Benutzeranleitung / Produktwartung D751ST des Produzenten Vivitek
Zur Seite of 74
.
Copyright This publication, includin g all photographs, illustrati ons and softwa re, is protected under international copyright laws, with all rig hts reserved. Neither this manual, nor any of the material contained h erein, may be reproduced without written consent of the author.
DLP Projector—User’s Manual Important Safety Information Important: It is strongly recommended that you read this sect ion carefully b efore using the projector. These safety and usage instructions will ensure that you enj oy many years of safe use of the pr ojector.
P P P r r r e e e f f f a a a c c c e e e — iii — Projector Installation Notice Place the projector in a horizontal p osition The tilt angle of the projector should not exc eed 15 degrees , no.
DLP Projector—User’s Manual — iv — Cooling notes Air outlet Make sure the air outlet is 50cm clear of any obstructi on to ensure proper cooling. Air outlet location should not be in front of the lens of other projector to avoid causing illusions.
P P P r r r e e e f f f a a a c c c e e e Power Safety Only use the supplied power cord. Do not place anything on the powe r cord. Place the power cord wher e it will not be in the way of foot traffic. Remove the batteries from the remote control whe n storing or not in use for a prolonged period.
DLP Projector—User’s Manual — vi — Table of Contents GETTING STARTED ........................................................................................................................................................... 1 P ACKING C HECKLIST .
P P P r r r e e e f f f a a a c c c e e e — vii — HDMI Q & A .................................................................................................................................................................... 55 SPECIFICATIONS .
DLP Projector—User’s Manual — 1 — G ETTING S TARTED Packing Checklist Carefully unpack the projector and che ck that the following items are included: DLP P ROJECT OR (D755WT/D751ST Series ) I.
DLP Projector—User’s Manual Views of Projector Parts Front-right View 4 5 7 6 1 3 2 8 I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Lamp cover Removes cover to repl ace lamp module 2. IR receiver Receives IR si gnal from remote control 3. Lens Projection Lens 4.
DLP Projector—User’s Manual Top view—On-screen Displa y (OSD) buttons and LEDs 1 6 2 3 4 5 12 7 8 9 10 11 I TEM L ABEL D ESCRIPTION S EE PAGE : 1. MENU Opens and exits OSD me nus 2. Navigates in the OSD Quick Menu – For Keystone 16 3. SOURCE Enter the Source menu 4.
DLP Projector—User’s Manual Rear view 15 16 12 3 4 56 7 89 1 0 17 19 14 13 12 11 18 I TEM L ABEL D ESCRIP TION S EE PAGE : 1. Security bar For security and authorized usag e 2. Kensington lock Secure to permanent object with a Kensi ngton® Lock system 50 3.
DLP Projector—User’s Manual — 5 — I TEM L ABEL D ESCRIP TION S EE PAGE : 16. DISPLAYPORT Connect a DISPLAYPORT CABLE from a DISPLAYPORT device 17. VIDEO Connect the composite cable from a video device 18. HDMI Connect the HDMI cable from a HDMI device 19.
DLP Projector—User’s Manual Bottom view — 6 — 2 47. 0 1 135.51 1 2 2 2 1 1 I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Tilt adjustor Rotate adjuster lever to adjust angl e position 14 2.
DLP Projector—User’s Manual Remote Control Par ts Important: 1. Avoid using the projector with bright fluore scent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the pr ojector.
DLP Projector—User’s Manual — 8 — I TEM L ABEL D ESCRIPTION S EE PAGE : 1. IR transmitter Transmit s signals to projec tor 2. Status LED Lights when the remote control is u sed 3. Laser Press to operate the on-screen pointer 4. Up Up arro w when connected throug h USB to a PC 5.
DLP Projector—User’s Manual — 9 — Remote Control Operating Range The remote control uses infrared transmission to c ontrol the projector. It is not necessary to point the remote directly at the projector.
DLP Projector—User’s Manual — 10 — S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the direction of the arrow. 2. Insert the battery with the positive side facing up.
