Benutzeranleitung / Produktwartung Nauticast AIS-300 des Produzenten ACR Electronics
Zur Seite of 32
.
2 Y1 -03 - 0222 Rev. C In the United State s W ARNING: It is a violat ion of the rules of the Federal Com m unications Comm ission to input an M MSI that h as not been pro perly assigned t o the end user, or to otherwise input any inaccurate data in t his device.
3 Y1 -03 - 0222 Rev. C Table of Contents SECTION 1 - WHAT IS AIS? ____________________________________________________________ 4 SECTION 2 - INSTALLATION ______________________________________________.
4 Y1 -03 - 0222 Rev. C SECTION 1 - W HA T IS A IS? 1. Overview AIS is an acronym for A utomatic I dentification S ystem . AIS increases navigational safety and collision avoidance b y transm itting vessel iden tification, h elping to r educe the d ifficulty of ide ntif ying ships w hen not in sight (e.
5 Y1 -03 - 0222 Rev. C On the bottom , a t ypical N auticast™ -B AIS installation in a comm on environm ent is shown. T he Nauticast™ -B AIS is connec ted t o the vess el ‟ s power supply, and, in connecti on with the VHF and GPS antennas, th e m inimal requirements for transpond er operation are f ulfilled.
6 Y1 -03 - 0222 Rev. C In order to m eet carriage re quirements f or Class A and Class B AIS s ystems, dedic ated GPS and VHF anten nas must be fit to the transponders. ACR has include d GPS and VHF antenn as that have been spec ifically designed, t ested and approved for use with the Nauticast ™ -B.
7 Y1 -03 - 0222 Rev. C 2. Installa tion overview and prerequisites In the United State s W ARNING: It is a violat ion of the rules of the Federal Com m unications Comm ission to input an M MSI that h as not been pro perly assigned t o the end user, or to otherwise input any inaccurate data in t his device.
8 Y1 -03 - 0222 Rev. C Or, when you have do wnloaded an upgr ade: Unzip the pack age when necessar y and start the installer prog ram as des cribed in “Installatio n of the Link2AIS™ Software” (later in this secti on). If one of the f ollowing dialogs is shown w hen the installation proc ess is started, the .
9 Y1 -03 - 0222 Rev. C W hen you are not connected to the internet, an error m essage like the one below will be shown. From the CD If you do not want to download the .
10 Y1 -03 - 0222 Rev. C W hen the i nstallation pro cess has finished, you MUST reboot your c omputer in order to install th e Link2AIS ™ Software: 6. Installation of the Link2AIS™ Software Unzip the downloade d pack age when necessary. Locate the files “setup .
11 Y1 -03 - 0222 Rev. C A dialog box will appear re m inding you to uninstall any prior v ersions of the L ink2AIS™ software ( if applicable) before c ontinuing the instal l process.
12 Y1 -03 - 0222 Rev. C The next screen will allow you to pick options to be installed. T hese options ar e check ed by default. Choose a director y where the software will be installed . Make note of this d irectory, as you will need to manuall y copy files to this location later on in the instal l process.
13 Y1 -03 - 0222 Rev. C The software will ask you to choose a locati on in the Start m enu to place the pro gram‟s s hortcuts: The next screen will ask y ou to co nfirm the install sett ings you hav.
14 Y1 -03 - 0222 Rev. C Now the application will install autom atically in the folder you have chosen : The install program will tell you when ins tallation has b een completed. C lick Finish. Finally, find the Coas tlines folder on the insta llation CD and copy to the insta ll directory chosen dur ing the install process.
15 Y1 -03 - 0222 Rev. C You will find the instal led program shortcuts i n the Star t Menu / All Programs/ ACR Electronics director y (unless you chose a dif ferent location durin g the install proc ess) . A shortcut nam ed “Link2AIS” will be place d on your desk top.
16 Y1 -03 - 0222 Rev. C Start up Link2AIS ™ Softwa re program on PC . The initial app lication screen wil l appear as shown: The application requires a serial connec tion to a N auticast™ - B AIS trans ponder. Connect the transponder to an available serial port.
17 Y1 -03 - 0222 Rev. C To configure the transpo nder all of the dat a fields m ust be completed and sa ved to the AIS. WARNING: Per FCC rules (United States us ers only) the static data of the vesse l cannot be c hanged once programm ed. Do not progr am the static data un less you are certain y ou have the correct information.
18 Y1 -03 - 0222 Rev. C For additional software applications unrel ated to the installation, please ref er to the Link2AIS™ Software user guide for technical s upport. 11. Hardware installation WARNING : T he compass safe distance of this unit is 0.
