Benutzeranleitung / Produktwartung SCEOX326 des Produzenten Windsor
Zur Seite of 32
86037040 02/20/09 PRV NO. 980066 MODELS: SCEX326 SCEOX326 10052340 10052310 Read these instructions before using the machine Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehme.
MACHINE DATA LOG/OVERVIEW CUTTER 36V (SCEX) 86037040 12/1 2/06 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: ____________________ ____________________________.
TABLE OF CONTENTS CUTTER 36V (SCEX) 86037040 12/1 2/06 3 Machine Data Log/ Overview . ............................... 2 Table of Co ntents ................................................. 3 HOW TO USE THIS MANUAL How to use this Manual. .............
HOW TO USE THIS MANUAL CUTTER 36V (SCEX) 860370 40 12/1 2/06 1-1 This manual contains the f ollowin g sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
CUTTER 36V (SCEX) 860370 40 12/1 2/06 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors.
HAZARD INTENSITY LEVEL CUTTER 36V (SCEX) 860370 40 12/1 2/06 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY.
SAFETY LABEL LOCATION CUTTER 36V (SCEX) 860370 40 12/1 2/06 2-3 NOTE: These drawings indicate the location of safet y labels on the machine . If at any time the labels becom e illegible, promptly replace them. 2% GRADE WARNING SEE MANUAL CIRCUIT BREAKER DECAL PN 86243610 PRV NO.
TECHNICAL SPECIFICATIONS CUTTER 36V (SCEX) 860370 40 12/1 2/06 3-1 ITEM DIMENSION/CAPACIT Y Nominal power 2160 W Rated Voltage 36 Volt DC Rated Amperage 60 amps Batteries 6 x 6 volt 250-305-335 AH @ 20 Hr rate Scrub Brush Motors 2 x .75 hp (.56 kW ) Vacuum Motor 3 Stage .
TECHNICAL SPECIFICATIONS CUTTER 36V (SCEX) 860370 40 12/1 2/06 3-2 SPECIAL NOTES: The sound pressure level at the operator’s ear was measured to be 75 dBA. This was a nearfield, broad-band measurement taken in a typical industrial environment on a tile floor.
HOW THE MACHINE WORKS CUTTER 36V (SCEX) 8603704 0 12/12/ 06 The Saber Cutter is a battery powered, self- propelled, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes, and then vacuums the soiled water back into the recovery tank.
COMPONENTS CUTTER 36V (SCEX) 860370 40 12/1 2/06 3-4 1 3 6 7 11 12 13 14 15 5 2 10 4 8 9 1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Scrub Head Shrouds 6. Solution Tank 7. Solution Tank Cover 8. Solution Tank Drain Hose 9.
CONTROLS CUTTER 36V (SCEX) 860370 40 12/1 2/06 3-5 14 10 4 1 13 5 2 9 3 6 8 15 7 16 11 12 12.
CONTROLS CUTTER 36V (SCEX) 8603704 0 12/12/ 06 3- 6 1. Key Switch 2. Emergency Shut Off Switch 3. Speed Control Knob 4. Propel Control Lever 5. Reverse Button 6. Brush Switch 7. Actuator Switch 8. Solution Control Knob 9. Vacuum Switch 10. Squeegee Lift Lever 11.
CONTROLS CUTTER 36V (SCEX) 860370 40 12/1 2/06 3-7 7. ACTUATOR SWITCH Adjusts the amount of brush pressure to the floor by raising or lowering the scrub deck. To increase brush pressure , press the bottom of the switch. To decrease brush pressure or rise the scrub deck, press the top of the switch.
CONTROLS CUTTER 36V (SCEX) 860370 40 12/1 2/06 3-8 13. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bar illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged.
MACHINE OPERATION CUTTER 36V (SCEX) 860370 40 12/1 2/06 3-9 PRE-RUN MACHINE INSPECTION Do a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps.