DLP Projector—User’s Manual Starting and Shutting down t he Project or 1. Connect the power cord to the projector. Connect the other end to a wall outlet. 2. Turn on the connected devices. 3. Ensure the POWER LED displays a solid green. Then press the POWER button of the remote to turn on the projector.
DLP Projector—User’s Manual Setting an Access Password (Secu rity Lock) You can use the four (arrow) buttons to se t a password and prevent unauthorized use of the projector. When enabled, the password must be entered after you power on the pro jector.
DLP Projector—User’s Manual 5. You can use the cursor buttons ▲▼◄► either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five. Press the cursor buttons in any order to set the password.
DLP Projector—User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: The projector t able or stand should be level and sturdy . Position the projector so that it is perpendicular t o the screen.
DLP Projector—User’s Manual Adjusting the Focus and Keystone 1. Use the Image-focus control (on the projector only) to sharpen the projected image 2. Use the KEYSTONE buttons on the remote control to correct image-trapezoid (wider top or bottom) effect.
DLP Projector—User’s Manual — 16 — O N -S CREEN D ISPLAY (OSD) M ENU S ETTINGS OSD Menu Controls The projector has an OSD that lets you ma ke image adjustments and c hange various settings. Navigating the OSD You can use the remote contro l cursor buttons to navigate and make changes to the OSD.
DLP Projector—User’s Manual Setting the OSD Language Set the OSD language to your pr eference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to Settings 1 . Press the cursor ▲▼ button to move to the Advanced 1 menu.
DLP Projector—User’s Manual OSD Menu Overview Use the following illustration to quickly find a se tting or determine the range for a setting. Image Settings 1 Off, On Blank, Red, Green, Blue, White Std.
DLP Projector—User’s Manual Image Menu Attention ! All of display mode parameters when changed will be saved to user mode. Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image Menu . Press the cursor ▲▼ button to move up and down in the Image menu.
DLP Projector—User’s Manual Computer Menu Press the MENU button to open the OSD menu. Press ◄► to move to the Image menu. Press ▲▼ to move to the Computer menu and then press Enter or ► . Press ▲▼ to move up and down in the Computer menu.
DLP Projector—User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press Enter or ► . Press ▼▲ to move up and down in the Advanced menu.
DLP Projector—User’s Manual Color Manager Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Color Manager menu and then press Enter or ► . Press ▼▲ to move up and down in the Color Manager menu.
DLP Projector—User’s Manual Settings 1 Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Settings 1 menu. Press the cursor ▲▼ button to move up and down in the Settings 1 menu. Press ◄► to enter and change values for settings.
DLP Projector—User’s Manual Audio Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press ▼▲ to move to the Audio me nu and then press Enter or ► . Press ▼▲ to move up and down in the Audio menu. I TEM D ESCRIP TION Volume Press the ◄► buttons to enter and adjust the audio volume.
DLP Projector—User’s Manual Advanced 1 Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press ▲▼ to move to the Advanced 1 menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced 1 menu.
DLP Projector—User’s Manual 3D Setting I TEM D ESCRIP TION 3D Press the cursor ◄► button to enter and select different 3D mod e. 3D Sync Invert Press the cursor ◄► button to enter and enable or disable 3D Sync Invert. 3D Format Press the cursor ◄► button to enter and enable or disable different 3D Format.
DLP Projector—User’s Manual Advanced 2 Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 1 menu. Press ▲▼ to move to the Advanced 2 menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced 2 menu.
DLP Projector—User’s Manual Settings 2 Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Settings 2 menu.
DLP Projector—User’s Manual Status Press the cursor ▲▼ button to move up and down in the Settings 2 menu. Select the Status menu and press Enter or ► to enter. I TEM D ESCRIPTION Active Source Display the activated source. Video Information Displays reso lution/video information for RGB source and color sta ndard for Video source.
DLP Projector—User’s Manual Advanced 1 Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press ▲▼ to move to the Advanced 1 menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced 1 menu.
DLP Projector—User’s Manual Lamp Hour Reset Please refer to Resetting the Lamp on page 45 to reset the lamp hour counter. Network I TEM D ESCRIP TION Network State Displays the network connection status. DHCP Press ◄► to turn DHCP On or Off. Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and DNS fields.
