Benutzeranleitung / Produktwartung SRP-275A des Produzenten Bixolon
Zur Seite of 39
User's Manual SRP-275 Ve r. 2 Imp act Printer Rev . 2.00 http://www .bixolon.com.
Rev . 2.00 - 2 - SRP-275 Ve r. 2 ■ Safety Precautions In using the present appliance, please keep the following safety regul ations in order to prevent any hazard or material damage. W ARNING Violating following instructions c an cause serious injury or death.
Rev . 2.00 - 3 - SRP-275 Ve r. 2 CAUTION Violatin g follow ing inst ructions c an cause sli ght wound or dam age the app liance . Do not use the printer when it is ou t of order . This can cause a fire or an electro cution. • Switch off and unplug the printer before calling your dealer .
Rev . 2.00 - 4 - SRP-275 Ve r. 2 All rights reserved. No part of this publicati on may reproduced, stored in a retrieval, or transmitted in any form or by any means, elec tronic, mechanical, photocopying, recording, or otherwise, without the prior wr itten permission of BIXOLON.
Rev . 2.00 - 5 - SRP-275 Ve r. 2 ■ EMC and Safety standards Applied Product Name : SRP-275 The following standards are applied only to the printers that are so labeled.
Rev . 2.00 - 6 - SRP-275 Ve r. 2 ■ Introduction The SRP-275 is a high- quality impact printer . This one-station printer has the following features. • Compact design and light-weight. • High-speed printing using logic-seeking (5.1LPS). • Easy to use : Easy paper loading.
Rev . 2.00 - 7 - SRP-275 Ve r. 2 ■ T able of Content s 1. Setting Up the Prin ter··························································.
Rev . 2.00 - 8 - SRP-275 Ve r. 2 1. Setting Up the Printer 1-1 Unpacking Y our printer box should include the it ems sho wn in the illustration below. If any items are damaged or missing, please cont act your dealer . 1-2 Choosing a place for the printer • Avoid locations that are subject to direct sunli ght or excessive heat.
Rev . 2.00 - 9 - SRP-275 Ve r. 2 1-3 Using the operation panel Most of the functions of this printer are governed by software, but you ca n monitor the printer s statu s by looking at the lights on the control panel and for some procedures you will u se the buttons.
Rev . 2.00 - 10 - SRP-275 Ve r. 2 2. Connecting the cables 2-1 Connecting the AC Adaptor CAUTION Before connecting the printer to the power supply, ma ke sure that the voltage and power specification s match the printer’s requirem ents. Using an incorrect pow er supply can cause seri ous damage to the printer.
Rev . 2.00 - 1 1 - SRP-275 Ve r. 2 2-2-1 Serial Interface (RS-232C) IFC-S TYPE Interface connector Drawer kick-out Connector (F.G) 1 (TXD) 2 (RXD) 3 (RTS) 4 (CTS) 5 (DSR) 6 (S.G) 7 (DTR) 20 1 (F .G) 2 (RXD) 3 (TXD) 4 (DTR) 5 (S.G) 6 (DSR) 7 (RTS) 8 (CTS) PRINTER SIDE (25Pin) HOS T SIDE (9Pin ) Pin No.
Rev . 2.00 - 12 - SRP-275 Ve r. 2 2-2-2 Parallel Interface (IEEE1284) IFC-P TYPE Interface connector Drawer kick-out Connector Pin no. Source Comp atibility mode Nibble mode Byte mode 1 Host nS trobe .
Rev . 2.00 - 13 - SRP-275 Ve r. 2 2-2-3 USB Interface IFC-U TYPE Interface connector Drawer kick-out Connector Pin No. Signal name Assignment (Color) Function Shell Shield Drain wire Frame ground 1 VB.
Rev . 2.00 - 14 - SRP-275 Ve r. 2 3. Setting the Switches 3-1 Setting the DIP Switch Although the factory settings are best for almost all user s, if you have special requi rements, you can cha nge the DIP Switch. Your printer has two sets of DIP Swit ches.
