Benutzeranleitung / Produktwartung 8412S des Produzenten Vertical Communications
Zur Seite of 132
R DXP, DXP Plus , and FX Series Digital Communications Systems Large Screen Speakerphone Reference Manual MESSAGE * 0 # WXY 9 TUV 8 PRS 7 GHI 4 JKL 5 MNO 6 DEF 3 1 ABC 2 TAP HOLD TRNS/CONF SPEAKER MUT.
Comdial strives to design the features in our comm unications systems to be fully interactive with one another . However , this is not always possible, as the combinations of accessories and features are too varied and extensive to insure total feature compatibility .
Contents 1 Introducing The LCD Speakerphone . . . . . . . . . . . . . 1–1 1.1 Using This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1 1.2 Using Your Speakerphone . . . . . . . . . . . . . . . . . . . . . . . 1–3 1.3 Using Your Headset .
4 Placing Calls On Hold . . . . . . . . . . . . . . . . . . . . . . . . . 4–1 4.1 Holding Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1 4.2 Handling Hold Recalls . . . . . . . . . . . . . . . . . . . . . . . . . . 4–4 4.
7.19 Using Direct Inward System Access (DISA) . . . . . . . . . . . . . . . . . . . . . . . . 7–17 7.20 Using The Tracker Paging System . . . . . . . . . . . . . . . 7–20 7.21 Using E And M Tie Lines . . . . . . . . . . . . . . . . . . . . . . 7–23 7.
This page remains blank intentionally..
Introducing The Large Screen Speakerphone 1.1 Using This Guide This user’s guide describes your large screen speakerphone and tells you how to use it. The sections in this introductory chapter help you become familiar with your speakerphone’s controls and indicators.
Your telephone provides several non-verbal ways to communicate using lights and indicators. The descriptions of these methods are provided in a separate chapter: 8 Sending And Receiving Non-Verbal Messages You can program many of the buttons on your telephone to enhance the unit’s versatility and usability.
1.2 Using Your Speakerphone When using your speakerphone, the microphone and loudspeaker are farther away from you than when you use a handset. Both the signal from the loudspeaker and the signal to the microphone must be strengthened.
Depending on telephone line conditions and the type of speakerphone the distant party is using, it may not be possible for the 8412F speakerphone to operate in full-duplex mode.
1.2.2 Half-Duplex Speakerphone Guidelines NOTE: The speakerphone user guidelines in this section do not apply to the Impact SCS 8412F-** when it is operating in full-duplex mode. However, when the 8412F-** is in half-duplex mode or in “speech training” mode, the following guidelines are applicable.
• To manually place a call using your speakerphone, 1. Press the INTERCOM or line button. 2. Dial the number. 3. When party answers, speak toward the telephone. • To automatically dial a number using your speakerphone, 1. Press the preprogrammed speed dial or DSS button and speak toward the telephone when your party answers.
Large Screen Speakerphone Manual 1 – 7 GCA70–349 Introducing The Large Screen Speakerphone.
1.3 Using Your Headset NOTE: The Comdial Impact SCS-AM and Impact SCS-AB headsets are designed for use with the Impact SCS 8412F-** and 8412S-** speakerphones.
1.4 Understanding The Large Screen Display Your speakerphone has a large screen display consisting of six lines of 24 possible character positions per line. This provides you with much more system information than can be presented on two-line displays.
1.5 Understanding The Display Abbreviations This chart identifies the interactive button abbreviations that appear in your display. Feature Definition Account Code Stores a button that enables account code entry. Answer Answers a call ringing at your station.
Feature Definition Erase Use to delete an incorrect entry when programming a speed dial number. Exit Ends a current programming session. Feature Button Presents several different features you can store at programmable buttons for later use. Forward All Route all of your calls to a different station location.
Feature Definition Pick Up Direct When chosen as a feature, stores a button that allows you to pick up a call ringing your intercom line. Pick Up Group When chosen as a feature, stores a button that allows you to pick up any call ringing in your intercom group.
