Benutzeranleitung / Produktwartung ZSR1134WE des Produzenten Zonet
Zur Seite of 44
.
Copyright State ment is the re gistered trademark of Zonet T echnology Inc. All the products and product names mentio ned herein are the trademarks or registered trademarks of their respective holder s. Copyright of the whole product as in tegration, including its accessor ies and software, belongs to Z onet T echnology Inc.
Table of Conten ts Chapter 1 Introduction ......... ....... ........ ....... ........ ........ .... ....... ........ ....... 1 W e lcome . ....... ........ ........ ....... ........ ..... ....... ....... ........ ....... ........ ....... ...... 1 Contents of P ackage .
1 Chapter 1 Introduction Welcome Thank you for purchasing Z onet ZSR1134WE – 802.11g w ireless broadband router! Thi s h igh cost -efficiency router is the best choice for Small office / Home office users, all co mputers and network devices can share a single xDSL / cable modem in ternet co nnection at high sp eed.
2 Getting to Kno w Your ZSR1134WE Front Panel LED Indicator Status Description ON Indicates ZSR1134WE is receiving power SYS Flashing Indicates ZSR1134WE works normally.
3 Rear Panel Item Name Description POWER P ower connector , connects to power ad apter 1-4 (LAN Ports) Local Area Network (LAN) ports 1 to 4 WAN Wide Area Network (WAN / Internet) port. DEFAULT Res et ZSR1134WE to factory default settings (clear all settings).
4 Chapter 2 Hardware Installation Please follow the following instruction to bu ild the network connection between your ZSR1134WE and y our computers, network devices: 1. Connect th e power adapter to the wall socket, and then connect it to the Power socket of ZSR1134WE.
5 3. Connect your xDSL / cable modem to the WAN port of ZSR1134W E by Ethernet cable. 4. Please check all LEDs on the front panel. SYS LED s hould be s teadily on, WAN and LAN LEDs shoul d be on if the computer / network device connected to the respective port of ZSR1134WE is powered on and cor rectly connected.
6 Chapter 3 Connect Your ZSR11 34WE How to Set the Network Config urations for My Computer 1. Click Start → → → → Control Panel 2. Click Network and Internet Connections → → → → Networ.
7 3. Right click Local Area Netwo rk Connection and select Properties . 4. Select Internet Proto col (TCP/IP) and click Properties ..
8 5. Select Obtain a n IP addres s autom atically and Obta in DNS server address automatically . Click OK to save the configur ations. Additional Setti ngs for Wireless Client If you choose to access ZSR1 134WE via a wireless client, please also verify the following: 1.
9 How to Check t he Network Conn ection 1. Select Start → → → → Program s → → → → Accessories → → → → Command Prompt . 2. Input ping 192.168.1.1 and press Enter . If the screen displays as below, it means your PC is connected to y our rou ter successfully .
10 Chapter 4 Basic Confi gurations This section is to sh ow you how to confi gure your new Z SR1134WE through the W e b-based Configuration Utilit y . How to Access t he Web-based Conf iguration Utility 1.
1 1 Quick Setup Wizard 1. When Convenient Setup show up, Click Next to continue. a. Operation Mode.
12 Gateway ZSR1134WE is supposed to connect to Internet via ADSL/Cable Modem. The NA T is enabled and PCs in four LAN por ts share the same IP to ISP through W AN port. The co nnection type can be setup in WAN page by using PPP oE, DHCP client, PPTP client or static IP .
13 c. LAN Setup LAN Setup page allows y ou to specify a private IP address for ZSR1134 WE’ s LAN ports as well as a subnet mask for your LAN segment. I P Address ZSR1134WE’ s LAN IP address (not your PC’ s IP address). Once you modify the IP address, you need to remember it for the W eb-based Utility login next time.
14 St atic IP Y our ISP has given you an IP address already DH CP Client Y our ISP w ill au tomatically giv e you an IP add ress. And the n cl ick Next . PPPoE Y our ISP requires PPPoE connecti on PPTP Y our ISP requires you to use a Point -to-P oint T unneling Protoco l (PPTP) connection.
15 f. Wireless Security Encryp tion Mode ZSR1134WE provides security authentication methods including: None, WEP, WPA(TKIP), WPA2(AES) and W PA2 Mixed. None means do not encrypt wireless data. WEP WEP (Wired E quivalent Privacy) is an encryption method used to protect your wire less data co mmunications.
16 LAN Setup I P Address ZSR1134WE’ s LAN IP address (not your PC’s IP addre ss). Once you modify the IP addr ess, you need to remember it for the W e b-based Utility login next time. Default v alue is 19 2.168.1.1 Subnet Ma sk ZSR1134WE’ s subnet mask for measurement of th e network s ize.
17 Clone MAC addr ess Replace the LAN MAC address with the MAC address of that PC. Internet Setup W AN Access Type Static IP address IP address provided by your ISP .
18 M TU Maximum T ransmission Unit. It is the size of largest datagram that can be sent over a network. The de fault v alue is 1412. Do NOT modify it unless necessary .
19 Chapter 5 Wireless Settings Basic Settings Band Support 802.11b/g mixed, 802.11b and 802 .11g modes. Mode Support AP , Client, WDS, AP+WDS mode. Network Type Support infr astructure and hoc. SSID It’ s the name of your wireless network.