Rev . 2.00 - 15 - SRP-275 Ve r. 2 3-1-1 DIP Switch setting for Citizen(iDP 3550) mode • DIP S witch 1 Sw it ch Function ON OFF Default 1-1 1-2 Emulation Selection (*1) Refer to the following table O.
Rev . 2.00 - 16 - SRP-275 Ve r. 2 3-1-2 DIP Switch setting for Star(SP500) mode • DIP S witch 1 Sw it ch Function ON OFF Default 1-1 1-2 Emulation Selection (*1) Refer to the following t able OFF 1-.
Rev . 2.00 - 17 - SRP-275 Ve r. 2 3-1-3 Changing the DIP Switch setting If you need to change settings, follow the st ep s below to make your changes. CAUTION Turn off the printer before removing the DIP Switch co ver to prevent an electri c short, which can damage the printer.
Rev . 2.00 - 18 - SRP-275 Ve r. 2 3-2 Setting the Memory Switches This printer has “Memory Switch” set which is sof tware switches. Memory Switch set has “MSW 2”, “MSW 8”, “Customize value”, “Se rial communication co ndition”.
Rev . 2.00 - 19 - SRP-275 Ve r. 2 • Memory Switch 8 Sw it ch Function On Off 1 Upside down On Off 2 Font Selection Font B Font A 3 Selection Paper End Buzzer Off On 4 Reserved Fixed to Off 5 Selecti.
Rev . 2.00 - 20 - SRP-275 Ve r. 2 • Memory Switch Setup Mode The following items are specified in the Memory Switch setup mode: Basic Serial communication con dition (Serial communication ) - T rans.
Rev . 2.00 - 21 - SRP-275 Ve r. 2 • Procedure of Memory Switch setting ① Re se tti ng B as i c Se r i a l I nt e r f ac e? Baud ra te Cu rrent s e tt i ng: 96 00 b p s 19 20 0b p s 48 00b p s 24 0.
Rev . 2.00 - 22 - SRP-275 Ve r. 2 3-2-1 Memory Switch setting for Star mode • Settings Memory Switches are from MSW 0 to MSW 8. They are stored in non-volatile memo ry (flash memory ). T o change the settings, send the followin g commands from the host.
Rev . 2.00 - 23 - SRP-275 Ve r. 2 • Default Settings The default settings for Memory Switch 0 to Memory Switch 8 are shown below . Settings vary for single byte character countries (s ta ndard specifications (SBCS )) and for double-byte character count ries (Chinese char acter specification s (DBCS)).
Rev . 2.00 - 24 - SRP-275 Ve r. 2 • Function - Memory Switch 0 Bit Function 0 1 F~C Reserved B~A Red and Black (inverted black and white) Commands (*3) Refer to the following table 9~5 Reserved 4 Co.
Rev . 2.00 - 25 - SRP-275 Ve r. 2 - Memory Switch 1 Bit Function 0 1 F Reserved E~5 4 Zero style Normal Slash zero 3~0 International Cha racters (*1) Refer to the following t able NOTES (*1) International Characters D efault Value Settings MSW1-3 MSW1-2 MSW1-1 MSW1-0 International Characters 0 0 0 0 U.
Rev . 2.00 - 26 - SRP-275 Ve r. 2 - Memory Switch 3 Bit Function 0 1 F~D C~8 Character T able (*2) Refer to the f ollowing table 7~2 1~0 <CR> Command Functions (*1) Refer to the following t able.
Rev . 2.00 - 27 - SRP-275 Ve r. 2 - Memory Switch 4 Bit Function 0 1 F~9 8 Automatic S tatus Function Disabled Enabled 7~4 3 ESC RS a n command function Only Setting Auto-status sent only once 2~1 0 D.