DLP Projector—User’s Manual Wired LAN Terminal functionalites Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible.
DLP Projector—User’s Manual LAN RJ45 1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 2. On the PC (Laptop), select Start → Control Panel → Net w ork Connections .
DLP Projector—User’s Manual 3. Right-click on Local Area Connection , and select Properties . 4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP) .
DLP Projector—User’s Manual 6. Click Use the following IP address and fill in the IP address and Subnet mask, th en click OK . 7. Press the Menu button on the projector. 8. Select Settings 2 → Advanced 1 → RS232 → Net work Option 9. After getting into Net work , input the following: DHCP: Off IP Address: 10.
DLP Projector—User’s Manual 12. In the Address bar, input t he IP address: 10. 10. 10. 10. 13. Press (Enter) / ► . The projector is setup for remote managemen t.
DLP Projector—User’s Manual — 37 — C ATEGORY I TEM I NPUT -L ENGTH IP Address 15 IP ID 3 Crestron Control Port 5 Projector Name 10 Location 10 Projector Assigned To 10 DHCP (Enabled) (N/A) IP .
DLP Projector—User’s Manual RS232 by Telnet Function Besides projector connected to RS232 interface with “Hyper-Terminal” communication by dedicated RS232 command control, there is alte rnative RS232 command control way, so called “RS232 by TELNET” for LAN/RJ45 interface.
DLP Projector—User’s Manual Input the command format like the below: telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed) ( ttt.xxx.yyy.zzz : IP-Address of the projector) If Telnet-Connection ready, and us er can have RS232 command inpu t, then “Enter” key pressed, the RS232 command will be workable.
DLP Projector—User’s Manual Select “Turn Windows features on or off” to open Have “Telnet Client” option che cked, then press “OK” button. Specsheet for “RS232 by TELNET” : 1. Telnet: TCP 2. Telnet port: 23 (for more detail, kindly pleas e get contact with the service agent or team) 3.
DLP Projector—User’s Manual Advanced 2 Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press ▲▼ to move to the Advanced 2 menu and then press Enter or ► . Press ▲▼ to move up and down in the Advanced 2 menu.
DLP Projector—User’s Manual Source Filter Press the ENTER button to enter the Source Filter sub menu. I TEM D ESCRIP TION VGA1 Press the ◄► buttons to enter and enable or disable the VGA1 source. VGA2 Press the ◄► buttons to enter and enable o r disable the VGA2 source.
DLP Projector—User’s Manual — 43 — M AINTENANCE AND S ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer.
DLP Projector—User’s Manual 2. Remove the lamp compartment cover. 3. Remove the two screws from the lamp module. 4. Lift the module handle up. 5. Pull firmly on the module handle to remove the lamp module. 6. Reverse steps 1 to 5 to install the new lamp module.
DLP Projector—User’s Manual Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. Press the MENU button to open the OSD menu. 2. Press the cursor ◄► button to move to the Settings 2 menu.
DLP Projector—User’s Manual Cleaning the filter (filter: optional parts) The air filter prevents dust from accumulating on the surface of the optical elements inside the projector. If the filter is dirty or clogged, your projector may overheat or degrading the projected image quality.
DLP Projector—User’s Manual Replacing the Filter 1. Turn off the projector, and unplug the AC power cord from the AC outlet. Clean up the dust on the projector and around the air vents. Pull out the filter cover and remove from the projector Use soft brush gently to clean the filter dust both side.
DLP Projector—User’s Manual Cleaning the Projector Cleaning the projector to remove dust and gr ime will help ensure trouble-free operation. Cleaning the Projector Mirror: 1. Remove dust with a “Bellows/Lens Blower” readily available from Camera shops to pr event scratching the mi rror when subsequently wiped.
DLP Projector—User’s Manual Cleaning the Case Refer to the following to clean the projector case. 1. Wipe off dust with a clean dampened cloth. 2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe the case.
DLP Projector—User’s Manual Using the Physical Lock Using the Kensington ® Lock If you are concerned about security, attach t he projector to a permanent object with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensi ngton security cable.
