Benutzeranleitung / Produktwartung P310 des Produzenten Zebra Technologies
Zur Seite of 46
User’s Manual No. 980261-001 Rev. C 2003 ZIH Corp. User’s Guide P310 800-658-8788 www.abcoffice.com abcoffice.
800-658-8788 www.abcoffice.com abcoffice.
FOREWORD This manual contains installation and operation information for the P310 Series card printers man - ufactured by Zebra Technologies Corporation.
PRODUCT WARRANTY STATEMENT All Zebra Card Printers are warranted against defects in material or workmanship for twelve (12) months from the purchase date.
DECLARATIONS OF CONFORMITY European Council Directive Compliance to Standards 89/336/EEC Modified by 92/31/EEC & 93/61/EEC EMC Directive EN 55022-B, CISPR 22 RF Emissions Control EMC Directive EN .
P310 PRINTER MODELS Zebra’s Product Numbers tell the story: Here is a quick review of Zebra’s Card Printer Series numbering and lettering system to help you. Zebra’s P310C Plastic Card Printer Series employ Dye Sublimation and Resin Thermal Transfer technologies.
ICONS Throughout this manual, different icons high - light important information, as follows: Important general information Mechanical hazard, such as one associated with moving parts, capable of resulting in equipment damage or personal injury.
viii 980261-001 Rev.C Table of Contents ICONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi GETTING STARTED . . . . . . . . . . . . . . . . . . . . . 1 UNPACKING YOUR CARD PRINTER . . . . . . . . . . . . . 1 INDICATORS AND CONTROLS . . .
1 GETTING STARTED UNPACKING YOUR CARD PRINTER Your P310 printer ships in a carton and protec- tive anti-static bag. Keep all packing material in case you need to move or re-ship the printer. While unpacking, inspect the carton to ensure that no damage occurred during shipping.
In addition to user documentation, make sure the following items are included with your P310 printer: To reorder, please refer to Appendix C of this manual.
INDICATORS AND CONTROLS Your P310 Printer has three Status indicators and a panel button on the front and a power switch on the rear: INDICATORS (green, amber & red) signal printer activity by illuminating or flashing, as follows: 980261-001 Rev.
PRINTER INSTALLATION The following will guide you through the instal - lation of your P310 Printer. CAUTION: Limit AC power supplied to the P310 to 110 ~ 230 volts, 60 ~ 50 Hertz, for an associated 680 ~ 280 milliamps. Limit excess current draw to 16 amps or less, using an associ - ated circuit breaker or other such device.
2 OPERATION P310 PRINTER FEATURES The following shows the features found on your P310 Printer: 980261-001 Rev.C 5 PLEASE NO TE: Any blue items inside the printer can be operated by the user . ST ANDARD FEA TURES 1. Print Head 2. Print Head Unlock Lever 3.
LOADING RIBBONS The P310 Printer requires approved ribbons (See Appendix C). The Resin Thermal Transfer and Dye Sublimation ribbons are specifically designed for your P310 Printer. For optimum performance and printer life (Print Head), al - ways use approved ribbons.
Please note that the ribbon automatically synchronizes whenever the print head lock down occurs. 980261-001 Rev.C 7 3. L oad ribbon onto the supply spindle (under print head carriage) and empty core (with tape attached) onto the take-up spindle. Make sure the ribbon comes off of the top of the supply spindle and feeds to the top of the take-up 4.
LOADING CARDS To help you load, print, and collect cards, the P310 has with the following items: DO NOT bend cards or touch print surfaces as this can reduce print quality. The surface of the cards must remain clean and dust free. Always store cards in an enclosed container.
980261-001 Rev.C 9 E* C B A D Install Card Output Hopper onto printer by hooking over bottom edge of card exit aperture. Open Cover , and adjust lever to correct position . R epeat for different card thickness. (F actor y setting is for 30mil (0.762mm) card thickness.
FEEDING ONE CARD AT A TIME A Manual Feed Slot is available on the side of the Card Input Hopper for feeding single cards. Cleaning Cards are fed manually throught this slot. The Card Cartridge must be empty for manual card feeding to work properly. REMOVING CARD CARTRIDGE Remove the Card Cartridge prior to packaging the printer for shipment.
PRINTING A TEST CARD With ribbon and cards loaded, your P310 printer is ready to print. To check the operation of the printer you should print a test card. 980261-001 Rev.C 11 1 2 . Place the printer’s power switch in the OFF (0) position .. . While pressing the panel button , switch printer on .
12 980261-001 Rev.C 800-658-8788 www.abcoffice.com abcoffice.
3 PRINTING A SAMPLE CARD Printing with the P310 Printer requires the Win- dows printer driver, the WindCard software, or printer command level programming through the printer interface. The P310 Card Printer can be used with any Windows 95/98 and Windows NT 4.
TO INSTALL THE P310 PRINTER DRIVER INTO WINDOWS 95, USE THE FOL - LOWING STEPS: 1. Start your computer and then Windows. 2 . Insert either the CD ROM or Diskette containg the Windows Driver into the associated drive. 3 . Under Windows click the Start button, Select Settings , then Printers .
3 . Come back to File menu and point Page Setup . 4 . Select Size Tab and in Paper Size choose Card . Then select the orientation: ‘Landscape.’ 5 . Go to Margins Tab , put the top, bottom, left and right margins with 0 values. 6 . Press OK to close Page Setup Window.
16 980261-001 Rev.C 800-658-8788 www.abcoffice.com abcoffice.
4 CLEANING PROTECT YOUR FACTORY WAR - RANTY! The recommended maintenance procedures must be performed to maintain your factory warranty. Other than the recommended cleaning proce- dures described in this manual, allow only Zebra authorized technicians to service the P310 Printer NEVER loosen, tighten, adjust, or bend, etc.
