Benutzeranleitung / Produktwartung VE30 ML-126849 des Produzenten Vulcan-Hart
Zur Seite of 32
A product of VULCAN-HART LOUISVILLE, KY 40201-0696 F35410 (May 2003) - NOTICE - This Manual is prepared for the use o f trained Vu lcan Serv ice Te ch ni ci ans and should not be us ed by those not properly qua li fied.
ELECTRIC BRAISING PAN F35410 (May 2003) Page 2 of 32 TABLE OF CONTENTS G E N E R A L ................................................................................ 3 Installation, Operation and Cleaning ..............................................
ELECTRIC BRAISING PAN F35410 (May 2003) Page 3 of 32 GENERAL INSTA LLA TION, OPERA TION A ND CLEA NI NG Refer to the Ins tallation & Operation Manual f or specif ic inst ructions . INTRODUCTIO N The tilting braising pan (skillet) is a versatile piece of cooking equipment.
ELECTRIC BRAISING PANS - REMO VAL AND REPLACEMENT OF PARTS F35410 (May 2003) Page 4 of 32 SPECIFICA TIONS VOLTS PHASE AMPERAGE PER LINE VE30 VE40 TOTAL KW L1-L3 TOTAL KW L1 L2 L3 208 1 9 43 12 58 58 --- 2 4 01 1 25 01 66 76 7 - - - 208 3 9 25 12 39 39 25 2 4 03 1 22 91 64 64 62 9 4 8 03 1 21 51 62 32 31 5 NOTES: 1.
ELECTRIC BRAISING PANS - REMO VAL AND REPLACEMENT OF PARTS F35410 (May 2003) Page 5 of 32 5. Tilt bottom of control panel outwards and pull down. NOTE : The c ontrol panel should be s upported to rem ove lead wire strain. 6. Remo ve control box f rom contr ol panel.
ELECTRIC BRAISING PANS - REMO VAL AND REPLACEMENT OF PARTS F35410 (May 2003) Page 6 of 32 2. Remove power s upply box cover . 3. Disconnect lead wires then remove the component being replaced . 4. Reverse proc edure to install the r eplacem ent com ponent.
ELECTRIC BRAISING PANS - REMO VAL AND REPLACEMENT OF PARTS F35410 (May 2003) Page 7 of 32 LEFT SIDE VIEW SHOWN TOP VIEW SHOWN 7. Check calibration as out lined under TEMPERATURE CONTRO LLER CALIBRATION. PA N POSITION/DOWN LIMIT SWITCH WA RNING: DI SCONNECT THE ELECTRICAL POW ER TO THE MACHI NE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES.
ELECTRIC BRAISING PANS - REMO VAL AND REPLACEMENT OF PARTS F35410 (May 2003) Page 8 of 32 SIDE VIEW SHOWN D. Align roller arm adaptor wit h the four locking tabs pointing up and position one of the tabs at 0°. NOTE: The 0° position of t he roller arm locking tab is the starting point for alignment only.
ELECTRIC BRAISING PANS - REMO VAL AND REPLACEMENT OF PARTS F35410 (May 2003) Page 9 of 32 7. Reverse procedure from step 5 to complete the installation. 8. Adjust pan position/down limit switch on switch mounting bracket as outlined under PAN POSITION/D OW N LIMIT SW IT CH ADJUSTMENT in SERVICE PRO CEDURES AND ADJUSTMENTS.
ELECTRIC BRAISING PANS - REMO VAL AND REPLACEMENT OF PARTS F35410 (May 2003) Page 10 of 32 5. Rem ove the insulation cover. 6. Loosen lock nut and rem ove threaded probe from pan. 7. Reverse proc edure to install and c heck braising pan for pr oper operation.
ELECTRIC BRAISING PANS - REMO VAL AND REPLACEMENT OF PARTS F35410 (May 2003) Page 11 of 32 VE30 REAR VIEW SHOWN 4. Loosen the strain r elief nut and the hold down clam ps for the m otors' power cable. Pull the cable thru the st rain relief opening and rem ove the cable fr om under neath the clam ps.
ELECTRIC BRAISING PANS - REMO VAL AND REPLACEMENT OF PARTS F35410 (May 2003) Page 12 of 32 8. To ins tall: A. W ith drive key on drive shaf t, install cr ank assem bly and tighten set screw against key . B. W ith drive key on manual c rank shaft, install shaf t extension c oupling and tighten set scr ew against key.
ELECTRIC BRAISING PANS - REMO VAL AND REPLACEMENT OF PARTS F35410 (May 2003) Page 13 of 32 RIGHT SIDE REAR VIEW SHOWN 6. Reverse procedure to install and check for proper operation. HIGH LIM I T THERMO STA T WA RNING: DI SCONNECT THE ELECTRICAL POW ER TO THE MACHI NE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES.
ELECTRIC BRAISING PANS - REMO VAL AND REPLACEMENT OF PARTS F35410 (May 2003) Page 14 of 32 Caution: Do not release w rench w hile locking pin is removed or dama ge to the brais ing pan may occur. A. Slowly release downwards for ce to rem ove spring tension.
ELECTRIC BRAISING PANS - SERVICE PR O CEDURES AND ADJUST MENTS F35410 (May 2003) Page 15 of 32 SERVICE PROCEDURES AND ADJUSTMENTS WA RNING: CERTAIN PRO CEDURES IN THIS SECT ION REQ UIRE ELECTRICAL T EST OR MEASUREMENT S W HILE POW ER IS APPLIED TO THE MACHINE.
