Benutzeranleitung / Produktwartung ZXP S3 des Produzenten Zebra
Zur Seite of 116
P1032297-001 Rev . A Zebra ® ZXP Series 3 ™ Card Printer User’s Manual.
Copyright Notice © 2010 ZIH Corp. This document contai ns information prop rietar y to Zebra T echnologies Corporation. This document and th e information contai ned within i s Copyrighte d by Zebra T echnologies Corporation and may not be duplicated in full or in part by any perso n without writte n approval from Zebra.
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual iii Contents 1 • Getting St arted . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ZXP Series 3 Part Numbers . . . . . . . . . . . . . . . . . . . .
iv Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Content s 3 • Printer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Printer Features . . . . . . . . . . . . . . . . . . . . . . . . .
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 1 1 Getting Started This manual contains installation and operatio n information for the Zebra ZXP Series 3 Card Printer, manufactured by Ze bra T echnologies Co rporation. The printer provid es full color dye sublimatio n or monochrome thermal transfer printin g on standard 2.
2 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Getting S t arted ZXP Series 3 Part Numbers ZXP Series 3 Part Numbers The Pa rt Number of a parti cular Ze bra ZXP Series 3 Card Prin ter is sh own on a label af fixed to the bottom o f the printer; that Part Number i dentifies the spe cific co nfiguration for that print er .
Getting S tarte d Features, Controls, and Indica tors P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 3 Features, Controls, and Indicators The picture be low points out some of the printer ’ s external features; see Section 3 for an interior vie w .
4 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Getting S t arted Rear Panel Conne ctors Rear Panel Connectors St andard USB Connection The figure below sho ws the rear of th e Printer with the USB interface .
Getting S tarte d Multi-Functio n LCD Panel P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 5 Multi-Function LCD Panel Y o ur printer is equippe d with a Multi-Function LCD Pan el to provide printer st atus information. The readout is con trolled by the M ulti-Function Cont rol Button d irectly below the viewin g window .
6 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Getting S t arted Multi-Function LCD Panel W arning Messages W arning messages alert the opera tor to action t hat should be taken; the printe r will general ly continue op eration.
Getting S tarte d Multi-Functio n LCD Panel P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 7 Icons Throughout t his manual, di ffer ent icons high light important in formation, as fo llows: Product Disposal Note • Indicates information that emphasizes or supplements important poi nts of the main text.
8 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A.
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 9 2 Printer Installation Unp acking Y our Card Printer Y o ur ZXP Series 3 Card Pri nter ships in a cardb oard carto n, p rotected by styrofoam i nserts and a protective anti-st atic bag.
10 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Inst allation Installing the Printer Inst alling the Printer Setting up the Printer St e p 1 . Place t he printer in a loca tion that allows ea sy a ccess to all side s. The printer sho uld never be operated while resting on i ts side or upside do wn.
Printer Inst allation Installing the Printer P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 1 1 Connecting Power St e p 1 . Insert the power supp ly plug into the po wer socket,.
12 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Inst allation Installing the Printer Connecting the Printe r to your Computer St e p 1 . If your p rinter has only the USB interface, attach the included USB cable to your computer and the printer .
Printer Inst allation Viewing Printer Information P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 13 V iewing Printer In formation T o check the config uration parameters o f the printer wi thout being co nnected to a comp uter: St e p 1 .
14 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Inst allation Installing the Windows Printer Driver Inst alling the Windows Printer Driver Initial S tep s Each computer th at will use the p rinter must have the Prin ter Driver installed.
Printer Inst allation Installing the Windows Printer Driver P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 15 Inst alling the USB Printer Driver St e p 1 . If not a lready done, connec t power to the printe r . Do not turn power ON.
16 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Inst allation Installing the Windows Printer Driver St e p 9 . The InstallShield W izard window wil l open. T o proceed with the install ation, click the Next button. St e p 1 0 .
Printer Inst allation Installing the Windows Printer Driver P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 17 St e p 1 2 . This will bring u p the License A greement window . T o p roceed with the installation, click the Ye s button.
18 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Inst allation Installing the Windows Printer Driver St e p 1 4 . This will brin g up th e Select Program Folder window . T y pe i n a new fo lder name or select one from the existing folders list, and click t he Next button.
Printer Inst allation Installing the Windows Printer Driver P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 19 St e p 1 6 . The Congrat ulations window will appe ar . St e p 1 7 . At th is point, turn on your printer ; and then click the Next button.
