Benutzeranleitung / Produktwartung FK350-4 des Produzenten Wilton
Zur Seite of 44
Owner's Manual Cold Saw Models: FK350-2, FK350-2SX, FK350-4, FK350-4SX FK350 FK350-SX WMH TOOL GROUP 2420 Vantage Drive Elgin, Illinois 60124 Part No.
2 Warranty and Service WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughou t the United States can give you quick service.
3 Table of Contents Warranty and Service........................................................................................................... ......................... 2 Table of Contents .........................................................
4 Warnings 1. Read and understand the entire o wner's manual before attempting assembly o r operation. 2. Rea d and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause seri ous injury.
5 23. Give your work undivided attention. Looking a round, carrying on a conversation and “horse-play” are careless acts that can result in seriou s injury. 24. Maintain a balanced stance at all times so that you do not fall into the blade or other moving parts.
6 Introduction The FK350 and FK350-SX are circular saws desi gned to provide a reliable solution to the nee ds of machine shops and prod uction environments that work with steel or iron.
7 FK350 Features FK350 Cold Saw FK350-SX Cold Saw.
8 Features Miter Cutting Head The miter cutting head is the unit that cuts the material and consists of a cast iron base, blade support unit and guard, transmission unit, and motor. The depth of cut is set by adjusting the depth cut stop . The miter cutting head swivels and locks into -45º, 90º, and +4 5º by means of a locking mechanism .
9 Installation Unpacking the machine Do not handle the pac ked machine using slings. To install the machine, first remove the packin g, paying particular attention not to cut any electric wires or hydraulic hose s.
10 Controls Control Panel – FK350 The Control Panel (Figure 4) is located on the front the cabinet stand and consists of the Power and High/Stop/Low switches, described below. Power Switch – The Power switch has two positions, Off and On. High/Stop/Low Switch – This switch control s the blade speed.
11 Operation Before using the machine: Check that safety devises (ex., blade guards) are in position and work perf ectly and that personal safety requirements are complied with. Check the sharpness of the blade and verify coolant flow. FK350 1.
12 Miter Adjustment The adjust the miter position follow the steps below while referring to Figure 10: 1. Move the miter position lock (A) to the right to release. 2. Adjust the head to the desired angle ranging from –45º to +45º by push ing on the back of the motor to the right or left.
13 Maintenance Maintenance Requirements All maintenance must be carried out with the power switched off . Failure to comply may result in serious injury! On completion of maintenance, ensure th at replaced parts and/or any tools used ha ve been removed from the machine before starting it up.
14 Lubrication For long life and trouble free operati on, it is essential that this machine is kept well lubricated. The vice and leadscrew should be oiled daily. Pivot joints and bearings should be greased weekly Check t he gearbox oil level weekly, full level is top of sight glass with head in full up position.
15 Blade Selection When using the FK350 col d saw, it is important to select the correct type of blade for the material to be cut. This section explains the limitations and specific applications of the different types of blades.
16 Blade Structure For non--ferrous metals, it is common to use circular saws with brazed hard metal HM cutting edge, consisting of a disc made of alloy tool steel (71Cr1) on which the shape of the teeth and the seats for the cutting edg es are made of Widia K10.
17 Figure 17 Short swarf material such as bra ss, bronze, aluminum and hard cast iron req uire smaller cutting angles beca use the swarf becomes crushed immediately and the rake a ngle has little effect during the cutting stage.
18 Troubleshooting Troubleshooting – Blade and Cutting Problems Problem Probable Cause Solution Incorrect lubricant/coolant fluid Ensure proper coolant flo w. Material too hard Check the cutting speed, feed speed and air pressure parameters and the type of blade you are using.
19 Troubleshooting – Machine Fault & Operating Problems Problem Probable Cause Solution Electrical power supply Check: the phases; the cables; the plug; the socket. Also check that the motor connections are in place. Transformer Check that the voltages are present both on the in put and output.
20 Head Assembly – FK350 & FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350-201 ............... Head Body ........................................................... ................... ................. 1 2 .............
21 Head Assembly – FK350 & FK350-SX.
22 Power Feed Assembly – FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350SX-701 .......... Spring Bracket A .................................................. ........................ ............ 1 2 ............... FK350SX-702 .
23 Power Feed Assembly – FK350-SX.
24 Stock Stop Assembly Index No. Part No. Description Size Qty 1 ............... FK350-501 ............... Block .................................................................... .............. ...................... 1 2 ............... FK350-502 .
25 Stand Assembly – FK350 Index No. Part No. Description Size Qty 1 ............... FK350-601 ............... Cabinet Stand ...................................................... .................... ................ 1 2 ............... FK350-602 ..
26 Stand Assembly – FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350SX-601 .......... Cabinet Stand ...................................................... ....................... ............. 1 2 ............... FK350SX-602 .
27 Stand Assembly – FK350-SX.
28 Base Assembly – FK350 Index No. Part No. Description Size Qty 1 ............... FK350-101 ............... Base ..................................................................... .............. ...................... 1 2 ............... FK350-102 .
29 Base Assembly – FK350.
30 Base Assembly – FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350-101 ............... Base ..................................................................... .............. ...................... 1 2 ............... FK350-102 .
31 Base Assembly – FK350-SX.
32 Manual Vise Assembly – FK350 Index No. Part No. Description Size Qty 1 ............... FK350-301 ............... Base ..................................................................... .............. ...................... 1 2 ............... FK350-302 .
33 Manual Vise Assembly – FK350.
34 Power Vise Assembly – FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350-301 ............... Base ..................................................................... .............. ...................... 1 2 ..............
35 Power Vise Assembly – FK350-SX File 27.
36 Guard Assembly – FK350 & FK350-SX Index No. Part No. Description Size Qty 1 ............... FK350-401 ............... Guard A ................................................................ ................ .................... 1 2 .........
37 Guard Assembly – FK350, FK350-2SX.
38 In-Feed Table Assembly Index No. Part No. Description Size Qty 1 ............... FK350-701 ............... Bracket ................................................................ ............... ..................... 1 2 ............... FK350-702 .
39 Out-Feed Table 1 ............... FK350-801 ............... Guide Block .......................................................... .................. ............... EA 2 ............... FK350-802 ............... Guide Rail .........................
40 Pneumatic Drawing – FK350-SX Wiring Diagram – FK350.
41 Wiring Diagram – FK350-SX.
42 --NOTES--.
43 --NOTES--.
44 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60124 Phone: 800-274-6848 www.wmhtoolgroup.com.
Ein wichtiger Punkt beim Kauf des Geräts Wilton FK350-4 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Wilton FK350-4 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Wilton FK350-4 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Wilton FK350-4 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Wilton FK350-4 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Wilton FK350-4 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Wilton FK350-4 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Wilton FK350-4. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Wilton FK350-4 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