1.6 Knowing Your Speakerphone’s Functions Your speakerphone provides many versatile features for your use. These features are explained in terms of what they allow you to do. Refer to section 1.5 Understanding What The Lights Mean for information about the lights associated with your telephone’s buttons.
Message-Waiting Light • Indicates that a message awaits pick up Microphone Opening • Allows hands-free operation of speakerphone (speak clearly toward microphone opening) Mute Button • Keeps the.
Transfer/Conference Button • Transfers calls • Sets up conference calls Volume Control • Regulates the volume of the ringer, speaker, handset, headset, background music, and group listening mode 1.7 Understanding What The Lights Mean The lights (LEDs) on your LCD speakerphone indicate the status of lines, features, and intercoms.
Next to a fixed feature or programmable feature button: • Steady red = the feature is on. • Steady off = the feature is off. Next to an intercom button: • Steady green with a quick flash = you are using your intercom. • Fluttering red = an LCD message is set on your telephone for others to receive when calling.
1.8 Adjusting The Telephone Pedestal Your telephone has an adjustable pedestal to allow you to select the most comfortable viewing angle. When you receive the telephone, the pedestal is in its lowest position—flush against the pedestal. • To adjust the pedestal, 1.
This page remains blank intentionally..
Answering Calls NOTE: Throughout this book, all references to fixed buttons are printed in upper case bold type, for example “Press the INTERCOM button.” All references to interactive buttons are printed in upper case bold italic type, for example “Press the OPTIONS button.
• After you have answered an outside call at your station, your LCD will display HOLD , TRANSFER, and CONFERENCE : 1. Press HOLD to place the call on hold at your station, —OR— press TRANSFER to.
2.3 Answering Calls At Monitored Stations Your telephone may have the personal intercom number of another telephone appearing at a button location. You can use the light associated with this button to monitor the status of that telephone, and you can press the button to make a call to that telephone if you wish.
2.4 Answering Night-Transferred Calls The system attendant can transfer incoming calls to a particular station or stations for off-hour ringing. Additionally, the installer can program the system for night-answer zones (up to four) with a loud bell associated with each zone.
2.5 Making A Call Pick-Up The installer often arranges several telephones together in a user group. If your telephone is so arranged, you can answer calls that are ringing at other stations within your particular group. Also, you can answer a call that is ringing at any telephone in the system if you know the telephone’s extension number.
2.6 Responding To A Subdued Off-Hook Voice Announcement Your installer can set your LCD speakerphone to receive a Subdued Off-Hook Voice Announcement (SOHVA). This feature allows an intercom caller to break into your call by making an announcement through your handset receiver.
Making Calls 3.1 Dialing Manually You can manually dial a number over any telephone line you select. Or, if the installer assigned a prime line or the idle line preference feature to your LCD speakerphone, it will automatically select a line for use when you lift the handset.
3.2 Dialing Automatically This feature provides one- or two-button speed dialing using programmable buttons at which you have previously stored numbers. Two levels of number storage are available at each storage location, and you can use one or both levels as needed.
3.3 Using Dial By Name The Dial By Name feature provides an index of names you can search. When you select a name in the index, the system will automatically dial that person’s extension number.
3.4 Redialing A Previously Dialed Number If the last number you have called is busy or is not answering, you can redial it once or initiate automatic redialing.
3.4.2 Using The Automatic Redial Feature If your station has the multiple automatic redial feature enabled, you can place up to 10 numbers in your telephone’s redial queue.
• To interrupt the redialing procedure so that you can scroll through numbers in your redial queue, NOTE: You can only do this if the multiple automatic redial numbers feature is enabled and you currently have more that one number in your redial queue.
3.4.3 Storing Numbers For Redial • To permanently store a number you’ve just dialed, 1. While the number is still ringing, press the MORE button, then press SAVE . 2. Select an unused programmable button location. • To dial the saved number, 1. Press button where you saved the number.