Rev . 2.00 - 28 - SRP-275 Ve r. 2 4. Ribbon Cassette Installation NOTES Malfunctions and other pro blems may arise if other t han specified ribbon cassettes are u sed in the printer . The W arranty may be void if other than specified ribbon ca ssettes are used.
Rev . 2.00 - 29 - SRP-275 Ve r. 2 5. Roll Paper Installation CAUTION Do not touch the auto cutter blade when you open rea r cover. 1) To prevent data loss, make sure that the printer is not receiving data. 2) Open the rear cover by pushing the ope n button.
Rev . 2.00 - 30 - SRP-275 Ve r. 2 6. Changing the paper width Sc rew (3x6 )(2p iec es) F ra me pa pe r c on tro l 57.5mm 69.5mm 76mm(d efault) 1) Open the rear cover . 2) Remove the frame pa per control by loosing the two screws(3×6) . 3) Reattach the frame paper control in you want .
Rev . 2.00 - 31 - SRP-275 Ve r. 2 7. Installing the wall mount (Option) Brack et han ger Screw( 3 x5) (4pi ec es) Brack e t mo unt Screw( 4x10) (8pi eces) 1) Turn the Set over and attach the Bracket hanger to the Frame ba se then tighten four screws. 2) Attach the Bracket mount to the wall firmly with the eight screws.
Rev . 2.00 - 32 - SRP-275 Ve r. 2 8. Self Test The self test let you know if your printer is operating properly . It checks the printing quality , ROM version, DIP Switch settings, mem ory switch sett ings and stat istic data.
Rev . 2.00 - 33 - SRP-275 Ve r. 2 9. Hexadecimal Dumping • Hexadecimal dump This feature allows experience d users to see exactly what data is coming to the printer.
Rev . 2.00 - 34 - SRP-275 Ve r. 2 10. Specification 10-1 Printing specification Item Description Remark Printing method Serial impact method Head wire 9 pin serial type Dot pitch 0.352mm (1/72”) Dot wire diameter 0.28mm (0.01”) Printing direction Bidirectional (logic seeking) with friction feed Characte rs per line Ma x.
Rev . 2.00 - 35 - SRP-275 Ve r. 2 10-4 Electrical characteristics Item Description Remar k SMPS Supply voltage 24VDC Operating Mean : Approximately 0.5A Peak : Approximately 1.5A Current consumption (at 24V , except for drawer kick-out driving) S tandby Mean: Approximately 0.
Rev . 2.00 - 36 - SRP-275 Ve r. 2 10-7 Dimensions & weight • Dimensions • Weight Approx. Wt. : 2.5 kg Shipping Wt. : 4.0 kg 10-8 Optional features The optional features either replace a st andard feature or enhance the operation of the printe r .
Rev . 2.00 - 37 - SRP-275 Ve r. 2 11. Appendix - Troubleshooting This chapter gives solutions to so me printer problems you may have. 11-1 ERROR LED blinking pattern The printer stops all printe r operations for the sele cted paper section, goes off lin e, and the ERROR LED blinks when an error is detected.
Rev . 2.00 - 38 - SRP-275 Ve r. 2 • Errors that are impossible to recov er Error Description ERROR LED blinking p attern Recovery R/W error in memory or gate array After R/W checking, the printer does not work correctly . Writing to, reading out, or erasing the NV memory for image scanning results does not work correctly .
Rev . 2.00 - 39 - SRP-275 Ve r. 2 11-3 The printer stops printing • If the ERROR LED is on (but not blinking), the printer is off line. Check to see that the covers a re closed and check the pap er state. See Chapter 5 for instruct ions on inst alling or replacin g the paper roll.
Ein wichtiger Punkt beim Kauf des Geräts Bixolon SRP-275A (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Bixolon SRP-275A noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Bixolon SRP-275A - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Bixolon SRP-275A reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Bixolon SRP-275A erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Bixolon SRP-275A besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Bixolon SRP-275A verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Bixolon SRP-275A. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Bixolon SRP-275A gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