DLP Projector—User’s Manual — 51 — T ROUBLESHOOTING Common problems and solut i ons These guidelines provide tips to deal with problem s you may encounter while using the projector. If the problem remains unsolved, c ontact your dealer for assistance.
DLP Projector—User’s Manual — 52 — LED Error Messages E RROR C ODE M ES SAGES P OWER L ED G REEN L AMP L ED R ED T EMP L ED R ED System Initial Flashing OFF OFF Ready to Power on (Standby) ON .
DLP Projector—User’s Manual — 53 — Problem: The image is wider at the top or bottom (trapezoid effect) 1. Position the projector so it is as perpendicular to the screen as possible. 2. Use the Keystone button on the remote control to correct the p roblem.
DLP Projector—User’s Manual — 54 — 3. Check the audio cable connection. 4. Test the source audio output with other speakers. 5. Have the projector serviced. Problem: The sound is distorted 1. Check the audio cable connection. 2. Test the source audio output with other speakers.
DLP Projector—User’s Manual — 55 — HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? 1. Recently, HDMI Licensing, LLC announc ed that cable s would be tested as Standard or High-Speed ca bles.
DLP Projector—User’s Manual — 56 — S PECIFICATIONS Specifications Model D755WT Series (WXGA) D751ST Series (XGA) Display type DMD 0.65" WXGA DMD 0.
DLP Projector—User’s Manual — 57 — Specifications Model D755WTi Series (WXGA) Display type DMD 0.65" WXGA Resolution WXGA 1280 x 800 Native Projection distance 336~421mm Projection screen size 16:10 (80”~100”) Projection lens Fix Throw ratio 0.
DLP Projector—User’s Manual Projection Distance vs. Projection Si ze D755WT/D751ST Ser ies D755WTi Ser ies Projection Distance and Size Table D755WT / D755WTi Series WXGA 16:10 Diagonal 80" 87" 97" 100" Distance 282.3+/-20mm 336.
DLP Projector—User’s Manual — 59 — Timing Mode Table The projector can display several resolutions. The following table outlines t he resolutions that can be displayed by the projector. S IGNAL R ESOLUTION H-S YNC ( KH Z ) V-S YNC ( H Z ) C OMPOSIT E S_V IDEO C OMPONENT RGB (A NALOG ) DP/HDMI (D IGITAL ) NTSC － 15.
DLP Projector—User’s Manual — 60 — S IGNAL R ESOLUTION H-S YNC ( KH Z ) V-S YNC ( H Z ) C OMPOSIT E S_V IDEO C OMPONENT RGB (A NALOG ) DP/HDMI (D IGITAL ) 1600 x1200 75.0 60.0 － － ○ ○ 1680 x 1050 64.7 59.9 － － ○ ○ 1680 x 1050 65.
DLP Projector—User’s Manual — 61 — Projector Dimensions ( D755WT / D751ST Series ) 160.0 1 2 2 .5 8 374.51.
DLP Projector—User’s Manual — 62 — Projector Dimensions ( D755WTi Series ) 185.98 122.58 374.51.
DLP Projector—User’s Manual — 63 — R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
DLP Projector—User’s Manual — 64 — A PPENDIX I RS-232C Protocol RS232 Setting Baud rate: 9600 Parity check: None Data bit: 8 Stop bit: 1 Flow Control None Control Command Stru cture Header cod.
DLP Projector—User’s Manual — 65 — Command Group 01 ASCII HEX Function Description Return Value VXXS0105n 56H 39H 39H 53H 30H 31H 30H 35H n 0D H Set Sharpn ess 0~31 P/F VXXG0106 56H 39H 39H 47.
DLP Projector—User’s Manual — 66 — ommand Group 03 ASCII HEX Function Description Return Value VXXS0304n 56H 39H 39H 53H 30H 33H 30H 3 4H n 0DH Freeze On P/F VXXG0305 56H 39H 39H 47H 30H 33H 3.
Ein wichtiger Punkt beim Kauf des Geräts Vivitek D751ST (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Vivitek D751ST noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Vivitek D751ST - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Vivitek D751ST reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Vivitek D751ST erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Vivitek D751ST besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Vivitek D751ST verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Vivitek D751ST. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Vivitek D751ST gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