3.5 Using Line Groups Some systems have telephone lines arranged into line groups. These line groups are available at each telephone. Your attendant can tell you how your system is arranged. When line groups are available for your use, you may access them for outside calling instead of pressing a line button to select an individual line for use.
3.6 Waiting For A Line (Queuing) If all the lines in a line group are busy, you can place your telephone in a queue to await an idle line. When you share a line with another telephone and the line is busy, you can place your telephone in a queue to await the idle line.
3.7 Making Intercom Calls You can dial an intercom extension manually from the dial pad or automatically using a direct station select (DSS) button that you have previously programmed. There are two methods for making an intercom call. One causes the called telephone to ring.
3.8 Camping On At A Busy Station And Waiting For An Automatic Callback If you call another station and receive a busy signal or a Do Not Disturb tone, you can press a button that will cause the system to ring your telephone when the station is available.
3.9 Camping On At An Idle Station And Waiting For An Automatic Callback If you call another station and hear ringing but receive no answer, you can press a button that will cause the system to ring your telephone when any activity is initiated at that station.
• To answer a call-waiting tone if you receive one while on a call, 1. Hear short tone burst in receiver. 2. Either place current call on hold or complete call and hang up (waiting call will ring at your telephone).
3.12 Making A Subdued Off-Hook Voice Announcement (SOHVA) You can make a subdued voice announcement to another station that is off-hook and busy on a call if the system is arranged to provide this feature.
Placing Calls On Hold 4.1 Holding Calls You can place a call on hold and retrieve it later. With a regular hold, you can pick up the held call at your telephone or another user can pick the call up at a telephone sharing the held call line.
• To place a call on hold, 1. Press HOLD . • To retrieve a held call, 1. Press line button of the held call (with flashing light), —OR— press TA P .
• To retrieve a held call at another station, 1. Press INTERCOM . 2. Dial #90 . 3. Dial extension number of station holding the call. 4. Answer call. Often, you will have more than one call on hold at your station. If you have line appearance for the call placed on hold, you can retrieve it by pressing the appropriate line button.
4.2 Handling Hold Recalls After a call has been on hold for the period of time (set by the installer of your system), the system will cause four quick hold recall tone bursts to sound at your telephone and the flash rate of the line button becomes faster.
4.3 Parking Calls You can place a call on hold in the system so that it can be answered from any station that does not have a line appearance for the call. You accomplish this by placing the call in one of 90 park orbits, where the call remains until it is answered.
4.4 Handling Park Recalls When a parked call times out of the system, it will return to your telephone in the form of a park recall (you will hear four short tone bursts at 12-second intervals). Your LCD will indicate that the call is a park recall and will identify the orbit from which the recall originated.
Transferring Calls 5.1 Transferring Calls—Screened You can answer a call at your LCD speakerphone and transfer it to another telephone. If you first identify the caller to the party receiving the transfer (giving that user the opportunity to prepare for the call), you have made a screened transfer .
• If the intercom party is busy, take one of the following steps (if made available at your telephone by installer programming): 1. Press RECONNECT to reconnect the call to your station. 2. Press SOHVA to interrupt the call and tell the intercom party that a call awaits.
5.2 Transferring Calls—Unscreened You can answer a call at your LCD speakerphone and transfer it to another telephone. If you transfer the call without first announcing it, you have made an unscreened transfer.
5.3 Making A Hot Transfer A hot transfer is a type of screened transfer. To perform a hot transfer, you voice announce the transfer over the speaker of the telephone that you want to receive the transfer, and release the call to that telephone.
5.4 Transferring Calls Using Quick Transfer When the quick transfer method has been programmed by the installer, it allows you to do an automatic screened or unscreened transfer of an incoming line call without pressing the TRANSFER/CONFERENCE button.
This page remains blank intentionally..
Conferencing Calls 6.1 Conferencing Telephones Together When you join your LCD speakerphone together with several other telephones on the same call, the result is called conferencing.
