow 760HD reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Blizzard Snowplow 760HD erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Blizzard Snowplow 760HD besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Blizzard Snowplow 760HD verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Blizzard Snowplow 760HD. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Blizzard Snowplow 760HD gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
