Benutzeranleitung / Produktwartung 8300/8500 des Produzenten Wayne-Dalton
Zur Seite of 26
IMPORT ANT NO TICES! The complete Installation Instructions and Owner’ s Manual are available at no charge from: Wayne-Dalton, a Division Of Overhead Door Corporation, P .
Important Safety Instructions DEFINITION OF KEY WORDS USED IN THIS MANUAL: W ARNING W ARNING INDICA TES A POTENTIALL Y HAZARDOUS SITUA TION WHICH; IF NOT AVOIDED , COULD RESUL T IN SEVERE OR FA T AL INJURY . CAUTION: PROPER TY DAMAGE OR INJURY CAN RESUL T FROM FAILURE TO FOLLOW INSTRUCTIONS.
Bottom corner brackets RH/LH (as required) Bottom corner brackets RH/LH (as required) Bottom corner brackets RH/LH (as required) (1) Step plate (Outside) (2) Lift handles & spacers (1) Step plate .
Section Quantity Door Height T ype Of Sections Bottom Lock Intermediate(s) Section T op Int I Int II Int III Int IV Int V Int VI 6 9’0” 18” 18” 18” 18” 18” N/A 18” 9’3” 21” 18”.
Wayne-Dalton dealer . Backroom requirement: Backroom is defined as the distance needed from the opening back into the garage to allow the door to open fully . *NOTE: For door heights from 10’1” to 14’0”, refer to your operator manufacture installation instructions for appropriate depth into room.
6 A. FLAG ANGLES (AS REQUIRED): A1. Quick Install (Q.I.) Flag Angles A2. Fully Adjustable (F .A.) Flag Angles B. JAMB BRACKETS (AS REQUIRED): B1. Quick Install (Q.I.) Jamb Brackets B2. Fully Adjustable (F .A.) Jamb Brackets C. TRACK ROLLERS (AS REQUIRED): C1.
INST ALLA TION Before installing your door , be certain that you have read and followed all of the instruc- tions covered in the pre-installation section of this manual. Failure to do so may result in an improperly installed door . NOTE: Reference TDS 160 for general garage door terminology at www.
NOTE: The bottom jamb bracket is always the shortest bracket, while the center jamb bracket is the next tallest. If three jamb brackets per side are included with your door , you will have received a top jamb bracket, which is the tallest.
graduated end hinges, center hinge(s) and strut (if applicable) are on top of their correspond- ing sections. INST ALLA TION ON TOP SECTION: Place the strut on the top edge of the top section, as shown. Center the strut side to side on the section, as shown.
Strutting Schedule For Model 8300 Aluminum (Brown Colored Doors) Door Heights Section Quantity Door Con- figurations Door Widths 6’0” - 10’0” 12’0” - 16’0” 17’0” - 18’0” 20’.
Strutting Schedule For Model 8500 Aluminum (White, Almond & T aupe Colored Doors) Door Heights Section Quantity Door Configu- rations Door Widths 6’0” - 9’0” 10’0” 12’0” - 14’0.
1/2” Diameter holes 4” (2) Spacers (2) 1/4”-20 x 2-1/2” Carriage bolts Lock section outside Lock section inside Lift handle (2) 1/4”-20 Hex nuts Lift handle Bottom Section Tools Required: Level, Wooden shims (if necessary) 10 Center the bottom section in the door opening.
SECURING WITH 1/4” - 20 X 5/8” SELF-TAPPING SCREWS. THERE SHOULD BE NO GAP BETWEEN THE HINGE LEAFS AND THE SECTIONS. NOTE: Install lock at this time (sold separately).
Now , locate the center of the top section and align the center of the holes in the drawbar op- erator bracket assembly with the top section center line. Align the drawbar operator bracket assembly vertically . NOTE: For retro fit applications, the drawbar operator bracket assembly must be aligned with an existing operator .
T op fixture slide 1/4”-20 Flange hex nut Horizontal track Short stem track roller T op section Short stem track roller T op fixture slide 5/16”-18 Hex nut Horizontal track T op section End Bear.
(1) 5/16” X 2” or (1) 5/16” x 1-5/8” T amper -resistant lag screw Vertical line Mounting surface (17” Minimum) Horizontal line (2) 5/16” x 1-5/8” Lag screws Vertical line (2) 5/16” x 1-5/8” Lag screws † (2) Center bearing brackets spaced 6” to 7” apart from the center of the door .
Equal spacing Center bracket bushing Center bracket T orsion keyed shafts Right hand end bearing bracket Left hand end bearing bracket Torsion Spring Attachment Tools Required: Step Ladder, Ratchet Wrench, 9/16” Socket, 9/16” Wrench 21 NOTE: Refer to Package Contents / Parts Breakdown, to determine which Center Bracket(s) came with your door .
Chalking Torsion Spring(s) Tools Required: Step Ladder, Chalk 23 Draw a chalk line horizontally along the center of the torsion spring coil(s). As the torsion spring is wound, the chalk line will create a spiral. This spiral can be used to count and determine the number of turns that are applied on the torsion spring.
W ARNING W ARNING RAISING DOOR FURTHER C AN RESUL T IN DOOR FALLING AND C AUSE SEVERE OR F A T AL INJURY . Clamp a pair of vice clamps onto the vertical tracks just above the second track roller on one side, and just below the second track roller on the other side.
Perforated angle Sound framing members Horizontal track (3) 5/16” Bolts and nuts Perforated angle bolted using (2) 5/16” x 1-5/8” hex head lag screws to ceiling member and parallel to door 5/16.
Trolley Arm Hookup NOTE: If Wayne-Dalton operator / trolley bracket was installed, follow these directions. Align hole in the door arm with holes in operator bracket tabs, as shown.
Cleaning Y our Garage Door IMPORT ANT : DO NOT USE A PRESSURE WASHER ON YOUR GARAGE DOOR! While factory-applied finishes on garage doors are durable, it is desirable to clean them on a routine basis. Some discoloration of the finish may occur when a door has been exposed to dirt-laden atmosphere for a period of time.
and owner’ s manual. If in question about any of the procedures, do not perform the work. Instead, have it adjusted by a trained door systems technician. 3. Lubrication: The door should open and close smoothly . Ensure the door track rollers are rotating freely when opening and closing the door .
Limited Warranty Models 8300 and 8500 Wayne Dalton, a division of Overhead Door Corporation (“Seller”) warrants to the original purchaser of the Models 8300 and 8500 (“Product”), subject to al.
.
AFTER INST ALLA TION IS COMPLETE, F ASTEN THIS MANUAL NEAR GARAGE DOOR FOR EASY REFERENCE. PLEASE DO NO T RETURN THIS PRODUCT TO THE STORE Thank you for your pur chase. Please Do Not Return This Product T o The Store. Please call 1-866-569-3799 (Press Option 1) and follow the prompts to contact the appropriate customer ser vice agent.
Ein wichtiger Punkt beim Kauf des Geräts Wayne-Dalton 8300/8500 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Wayne-Dalton 8300/8500 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Wayne-Dalton 8300/8500 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Wayne-Dalton 8300/8500 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Wayne-Dalton 8300/8500 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Wayne-Dalton 8300/8500 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Wayne-Dalton 8300/8500 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Wayne-Dalton 8300/8500. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Wayne-Dalton 8300/8500 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