20 Enable Mac Clone Click the Enable M AC Clone checkbox will copy the MAC address of your PC to the WLAN MAC. Enable Universal Repeater Mode T o Enable Universal Repeater M ode, Acting as AP .
21 Fr agment Threshold Specify the maxi mum size of packet during the fr agmentation of dat a to be tran smitted. Default value is 2346. RTS Threshold When the pack et size is small er t he R TS threshold, ZSR1134WE will not use the RTS/CTS mechanism to send this packet.
22 Security Setup a. None.
23 b. WEP (Set WEP Key) WEP (Wired Equivalent Privacy) is an encryption method u sed to protect your wireless data communications. WEP uses a combination of 64 -bit or 128-bit keys to provide access control to your network and encryption security for every data transmission.
24 c. 802.1x This security mode is used when a RADIUS ser ver is co nnected to ZSR1134WE. IEEE 802.1x is an auth entication protocol. Every use r must use a v alid accoun t to login to ZSR1 134WE befo re accessing the w ireless LAN. The authentication is proce ssed by a RADIUS server .
25 d. WPA Wi-Fi Protected Access (WP A) is a n advanced security standar d. It uses TKIP and AES to change the encryption key fre quently. WPA Cipher Suite Select one encryption type, TKIP or AES .
26 Access Control This function wi ll help you to prevent un authorized use rs from co nnecting to ZSR1134WE; only those wireless devices who hav e th e MAC address you assigned her e can gain access to your Z SR1134WE. Y ou can u se this function wi th o ther security measure s described in previous section, to create a safer wireless environment.
27 Disable WPS Select the checkbox to disable WPS function, default setting is Enable . WPS Status Configured: means WPS feature is enabled and goes into effe ct. UnConfigured: means WPS is not use d. Self-PIN Number ： ： ： ： The PIN code used by default.
28 Note: First, you should set ZSR1134 WE in AP mode a t Wireless Basic Settings page, and then select the Enable WDS checkbox in th is page. Two wireless routers must use the same band, channel number, and security setting.
29 Chapter 6 Advanced Settings Applications & Gaming a. Virtual Service When you want differe nt servers/clients in your LAN to handle different service/Internet application type (e.g. Email, FT P , W eb server etc.) from the Internet, you ca n u se the Virtual Serv er function.
30 b. DMZ The DMZ(Demilitarized Z one) funct ion is to allow one co mputer in LAN t o be exposed to the In ternet for a special-purpose ser vice as Internet gaming or videoconferencing. Enable DMZ Select the checkbox to enable the DMZ host. DMZ Host IP Address The IP address of the computer you want to expose.
31 Security Manag ement T o benefit your further management to the computers in the L AN, you can control some ports access to Internet by data packet filter function. a. Port Filtering Enable Port Filtering Select the checkbox to enable port filtering Port Range Enter the port r ange over the protocol for access poli cy .
32 b. IP Filtering Enable IP Filtering Select the checkbox to enable IP filtering Local IP Address Enter the IP address you wan t to run t he access policy .
33 Enable MAC Filtering Select the checkbox to enable MAC filtering MAC Address Enter the MAC address you want to run the access policy . d. URL Filtering If you want to pre vent computers in .
34 Chapter 7 System tools System Informat ion a. Status The Status page allows you to monitor current status of ZSR1134 WE..
35 b. Statistics c. System Log Refresh: Click to update the log. Clear: Click to clear the current shown log..
36 DDNS DDNS (Dynamic Domain Name System) is to assign a fix ed host and domain name to a dynamic Internet IP address, which is used to monitor hosting website, FTP server and so on behind ZSR1134WE. If you want t o activate this function, please select Enable and a DDNS service provider to sign up.
37 System Manag ement a. Time Zone Setting Time Zone Select your time zone from the drop-down menu. N TP Server Manually assign time server address if the defaul t time server does not work.
38 Browse Click to browse the path to the upgraded firmware f iles. Upload Click to start upgr ade. IMPORTANT: D o not power off the system during the f irmware upg rade to avoid damaging. ZSR11 34WE will reboot automatical ly after th e upgrade.
39 d. Password Setup User Nam e Enter a new user name. N ew Password Enter a new password. Confirmed Pas sword Re-enter to confirm th e new password. NOTE: It is hig hly recommend ed to change the password to secure your network and ZSR113 4WE.
40 Appendix 1: Troublesh ooting Q1. I cannot access the Web-based Configurat ion Utility from the Ethernet computer used to configure ZSR1134WE. Check whether the LAN LED is on. If the L ED is not o n, verify the cable for the LAN connection is firmly connected.
41 Q4. I can browse ZSR1134WE’s Web-based Configurat ion Utility but cannot access the Internet. Check if the WAN LED is ON. If not, verify that the physical connection between ZSR1134WE and the DSL/Cable modem is firmly connected. Also ensure the DSL/Cable modem is working properly.
Ein wichtiger Punkt beim Kauf des Geräts Zonet ZSR1134WE (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Zonet ZSR1134WE noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Zonet ZSR1134WE - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Zonet ZSR1134WE reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Zonet ZSR1134WE erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Zonet ZSR1134WE besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Zonet ZSR1134WE verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Zonet ZSR1134WE. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Zonet ZSR1134WE gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