• To retrieve a line from hold and bring that party back into the conference, 1. Press TRANSFER/CONFERENCE . 2. Press line button. 3. Press TRANSFER/CONFERENCE . NOTE: If all the conference circuits are busy, you will not be able to add a party to the conference.
Using The Other Telephone Features 7.1 Adjusting The Display Contrast You can adjust the contrast of the display to darken or lighten it for best viewing.
• To un-block voice-announced calls, 1. Press OPTIONS , then press PROGRAMMING . 2. Set voice announce block to OFF by pressing the VOICE ANNOUNCE BLOCK button (located right of the LCD).
7.4 Displaying Button Functions (Button Query) You can cause the display to identify the function of each button on your telephone. This is useful when the installer has assigned your programmable buttons for special-purpose tasks and you need to remind yourself of the button’s feature.
7.6 Entering Account Codes If the installer has arranged your system for account code entry*, your display may prompt you to enter an account code before dialing or after answering a call. Depending on how the installer programmed your system, these account codes may be “forced”(mandatory) for dialing outside numbers.
7.7 Entering Authorization Codes Authorization codes give you a walking class of service option. Walking class of service provides you with the mobility to use your class of service (COS) features, prime line assignments, and exception numbers on any telephone in the system.
• To unlock your telephone, 1. Press LOCK . 2. Dial your authorization code (remember, include any pauses that you inserted when you locked your telephone). NOTE: When a telephone is locked, it is totally disabled. Not even 911 calls will go through.
7.9 Listening To A Call Over The Telephone Speaker (Group Listening) You can turn on the speaker in your LCD speakerphone while you have the handset lifted if you wish. The distant party’s voice then sounds over the speaker as well as over the handset; however, only your handset microphone is active.
7.10 Making A Call Non-Private (Privacy Release) It is often the case that telephones will share line appearance for one or more lines. When a person in the group uses a line for which others have the same line appearance, the system keeps the call private (others cannot join the conversation by pressing the line button of the line being used).
7.11 Monitoring A Conversation Between Two Telephones (Service Observing) If your LCD speakerphone provides the installer–programmed service observing feature, you can use it to monitor a conversation or activity at another telephone in an undetected manner.
7.12 Muting Your Telephone By using the MUTE button, you can block transmission of your voice to the distant party. You can do this whether you are using the handset or the speaker. For example, if someone comes into your office to talk to you and you do not want this conversation to interrupt the distant party, press the MUTE button.
• To send a paging announcement, 1. Lift handset. 2. Press INTERCOM , then dial 70–77 for zones 1–8 (in the default mode, zone 1 (code 70) provides an all-call function), —OR— press a preprogrammed PAGE button. 3. Make announcement. 4. Remain on line if awaiting a reply (known as a meet-me page), —OR— hang up handset.
7.14 Setting A Do Not Disturb Condition At Your Station This feature keeps calls from ringing at your LCD speakerphone and makes your station appear to be busy to intercom calls. If your installer has programmed your station to have this feature, you can enable it as needed.
7.15 Setting The Volume Control The volume control on your telephone is a multipurpose control you can use to set the volume (loudness) of the ringer, the speaker, the handset, the headset, background music, and the group listening mode.
• There are eight speaker loudness levels. Set these levels for the current call as follows: 1. While on a call and in speakerphone mode, press the VOLUME UP or VOLUME DOWN button once for each change in loudness you desire. 2. To make the current speaker setting the default setting, press SAVE .
• There are eight background music loudness levels. To set the level, 1. While background music is on at your station, press VOLUME UP or VOLUME DOWN button once for each change in loudness you desire. This level will remain set for background music until you change it again, even if you turn off the feature and then reactivate it.
7.17 Switching The Dialing Mode Between Pulse And Tone If the telephone service in your locality is pulse (rotary dialing), the installer arranges your telephone to dial in this manner. If you need to send tones during a dialing sequence (for example, to send bank-by-telephone tones), you can convert to tone dialing mode while dialing.