CLEANING SYSTEM Your P310 Printer includes a simple cleaning system using the Pre-saturated Cleaning Cards provided. The regular use of these cards will clean and maintain important parts of your printer: including the Print Head, Transport Rollers, and Magnetic Encoder Station.
CLEANING THE PRINT HEAD A cleaning using the Cleaning Cards usually suf - fices. However, a separate Print Head cleaning using swabs can remove more stubborn deposites when print anomolies persist. To avoid deposits, only use foam-tipped swabs. Never use a sharp object to scrape deposites from the print head.
CARD CLEANING CARTRIDGE Your P310 Printer also has a Card Cleaning Cartridge. This item cleans the cards entering the printer. To ensure print quality, the cleaning roller requires periodic replacements. 20 980261-001 Rev.C WHEN TO MAINT AIN When the amber & red indicators flash.
Although the amber and red indicators will keep flashing until maintenance has been performed, the printer will continue to operate. 980261-001 Rev.C 21 3. Remove Cleaning R oller from Cartridge and discard. 4. Install new Cleaning Roller into Car tridge*.
22 980261-001 Rev.C 800-658-8788 www.abcoffice.com abcoffice.
5 TROUBLESHOOTING The following offers causes or solutions to symptoms related to improper operation. Check this table when experiencing any loss of operation or print quality. Note that the LEDs appear white for ON, dark for OFF, and circled with radial lines for FLASHING.
RED INDICATOR ILLUMINATES Printer alert: Ribbon Print Head Bracket open Card Jam Ribbon Jam Command Error The printer stops working 1. Check Print Head Bracket is closed.
CARDS HAVE ‘SCRATCH LINES’ MISSING PRINTING. Incorrect rolled ribbon Dust Print head There are non-printed horizontal lines (white) on card surfaces. 1. Incorrect position of ribbon. Check rib - bon is properly rolled onto the ribbon core and there are no pleats.
26 980261-001 Rev.C 800-658-8788 www.abcoffice.com abcoffice.
6 TECHNICAL SPECIFICATIONS General • High speed printing, over 140 cards/hour edge to edge in full color (YMCKO) throughput • Small footprint • Easy to use Wind Card Classic utility tool (op- tion) • Windows Drivers for 95 and NT 4.
• True Type fonts available via Windows Driver and WindCard Classic utility tool (option) Cards* • Types PVC, Composite • Card width/length: ISO CR-80 - ISO 7810, 2.125” (54mm) by 3.385” (86mm) • Option: Magnetic Stripe - ISO 7811 • Option: Smart Card - ISO 7816-2 • Card thickness: 10 mil (0.
Ribbons* • Monochrome: 1500 cards/roll • Monochrome colors: black, red, blue, green, sil - ver, gold, white, scratch-off grey • K-resin + O: 800 cards/roll • K-dye + O: 800 cards/roll • YMCK.
Options • RS-232C serial port • Smart Card Contact Station (30 mil cards only) • Magnetic Encoder (30 mil cards only) • Extended Warranty program • Hot Swap Warranty program • Cleaning supplies • Service Manual • WindCard design software Use only Zebra-approved card and ribbon media.
APPENDIX A - MAGNETIC CARD STRIPE ENCODER Operation and maintenance requirements for the P310 Printer with the optional mag - netic card stripe encoder. (See Chapter 2 for location). The magnetic encoder can be set for either high and low coercivity .
The read/write head requires periodic cleaning to maintain error-free encoding Although the amber and red indicators will keep flashing until the cleaning process has been per- formed, the printer will continue to operate.
APPENDIX B - SMART CARD CONTACT STATION This section contains information on the addi - tional operations of the P310 Printers with Smart Card Contact Stations. (See Chapter 2 for location.) INTRODUCTION Smart Cards can have a built-in microcomputer and a battery.
DO NOT position printing over the Smart Card Chip DB-9 PINS SMART CARD CONTACT POINTS DB-9 PINS SMART CARD CONTACT POINTS 1 C1 (Vcc) 6 C6 (Vpp) 2 C2 (Reset) 7 C7 (I/O) 3 C3 (Clock) 8 C8 (RFU) 4 C4 (RFU) 9 (GND when chip is at station) 5 C5 (GND) Refer to the Card Printer Programmer’s Manual for complete programming informa - tion.
APPENDIX C - ACCESSORIES & SUPPLIES Please contact your Zebra-authorized dealer to place an order accessories and supplies RIBBONS The following ribbons are optimized for use in the P310 Printers:.
CARDS The following cards are optimized for use in the P310 Printers: Standard Grade PVC * Part Number Description 104523-101 Card, 10mil (200 pack) 104523-110 Card, 10mil adhesive back (200 pack) 104523-104 Card, 30mil (100 pack) 104523-105 Card, 30mil Low Coercivity Mag.
ACCESSORIES Accessories available for P310 Printers appear below. Always refer to the part number when placing an order. Part Number Description 300055-001 Card Printer Parallel/Serial Inter - face Cable, ft.
World Wide Offices: Zebra Technologies Corporation Card Imaging Division 1001 Flynn Road Camarillo, CA 93012-8706 USA Phone: +1 (805) 579 1800 FAX: +1 (805) 579 1808 e-mail: sales@zebracard.
Ein wichtiger Punkt beim Kauf des Geräts Zebra Technologies P310 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Zebra Technologies P310 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Zebra Technologies P310 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Zebra Technologies P310 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Zebra Technologies P310 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Zebra Technologies P310 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Zebra Technologies P310 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Zebra Technologies P310. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Zebra Technologies P310 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