20 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Inst allation Installing the Windows Printer Driver Inst alling the Ethernet Printer Driver St e p 1 . If not a lready done, co nnect power to t he printer . T urn power ON.
Printer Inst allation Installing the Windows Printer Driver P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 21 St e p 8 . In the We l c o m e wind ow , choose the maintena nce operation to be performed: a. Select Mod ify to up date the older printer driver , click the Next button, and follow the screen p rompts.
22 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Inst allation Installing the Windows Printer Driver St e p 11 . This will brin g up the License Agreeme nt window . T o proceed with t he installation , select the I accept the t erms of the license agr eement option , and then click the Next button.
Printer Inst allation Installing the Windows Printer Driver P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 23 St e p 1 3 . Setup will find and list al l Zebra ZXP Series 3 Prin ters on the netwo rk. Select a printer from t he list (example, arro w below); and cl ick the Next button.
24 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Inst allation Installing the Windows Printer Driver St e p 1 5 . Obser ve the Setup S tatus window . St e p 1 6 . The Congrat ulations window will appe ar . St e p 1 7 . At th is point, click the Next button.
Printer Inst allation Installing the Windows Printer Driver P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 25 St e p 1 8 . When the InstallShield Wizard Complete window appears, click the Finish butt on. St e p 1 9 . This completes Ethernet driver instal lation.
26 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A.
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 27 3 Printer Setup Printer Features The following sh ows an interior view o f the ZXP Series 3 Card Printer.
28 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Setup Loading Ribbon Cartri dge Loading Ribbon Cartridge The Printer requires ap pr oved ribbon cartridges. The Resin Thermal T ransfer and Dye Sublimation ribbons are specifical ly designed for your Printer .
Printer Setup Loading Ribbon Cartri dge P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 29 3. Insert the ri bbon cartridge wi th t he clea ning ro ller facing do wn, so t h e gears on the ends of the rollers fit int o the appropriate slots.
30 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Setup Loading Cards Loading Cards T o help you load, print, and collect cards, the printer has a card feeder and card output hopper . Card Feeder The card feeder is used for loadin g ca rds, it ca n hold up to 100 cards o f 30 mils th ickness.
Printer Setup Loading Cards P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 31 3. Remove th e cellophane wrapper from the card stack.
32 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Setup Loading Cards Card Output Hopper 1. Raise the printer lid, and pull the output ho pper down to place it in its functio nal position. 2. When not using the prin ter , place the card out put hopper ba ck in its closed position to protect the p rinter from dust.
Printer Setup Printing a T est Card P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 33 Printing a T est Card W ith ribbon ca rtridge and ca rds loaded, your pri nte r is ready to pri nt. T o check the operat ion of the printer , you should print a test card.
34 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Setup T ypical Printer Op eration T ypical Printer Operation The ZXP Series 3 Card Printer c an be used with your soft ware applicatio n program, using t he Drivers on the CD provided with you r Printer; refer to Inst alling the W indows Printer Driv er on page 14 .
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 35 4 Printer Settings and Adjustments Introduction This section describes the setti ngs and adjustments that can be made to your W indows ZXP Series 3 Printer Driver . This consists of two major topic s: Card Printer Properties .
36 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Settings and Adju stment s Card Printer Properties Card Printer Properties T o ac cess the Card Printe r Properties, se lect S tart > Settings > Printers and Faxes .
Printer Settings and Adjustment s Card Printer Properties P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 37 General T ab The General tab shows th e selected printer and lists the features of the printer . T o access the General tab, select S tar t > Settings > Printers an d Faxes .
38 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Settings and Adju stment s Card Printer Properties Sharing T ab On the Sharing tab, you can choose to share t h e printer over the network and install additiona l drivers to accommodat e different operat ing systems.
Printer Settings and Adjustment s Card Printer Properties P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 39 Port s T ab Use the Ports tab to specify the c omputer port to whi ch the printer is connected.
40 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Settings and Adju stment s Card Printer Properties Advanced T ab The Advanced t ab determines the spooling (queuing ) of print jobs and determines ho w spooled jobs are handled re lative to the most recent j ob.
Printer Settings and Adjustment s Card Printer Properties P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 41 Color Management T ab Color Managemen t settings al low you to associ ate color profi les on the printer ba sed on the type of medi a be ing used and printe r co nfiguration.
