Benutzeranleitung / Produktwartung WS-38 des Produzenten Windster
Zur Seite of 27
OPERA TION Please read and save this guide through before using your range hood. Store the guide away in a safe place so that you will know where it is, when you want to refer to it.
Table of Contents Important Safety Instructions ---------------------------- Safety Notes ------------------------------------------------- Tools and Materials Required ----------------------------- A.
Read and Save These Instructions CAUTION - To reduce risk of fire and to properly exhaust air, make sure to properly exhaust air. Be sure to duct air outside- Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces, or garages.
W ARNING - To reduce the risk of injury in the event of a range top grease fire, observe the following: A- with a close- fitting lid, cookie sheet, or metal tray, then turn off the burner. Be careful to prevent burns. If the flames do not go out immediately, SMOTHER FLAMES EVACUATE AND CALL THE FIRE DEPARTMENT.
1. All electrical work must be done in accordance with local and/or national electrical code as applicable for safety. This product must be grounded if your are unfamiliar with methods of installing electrical wiring, secure the services of a qualified electrician.
Drill, electric of ratchet driver, with 3/16" wood bit (for drilling starter holes and 1 ” wood bit (to drill an access holes in the cabinet or kitchen wall for the electric power line) ¼ Plier (for opening electrical knockout).
1. Remove the top electrical knockout, you may plan to bring power to the range hood either through the cabinet or through the wall (Fig.1) 2. Insert a screwdriver into the knockout slot and bend the knockout back and forth. (Fig.2) 3. You may have to use pliers to pull the loosened knockout free.
1. If you want to move the electric range to make room for working on the cabinet turn off the 220 volt power for the electric range at the service entrance. 2. Before moving a gas range, shut off the gas. NOTE: SKIP FOLLOWING STEPS 3A THROUGH 3D IF THE HOOD IS TO BE MOUNTED ON A CABINET WITH .
C. Screw the four 1" wood screws (for mounting the hood) into the exact center of the arrow and into the keyhole mounting slots marked on the cabinet bottom (for flush installations), or marked on the 1” recessed cabinet installation) (Fig.7) Do not turn the mounting screws in all the way.
4. Pick up the inner oil collector. NOTE : Reinstalling Baffle filters. Reverse the steps as removing Baffle filters. For mounting under cabinet 1. After above step H, then continue the following steps. 2. Remove 2 screws on the spacer(s). 3. Remove spacer(s).
2. After using the machine, wipes the machine by neutral detergent in order to keep it clean and maintain the appearance with brightness and sanitation. 3. When the level of dirty oil of the collector reached 4/5 of height, it has to be removed in order to avoid overflowing and pollution.
10 F. Completely finished . A. Remove the pre-mounted 6” round duct opening. B. Put transition plate by first installing on the half round section. (Optional) 4 screws C. Take the rectangular starting collar. (Optional) D. Overlap the rectangular starting collar on the top of transition plate.
11 A. Remove the pre-mounted 6” round duct opening. B. Put transition plate by first installing on the half round section. (Optional) 4 screws C. Use slotted screw driver, (or whatever flat head) to knock out the pre-mounted rear rectangular cap. D.
12 F. Take the pre-mounted rectangular plate. H. Insert appropriate rectangular starting collar (optional) (2 different size) ¼ ¾ ( LxWxH ) 1 1 ¼ ”x3 ¾ ”x3 ( LxWxH ) ⓐ ⓑ⅛ " 1 1 "x3 "x1 " I. Mount rectangular starting collar.
1. Position the hood in place so that : 2. Adjust the hood so the front is flush with the cabinet front. a. The electrical line is routed through the appropriate Knockout opening. This step will have to be accomplished while positioning the hood (Fig.
1. Using metal brackets and screws (included), center hood onto board and install screw. 2. Remove the hood from the board and nail the wood board onto the wall. (Be sure the nail is in the center of the stud) 3. Place the range hood on the board and tighten the screw.
1. Remove stainless Baffle filters. ( Ref.P8-H) 2. Remove screws on wiring case, fish out wires through the knockout. (Fig.12) 3. Mark the electrical connection by fastening all wires to the existing wall wiring according to the their colors. (Black to Black, White to White, Green to Ground) 4.
16 2. : Fan speed selection and fan off. A. : When the main power button is being pressed, by pressing button / / for desired fan speed. - slow speed - medium speed - high speed B. : To turn off the fan, just press the button, or press off the main power button.
Note: Care Instruction : Care Instruction : 17 Range hood should be turn on either before or the same time when cooking begins. After cooking, range hood should be kept on for about 3 more minutes for complete ventilation of cooking odor.
Correction Symptom Fan are not operatable. I lluminating LED light does not work A. Check power source to see if it is normal. A. Disconnect the power source. Hood vibrates. A. Check for damaged vanes. B. Check power inlet plug to see if it is plugged firmly into it's socket.
T . Parts Layout Diagram T. Parts Layout Diagram 19 1 4 3 2 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20.
20 Parts List Parts List Description Hood casing Air chamber Top plate 6” round vent ( ) Motor housing Inner vent (Rear ventilation) Motor (s) Fan (s) Oil tunnel * Spacer (s) * Baffle filter (s) * Handle (s) Oil collector * LED light LED light fixture Control panel Control button LED driver Bracket Wiring partition Vertical ventilation No.
NOTE : Any faults with this unit should only be attended to by a qualified technician. U. Circuit Diagram U. Circuit Diagram 21 Voltage : 110V/60Hz Power consumption : maxi 170W (Motor + LED light) MO.
V. S i z e V. Size 22 15" 11" 5" 9 2 12" 26 2-1/2" 22-7/16" 12” 26° 22-7/16” 2-1/2” 92° 15” 11 ” 5” 8-3/8” 5” 2° 30”(36”)(42”)(48”) 22-7/16” .
What Is Not C overed By These Warranti es: 1) Conditions and damages resulting from any of the following: ? Improper installation, delivery , or ma intena nce. ? A n y repa ir, m odification, a lteration or adjustment not a uthorized by the manufac turer or an auth oriz ed service dea lers.
Def ective Products: A ll produc ts will be inspected, tested, and carefully pac ked by t he m anufac turer before shipping to custome rs. Products tha t ar e damaged during transit can only be exchanged for the sa me product, under the condition t hat the custo mer must get a RMA (Return Merchandise Authorization) from Windster.
2102 N. Seaman Ave., S. El Monte, CA 91733 TEL:(626)350-1015 (626)350-5215 FAX:(626)350-1254 © 2006-2008 Windster Hoods, Inc. Specifications subject to change without notice.
Ein wichtiger Punkt beim Kauf des Geräts Windster WS-38 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Windster WS-38 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Windster WS-38 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Windster WS-38 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Windster WS-38 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Windster WS-38 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Windster WS-38 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Windster WS-38. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Windster WS-38 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