7.19 Using Direct Inward System Access (DISA) This feature allows you to call into the digital communications system from an external telephone. You can call directly to intercom extensions and talk to the intercom parties or, if the system includes a voice mail option, leave messages for them if they are not available.
fraudulent access or use, or unaccounted-for access or use, and therefore Comdial disclaims any and all liability, and makes no warranty, express or implied, relating to unauthorized or fraudulent access or use, or unaccounted-for access or use. • To make a DISA call to an intercom number, 1.
System Features Available To DISA Callers Default Dialing Code Account code entry S 04 Automatic route selection access 9 Call waiting on busy S 6 Do not disturb override S 03 Intercom dialing/call an.
7.20 Using The Tracker Paging System The Tracker Paging System option allows you to send call back and parked call messages to Tracker pagers assigned to station extension numbers. Along with the parked call message, the system parks the call in orbit for retrieval by the paged party.
• To track a called party without first calling them, 1. Press INTERCOM and dial S 8 . 2. Dial extension number. —OR— Press the LIST NAMES button (to the left of the LCD). The display shows several letters beside each interactive button. Press the button next to the letter of the person’ s name whom you wish to call.
• To retrieve a call that you parked using the Tracker option, 1. Press HOLD button to scroll your held calls, (display shows Page and extension number of each parked call). 2. Press TAP to retrieve the displayed parked call. • If you receive a parked call message on your Tracker pager, 1.
7.21 Using E and M Tie Lines E & M tie line operation is typically used in applications where one group of users often need to call parties located in one or more remote locations. In these applications, your system is directly tied to another similar system at the remote site(s).
NOTE: After transferring the call to the remote end of the E & M tie line, you will have created an unattended conference, and your telephone will appear as though it were on hold.
• To drop out of a conference call between you and two outside lines (creating an unsupervised conference), 1. Hand up (lines remain lighted and in use until one or both outside parties disconnect). • To rejoin an unsupervised conference between two outside lines, 1.
• To deactivate CFOS, 1. Press CFOS interactive button. —OR— Press CFOS preprogrammed button. —OR— Press INTERCOM and dial #5 . • To join an active CFOS call from the CFOS-enabled station, 1. Note flashing HOLD light indicating active CFOS call, and press TAP .
7.23 Mark Problem Line Your programmer can arrange the system so that you can mark a line that is not functioning properly. You do this by pressing a preprogrammed MARK button or by dialing a feature code of your choice.
7.24 Automatic Set Relocation If your installer has equipped your system with automatic set relocation, when you move your telephone to a new location, the system will give you a choice (through a display prompt) as to whether you want to keep your previous programming or use the programming in the new location.
7.25 Using The IMIST Module Impact SCS 8412F-**, and 8412S-** speakerphones equipped with the optional IMIST module can support an IST device (modem, FAX machine, industry-standard telephone, etc.) in addition to the LCD speakerphone. Depending on system programming, the IST device may be used to make outgoing calls and receive incoming calls.
7.26 Using The Caller ID Feature The Caller ID feature allows you to view incoming call numbers before you answer them. Incoming call numbers flash in the lower half of the LCD. If you answer the call, the number appears in the upper half of the LCD. The system also stores numbers that ring on your line but receive no answer.
7.27 Viewing The Call Log The Call Log feature allows you to view the last 10 outgoing calls made from your station. If you have caller ID, the LCD will also display incoming calls. Incoming calls are designated with an I next to the number and outgoing calls are designated with an O .
This page remains blank intentionally..
Sending And Receiving Non-Verbal Messages 8.1 Message Waiting Light And Messaging If the system installer designates your LCD speakerphone as a central message desk or programs it to have message-wait originate ability, you can turn on the message-waiting light of any other telephone.
• To turn off the message waiting light at a busy or idle station, 1. Press INTERCOM . 2. Dial # 3 . 3. Dial extension number of station that was alerted. The message-waiting light of called station will turn off. • To turn off the message-waiting light during message-delivering conversation, 1.