42 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Settings and Adju stment s Card Printer Properties Security T ab This is the standard W indows security screen, showing user access to various printe r control options. Both Print a nd Manage Printers must be c hecked for full func tionality of the printer .
Printer Settings and Adjustment s Card Printer Properties P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 43 Device Settings T ab The Device Settings tab provides device info rmation, security status, and printer usage. T o access the Device Settings tab, select S t art > Settings > Prin ters and Faxes .
44 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Settings and Adju stment s Card Printer Properties Encoder Settings Dialog box for setting Magnet ic Encoder paramete rs. This feature is not enab led if the printe r does not have the magnetic encoder optio n.
Printer Settings and Adjustment s Card Printer Properties P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 45 ADV ANCED SETTINGS DIALOGUE BOX • Tr a c k : Select the track you want to configure.
46 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Settings and Adju stment s Card Printer Properties T ools Dialog box for testin g and communicating with the printer .
Printer Settings and Adjustment s Card Printer Properties P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 47 F/W Download This Dialog box is used to install the firmware downloa ded from the Zebra web site at http://zebraca rd.com under Drivers & Downloads .
48 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Settings and Adju stment s Card Printer Properties Device Information Printer configuration status window . • Model/Firmwar e V ersio n - Specifies the printer mo de l number and installed firmware version.
Printer Settings and Adjustment s Card Printer Properties P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 49 Single Feed Options Click on the appropri ate radio button to Enable / Disable Si ngle Feed operation. About Dialog Box for spec ifying the Pri nter Model, the Driv er V er sion, and the Copy right.
50 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Settings and Adju stment s Card Printer Prin ting Preferen ces Card Printer Printing Preferences T o access the Card Printer Properties, select S tart > Set tings > Printers and Faxes .
Printer Settings and Adjustment s Card Printer Printing Preferences P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 51 • Color Adjustment - Adjusts color outp ut (Intensity and Contrast). Allows you to adju st th e image colors; these adjustments ap pl y to the enti re card, not just photographic i mage.
52 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Settings and Adju stment s Card Printer Prin ting Preferen ces Ribbon Ty p e - Displays type of ribbon instal led in printer .
Printer Settings and Adjustment s Card Printer Printing Preferences P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 53 • Black Panel - Defines how black panel i s applied in a card design.
54 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Printer Settings and Adju stment s Card Printer Prin ting Preferen ces • Back Overlay V arnish - Feature selectio n for applying an overlay varnish ribb on to the back of a card.
Printer Settings and Adjustment s Card Printer Printing Preferences P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 55 • Head Settings - Setting for heat adjustme nts on the print h ead. Adjustment s can be made to the Contrast and Intensit y .
56 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A.
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 57 5 Cleaning Cleaning the System Y o ur Printer includes a simp le cleaning system u sing Pre-Saturated Cl eaning Cards provid ed.
58 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Cleaning Cleaning the System How to Clean St e p 1 . Place t he printer po wer switch in th e ON ( | ) position, an d then press and ho ld the Multi-Function Control Butto n for 5 seconds.
Cleaning Cleaning the Printhead P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 59 Cleaning the Printhead Use of the cleaning cards will no rmal ly do an adequate job of cleaning the printer . However , a separate Printhead cleaning, using swabs, can remove more stubborn deposits when print anomalies persist.
60 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A.
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 61 6 Troubleshooting Introduction The objective o f troubleshootin g is to relate a problem to an associated assembly or system function, in order to most effici ently isolate an d rep air the problem.
62 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A T roubleshooting T roubleshooting Procedures T roubleshooting Procedures LCD Panel W arnings and Error Messages The following tables show causes and solution s to symptoms relat ed to improper op eration.
T roubleshooting T rou bleshooting Procedure s P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 63 ERROR MESSAGES (printer will not operate) Note: If the problem persists, contact T echnical Support; see W orldwide Support on page 109 .
64 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A T roubleshooting T roubleshooting Procedures Print Quality Issues This section will help you resolv e print qualit y problems. The print quality is depe ndent on several factor s.
T roubleshooting T rou bleshooting Procedure s P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 65 Example • Small sp ots Small spots appear on the printed card with a non-printe d area or a dif ferent color . Possible Cause: • Contamination on the card surface.
66 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A T roubleshooting T roubleshooting Procedures Example • Non-printing horizo ntal lines (white) There are non-printing horizontal li nes (white) on the card surfaces. Possible Cause: • Ribbon cartrid ge is not correctly positioned.