19 Y1 -03 - 0222 Rev. C If using PC s erial term inal with third part y AIS ca pable Elec tronic Charting Soft ware, connect the user end of the data interface c able to the displa y device. The sof tware in the displ ay device m ust be configured for AIS operation AND to accept st andard Class B AIS operation NMEA sentences.
20 Y1 -03 - 0222 Rev. C The GPS antenna has a free view through 360 degrees with a vertical angle of 5 to 90 degre es above the horizon. The GNSS antenna i s placed as far away as possib le from radar, Inmarsat and Irid ium transmitters . Also ensure that the GPS ante nna is free from direct view of the radar an d the Inm arsat beam.
21 Y1 -03 - 0222 Rev. C If the r ed LED i lluminates continuously, the un it should be ass umed to be f aulty. It s hould either b e s witched off (power r emoved) or, if this is not prac tical, any other vessel position inform ation derived f rom the unit should not be used.
22 Y1 -03 - 0222 Rev. C TX timeout This is a yellow LED which indicates when lit that t he CST DMA transm itter is prevent ed from transm itting. Reasons for this include the following: The transpond er‟s intern al GPS r eceiver is not yet r eady. The y ello w LED will go out a nd the green LED will light when G PS receiver is read y.
23 Y1 -03 - 0222 Rev. C Data A minimum keypad and d ispla y (MKD) unit, chart plotter or other d isplay device may be connected to the N auticast™ -B AIS unit via the a ppropriate cable assem bly. The default baud rate of the data link is 38.4k baud with 8 data b its, one stop bit and no parit y.
24 Y1 -03 - 0222 Rev. C NOTE 2 The sequential mess age identifier prov ides a message identification num ber from 0 to 9 that is sequentially assigned and is increm ented for each new m ulti -sentence m essage.
25 Y1 -03 - 0222 Rev. C 5. VHF data link own vessel messages (NME A 0183 VDO) This mess age describes your own vessel m essage being sent. VDO message f ormat ! -- VDO,x1,x2,x3,a,s -- s ,x*hh<CR>.
26 Y1 -03 - 0222 Rev. C 6. Regional Assignment Channel Assignment Message (NMEA 0183 ACA) A N auticast™ - B unit ca n receive regional channel m anagem ent inform ation in t wo ways: ITU -R M.1 371 message 22 or a DSC te lecom m and received on channel 70.
27 Y1 -03 - 0222 Rev. C 8. AIS alarm messa ges (NMEA 0183 ALR, Text) Local alarm condition and status. T his sentence is us ed to report an alarm condition on a device and its current state of ack nowledgement. ALR message format ! -- ALR,hhmmss.ss,xxx ,A,A,c -- c*hh<CR><LF> field 1 2 3 4 5 Field Format Description 1 x hhmmss.
28 Y1 -03 - 0222 Rev. C A PPENDIX B - SPEC IFICATIONS AN D WARNINGS 1. Specifications Parameter Value Dimensions 7.8 x 6.22 x 1.84 in. ( 198 x 158 x 46.
29 Y1 -03 - 0222 Rev. C 2. Warnings WARNING regarding VHF antenna connectio n: Connecti ng a badl y mismatc hed VHF antenna, leav ing the VHF antenna port d isconnected, or s horting the V HF antenna .
30 Y1 -03 - 0222 Rev. C A PPENDI X D - DATA POWER C AB LE I NFOR M A TION Class B A2 - 07 -0196-1 DATA POWER CABLE J1 J2 Description DB15 DB9 Wire Type Color AWG CABLE # 12V + 1 Tinned Copper RED 18 C.
31 Y1 -03 - 0222 Rev. C APPENDIX E - SUPPORT, W A RRANTY, USEFUL LIFE and NOTICES 1. Support Contact your local deal er for Nauticast™ -B AIS support.
32 Y1 -03 - 0222 Rev. C EC DECL A R ATION OF CO NFORMITY ACR Electronics, Inc . hereby declares that the following pro duct is in conform ity with Directive 19 99/5/EC of the European Parliam ent and o f the Council of 9 March 1999 on Radio eq uipm ent and Telecomm unications Term inal Equipment (R&TTE), and h as been t ype examined as follows.
Ein wichtiger Punkt beim Kauf des Geräts ACR Electronics Nauticast AIS-300 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie ACR Electronics Nauticast AIS-300 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für ACR Electronics Nauticast AIS-300 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von ACR Electronics Nauticast AIS-300 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über ACR Electronics Nauticast AIS-300 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon ACR Electronics Nauticast AIS-300 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von ACR Electronics Nauticast AIS-300 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit ACR Electronics Nauticast AIS-300. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei ACR Electronics Nauticast AIS-300 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