MACHINE OPERATION CUTTER 36V (SCEX) 8603704 0 12/12/ 06 3-10 NORMAL SCRUBBING Plan the scrubbing pattern in advance. The longest track is around the perimeter of the area to be cleaned. For efficient operation, the runs should be the longest possible without turning, stopping, or raising and lowering scrub deck/squeegee.
MACHINE OPERATION CUTTER 36V (SCEX) 860370 40 12/1 2/06 3-11 DOUBLE SCRUB For floors which are heavily soiled or h ave thick accumulations of floor finish may not clean sufficiently with one pass.
MAINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-1 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY 100 HRS 200 HRS Check batteries after cha r ging; add water if necessary * Check pad wear to pre.
MAINTENANCE – SER VICE SCHEDULE AINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-2 1. Batteries 2. Squeegee 3. Aqua Mizer 4. Scrub Brushes 5. Recovery Tank Float Shut-Off 6. Solution Strainer 7. Brush Motor 8. Traction Motor 9. Circuit Breakers 10.
MAINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-3 1. BATTERIES The batteries provide the power to ope rate the machine. The batteries require regul ar maintenance to keep them operating at peak efficiency. The machine batteries will hold their charge for long periods of time, but they can only be charged a certain number of times.
MAINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-4 CHECKING BAT TERY SPECIFIC GRAVITY Use a hydrometer to chec k the battery specific gravity. CHECKING GRAVITY A. Hydrometer B. Battery NOTE: Do not take readings immediately after adding distilled water, if the water and acid are not thoroughly mixed, the readi ng m ay not be accurate.
MAINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-5 5. Replace the battery caps, and leave them in place while charging. 6. Unplug the battery connector from the machi ne. FOR SAFETY: When charging, conn ect the charger to the batteries before conne cting the charger to the AC w all outlet.
MAINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-6 2. SQUEEGEE BLADES The front squeegee blade allows solution to pass through channels in the blade into the squee gee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life.
MAINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4- 7 TO ADJUST SQUEEGEE PITCH 1. Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeege e and drive forward at least 2 feet (60cm.). 2. With the squeegee down, stop the machine.
MAINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-8 4. SCRUB BRUSHES There are four different types of brushes available to cover applications from cle aning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market.
MAINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4- 9 ! WA RNING 6. SOLUTION STRAINER The solution strainer is located in front of the left front wheel. The solution strainer protect s the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris.
MAINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-10 ! WA RNING 8. TRACTION MOTOR Do not use a pressure w asher to clean around the motors. Use tap pressure only . TRACTION MOTO R CARBON BRUSH REPLACEMENT FOR SAFETY: Before leaving or servicing m achine, stop on a level surface, turn off machine and remove key.
MAINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-11 ! WA RNING 11. VACUUM MOTOR (Refer to the Vacuum Group in the parts se ction of manual) Do not use a pressure w asher to clean around the vacuum motors. Use tap pressure onl y. Care must be taken so that water is not directed into v acuum motor air intakes.
MAINTENANCE CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-12 12. ACTUATOR SCRUB DECK REMOVAL/REPLACEMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and set parking brake (If opti on is installed). 1. Remove front cover.
MACHINE TROUBLESHOOTING CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-13 PROBLEM CAUSE SOLUTION Poor or no water pick-up Squeegee out of adjustment Adjust squeegee Debris caught on squeegee Remove debris Wo.
MACHINE TROUBLESHOOTING CUTTER 36V (SCEX) 860370 40 12/1 2/06 4-14 PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty Fill solution tank Solution flow turned off or set.
Ein wichtiger Punkt beim Kauf des Geräts Windsor SCEOX326 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Windsor SCEOX326 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Windsor SCEOX326 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Windsor SCEOX326 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Windsor SCEOX326 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Windsor SCEOX326 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Windsor SCEOX326 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Windsor SCEOX326. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Windsor SCEOX326 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