T roubleshooting T rou bleshooting Procedure s P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 67 Example • Pale or inconsistent resu lts Printing shows very pale or inconsistent results. Possible Cause: • Ribbon cartrid ge have been stored improp erly or is damaged.
68 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A T roubleshooting T roubleshooting Procedures Example • Blurry printed image Printing shows bl urry printed image. Possible Cause: • Ribbon cart ridge may not b e correctly positi oned.
T roubleshooting T rou bleshooting Procedure s P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 69 Example • No printing No printing on the card. Possible Cause: • Ribbon c artridge may no t be install ed in the prin ter . Solution: • Check for r ibbon c ar t ri dg e in the printer .
70 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A.
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 71 7 Technical Specifications Printer S pecifications General • Single-sided and dual-side d printing • Single card feed capab.
72 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A T echnical Specif ications Printer S pecifications Ribbon Specifica tions • i Series™ intellig ent media techno logy • YM.
T echnical Specif ications Printer S pecifications P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 73 Environment al • Operating T emperature: 60°F to 86°F (15°C to 30°C) .
74 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A T echnical Specif ications ISO S tandard Card Dim ensions ISO S t andard Card Dimensions Dimensions for Plain Card ISO St andard 7810 Dimensions for Magnetic S tri pe Card ISO St andard 781 1 Cont act Location for Smar t Card ISO St andard 7816 2.
T echnical Specif ications ISO S tandard Car d Dimensions P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 75 Declarations of Conformity For a formal certificate, please contact the Compliance Of fice at Zebra’ s Camarillo facility .
76 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A T echnical Specif ications ISO S tandard Card Dim ensions Jap anese Notification NCC W arning Message.
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 77 Appendix A Network Operations Introduction This section covers: Network Configur ations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Setting Up a Network Prin ter .
78 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Network Operations Network Configurations Printer Sharing In printer sharing, the printer is con nected locally t o the host comput er and configured to be shared to other client computers.
Network Operation s P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 79 Internal Print Server An internal print server is similar to an external print serv er , except the print server is integrated in to the printer . This removes the need for a separate po wer supply and separate device drivers.
80 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Network Operations Setting Up a Network Printer Use this proced ure if you hav e already installe d an et hernet printer on your system (refer to Section 2 ), and you want to install a second ethernet print er on the network via the Microsoft Add Printer Wizard .
Network Operation s P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 81 Step 6. Cli ck on the Next button Step 7. Ob serve the Select a Printer Port window . Step 8. Cli ck on the Cr eate a new port radio button. Step 9. From the dropdown menu, select S tandar d TCP/IP Port .
82 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Network Operations Step 13. Observe a second Add S tandar d TCP/IP Port W izard window . Step 14. Enter the IP Address of yo ur printer . Note that the Port Name will a utomatically be filled in when yo u enter the IP Addres s.
Network Operation s P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 83 Step 18. Observe the Com pleting the Add Standar d TCP/IP Printer Port W izard window . Step 19. Click on th e Finish button, and observe the Install Printer So ftwar e window .
84 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Network Operations Step 22. Observe the Use Existing Driver window . Step 23. Select the Keep existing driver radio button. Step 24. Click the Next button, and observe the Name Y our Printer window .
Network Operation s P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 85 Step 28. Observe the Printer Sharing window . Step 29. Select the appropriate radio but ton in answer to the question Do you want to shar e this printer ...? Enter the Shar e name if applicable.
86 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Network Operations Step 33. Observe the C ompleting the Ad d Printer W izard window . Step 34. Click on th e Finish button to compl ete the Add Printer W izar d . Y ou have successful ly installed the network printer .
Network Operation s P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 87 Printer Pooling Setting Up Printer Pooling Printer Pooling i s a standard feature o f W indows, which l ets you spread the p rinted output across a pool of se veral printers.
88 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Network Operations Using the Printer Pool When the first pr inter has taken as many jobs as it can handle (tha t being two job .
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 89 Appendix B Magnetic Encoder Option Introduction This section contains information on the addi tional operations of the ZXP Series 3 Card Printer with an optional Magne tic Encoder .
90 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Magnetic Encoder Option Driver Settings Encoder Settings The Encoder Settings dialo g box is used for setting various Magnetic Encoder parameters. This feature is not enabled if the prin ter does not ha ve the magnetic encoder option.