ELECTRIC BRAISING PANS - SERVICE PR O CEDURES AND ADJUST MENTS F35410 (May 2003) Page 16 of 32 12. Repeat the average tem peratur e calculation f or up to three attem pts. Allow the pan to cycle at least two times between adjustm ents bef ore perfor m ing the calculation.
ELECTRIC BRAISING PANS - SERVICE PR O CEDURES AND ADJUST MENTS F35410 (May 2003) Page 17 of 32 HEA TING ELEMENT TEST VOLTAG E KW PER ELEMENT AMPS PER ELEMENT OHMS PER ELEMENT 208 4 14.3 13.7 240 4 16.7 13.7 480 4 8.7 55.5 NOTES: 1. Values in the table are nominal.
ELECTRIC BRAISING PANS - SERVICE PR O CEDURES AND ADJUST MENTS F35410 (May 2003) Page 18 of 32 SIDE VIEW SHOWN LEFT SIDE VIEW SHOWN A. I f voltage is present but pan does not raise, ref er to MOTORIZED LIFT OPTION ONLY under TROUBLESHOOTI NG.
ELECTRIC BRAISING PANS - SERVICE PR O CEDURES AND ADJUST MENTS F35410 (May 2003) Page 19 of 32 LEFT SIDE VIEW SHOWN B. Adjust mounting switch bracket up or down (as necessary) to obt ain the rear pan dimension of 2.25" to 2.50". 11. Repeat steps 5 thru 9 to check for proper operation.
ELECTRIC BRAISING PANS - SERVICE PR O CEDURES AND ADJUST MENTS F35410 (May 2003) Page 20 of 32 RIGHT SID E REAR VIEW SHOWN B. I f additional adjustment is necessary, push up on the tip of the swit ch actuator to slightly bend t he actuator around the mating edge of the trigger (cam).
ELECTRIC BRAISI NG PANS - ELECTR ICAL OPERATION F35410 (May 2003) Page 21 of 32 ELECTRICAL OPERATION COMP ONENT FUNCTION BRAI SING PA N CONTROLS Temperature Con troll er . . . Monitors t hermocouple input (type E) and regulates braising pan t emperature.
ELECTRIC BRAISI NG PANS - ELECTR ICAL OPERATION F35410 (May 2003) Page 22 of 32 K 1 U p R e l a y ( 3 P D T ) ...... Supplies power to motorized lift circuit to raise t he pan when 24VAC coil is energized.
ELECTRIC BRAISI NG PANS - ELECTR ICAL OPERATION F35410 (May 2003) Page 23 of 32 SEQUENCE OF OPERA TION Refer to s chem atic diagram AI1376 f or the electric al sequence of operation. Manual pan lift is the standard conf iguration. Heating 1. Conditions.
ELECTRIC BRAISI NG PANS - ELECTR ICAL OPERATION F35410 (May 2003) Page 24 of 32 4. W hen the pan is raised 2.25" to 2.50" at the rear, pan position/down lim it switch contac ts change state. T he N.O contac ts open to rem ove power from K3 heat relay coil; and the N.
ELECTRIC BRAISI NG PANS - ELECTR ICAL OPERATION F35410 (May 2003) Page 25 of 32 SCHEMATIC DIA GRA M.
ELECTRIC BRAISI NG PANS - ELECTR ICAL OPERATION F35410 (May 2003) Page 26 of 32 WIRING DI A GRA MS Heating Element Circuits.
ELECTRIC BRAISI NG PANS - ELECTR ICAL OPERATION F35410 (May 2003) Page 27 of 32 Terminal Blo ck Wiring.
ELECTRIC BRAISING PANS - T ROUBLESHOOTING F35410 (May 2003) Page 28 of 32 TROUBLESHOOTING ELECTRIC HEA TING (M A NUA L LI FT OR M OTORIZED LIFT OPTI ON) SYMPTOMS POSSIBLE CA USES Braising pan does not heat, power on light is lit and heat light is lit .
ELECTRIC BRAISING PANS - T ROUBLESHOOTING F35410 (May 2003) Page 29 of 32 MO TORIZED LIFT OPTI ON ONLY SYM PTO M POSSIBLE CAUSES Pan will not raise. 1. Lid switch open (lid not opened) or m alfunction. 2. 120/24VAC transf orm er inoperative. 3. On/off switch of f or m alf unction.
ELECTRIC BRAISING PANS - T ROUBLESHOOTING F35410 (May 2003) Page 30 of 32 - N O T E S -.
ELECTRIC BRAISING PANS - T ROUBLESHOOTING F35410 (May 2003) Page 31 of 32 - N O T E S -.
ELECTRIC BRAISING PANS - CONDENSED SPARE PART S LIST F35410 (May 2003) Printed in U.S.A. CONDENSED SPARE PARTS LIST VE30 & VE40 BRA ISING PA NS PA RT NUM BER DESCRIPTION NOTES 840115 Contactor 25 .
Ein wichtiger Punkt beim Kauf des Geräts Vulcan-Hart VE30 ML-126849 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Vulcan-Hart VE30 ML-126849 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Vulcan-Hart VE30 ML-126849 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Vulcan-Hart VE30 ML-126849 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Vulcan-Hart VE30 ML-126849 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Vulcan-Hart VE30 ML-126849 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Vulcan-Hart VE30 ML-126849 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Vulcan-Hart VE30 ML-126849. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Vulcan-Hart VE30 ML-126849 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