Magnetic En coder Option P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 91 Advanced Settings The Advanced Settings dialog b ox is used for primaril y for Non-ISO en coding.
92 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Magnetic Encoder Option Media Loading Orient ation When loading cards with magnetic stripes into the card feeder , please en sure that the magnet ic stripe is facing the left side of the pri nter , and closest to the b ottom edge of the c ard feeder .
Magnetic En coder Option P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 93 Magnetic Encoding T ype ISO (Default) The encoder read s and writes standa rd ISO track data forma ts in standard ISO tr ack locations . The following sh ows the th ree standard ISO tracks.
94 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Magnetic Encoder Option AAMV A The da ta st ored on magneti c stripes on Americ an driver's li censes is spe cified b y th e American Association of Mot or V ehicle Ad ministrators (AA MV A).
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 95 A PPENDIX C Smart Card Options Introduction This Appendix c ontains informatio n on the add itional operation s of a Printer eq.
96 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Smart Card Options Output Hopper The Output Ho pper is positioned on the front of the Prin ter and receives the printed cards. St e p 1 . Install the Output Hopper by inserting the four tabs on the hopper into the four slots on the fron t of the Printe r .
Smart Card Options P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 97 Cont act Smart Cards Contact Smart Cards have a pad of cont acts on the surface of the card that c onnects to the circuitry embedded into the card.
98 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Smart Card Options Cont actless Smart Cards Rather than using a contact pad, Contact less Smart Cards use vario us short-range radio technologie s to “conne ct” to the printer .
Smart Card Options P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 99 Cont act St ation Smart Card Interface When a command to the printer interface sen ds a card to the Smart Card Cont act S tation, the printer connects the Smart Card Conta ct Station t o the female DB-9 c onnector on the rear of the printer .
100 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A.
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 101 Appendix D CardSense TM Single Card Feed Mode Introduction For operating the Z XP Series 3 Card Printer in si ngle card feed mode, the printer requires th at the operator install an optional Ca rdSense Single Card Feed Kit.
102 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A CardSense TM Single Card Feed Mode Inst alling the CardSense Single Card Feed Kit Step 1. T urn printer power OFF . Step 2. Open the lid , and remove the ribbon cartridge. Step 3.
CardSense TM Single Card Feed Mode P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 103 Step 7. Remove the Cleaning Roll er from the Cl eaning Cartridge, and then remove the protective wrapp er from the Cl eaning Roller, Step 8. Place the Cleaning Roll er in the Cartridge, and close the lid.
104 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A CardSense TM Single Card Feed Mode Setting Up the Printer Driver Step 1. Open Printers and Faxes (click S tart > Settings > Printers and Fa xes ). Step 2. Right-click t he printer for which you w ant to change settings, then click Pr operties .
CardSense TM Single Card Feed Mode P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 105 Printing a Single Card Step 1. Cards are inserte d one at a time into the slot on the fr ont of the prin ter . Do not feed more than one card at a time.
106 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A.
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 107 Appendix E Enclosure Lock Option Introduction The Enclosure Lock Option can either be factory-insta lle d or adde d as an upgrade. This option ensu res that only au thorized personne l have physica l access to the print media (ribbon and cards).
108 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A.
P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 109 Appendix F Worldwide Support For T echnical Support or Repair Services, co ntact the appropriate facilit y listed below . North America and Latin Am erica - T echnical Support T : +1 877 ASK ZEBRA (877 275 93 27) +1 847 913 2259 E: ts1@zebra.
1 10 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A Worldwid e Support Europe, Middle East, and Africa - T echni cal Support For further assist ance, cont act: Zebra T echnologi.
Worldwide Support P1032297-001 Rev . A Zebra ZXP Series 3 Card Printer User ’s Manual 1 1 1 Asia Pacific - T echnical Support Zebra T echnologies Asia Pacific Pte. Ltd. 120 Robinson Road #06-01 Par akou Buildin g Singapore 0689 13 T : +6 5 68 58 0722 F: +6 5 6885 0838 E: tsasiapacific@zebra.
1 12 Zebra ZXP Series 3 Card Printer User ’s Manual P1032297-001 Rev . A.
Ein wichtiger Punkt beim Kauf des Geräts Zebra ZXP S3 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Zebra ZXP S3 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Zebra ZXP S3 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Zebra ZXP S3 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Zebra ZXP S3 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Zebra ZXP S3 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Zebra ZXP S3 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Zebra ZXP S3. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Zebra ZXP S3 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