8.2 Sending LCD Messages You can set system-supplied messages at your station to be received and displayed by a calling LCD speakerphone. These messages give the caller information on your telephone status. Get a list of the available messages from the attendant and write them on the blank chart on the next page.
Dialing Code Table Character Dialing Code Character Dialing Code 10 1 80 8 20 2 90 9 30 3 00 0 4 04 space 12 50 5 –1 5 60 6 : 2 9 70 7 8 – 4 Large Screen Speakerphone Manual Sending And Receiving .
8.3 Sending Response Messages By programming one or more RESPONSE MESSAGE buttons on your LCD speakerphone, you can respond with a variety of messages to many calling situations.
• To send an LCD message to a caller who has initiated a SOHVA or intercom call from another LCD telephone, 1. Hear the SOHVA tone or voice announcement.
Programming Your Telephone 9.1 Programming For Speed Dialing Speed dialing is a feature that lets you: • store and dial lengthy numbers using one or two buttons, • store and dial intercom numbers of frequently called telephones, • store frequently used feature codes.
Speed Dial Numbers (Programmable Buttons) 17 28 39 41 0 51 1 61 2 Personal Speed Dial Numbers (Keypad Buttons) 16 27 38 49 51 0 9 – 2 Large Screen Speakerphone Manual Programming Your Telephone GCA7.
9.2 Storing Speed Dial Numbers • To store an outside number as a speed dial number, follow the display prompts and proceed as follows: NOTE: Programming overwrites existing speed dial numbers at button locations. 1. Press OPTIONS , then press PROGRAMMING .
9.3 Storing DSS Numbers • To store an intercom number as a DSS number, NOTE: Storing DSS numbers at button locations will overwrite any previously stored numbers. 1. Press OPTIONS , then press PROGRAMMING . 2. Press NEXT until the DSS option appears.
9.4 Using The Feature Buttons You can create feature access buttons to make telephone operation easier. To do this, use the interactive buttons to select the feature you want to store, and then store it on a programmable button (see the instructions on the next page).
• To create a feature access button, 1. Press OPTIONS , then press PROGRAMMING . 2. Press NEXT until the FEATURE BUTTON option appears. 3. Press FEATURE BUTTON . 4. Select the Feature Level (1 or 2) by pressing the FEATURE LEVEL button to the right of the LCD.
9.5 Storing A Response Message Button A fixed RESPONSE MESSAGE button allows you to send an LCD message to a caller who has initiated a SOHVA or intercom call from another LCD telephone, or to send an LCD message to another LCD telephone that you call and receive a busy signal or no answer.
9.6 Storing Access Codes You can store feature access codes at programmable buttons to provide yourself with one-button access to features that you use quite often. To find your feature codes of interest, turn to the Quick Reference Guide that is located at the end of this publication.
9.7 Setting A Reminder Alert You can set up to two reminder alerts to sound at your LCD speakerphone so that you will remember important regular events (a daily 10:00 meeting or a daily conference call, for example) or occasional events (classroom training, appointments, etc.
This page remains blank intentionally..
Using The Attendant Features 10.1 Using The Special Attendant Buttons In addition to the many feature buttons the system can make available to any station, the DXP provides the attendant position with several special-purpose feature buttons to enhance call processing.
• To forward all calls to an alternate attendant, 1. Press the installer-programmed ALTERNATE button. If an alternate attendant is programmed, the light next to the ALTERNATE button will illuminate and the LCD will indicate the location of the alternate attendant.
• To determine how many calls are queued at the attendant position and awaiting service (on hold, parked, or ringing), 1. Press the installer-programmed QUEUE button. The display will indicate how many calls are in the ring queue and the hold queue, respectively.
10.2 Viewing The System Status Log The system status log gives you information about the status of your system. Status log entries include: system reset, parity (port number), (port number) removed, manual reset, and software reset. Your installer must program a SYSTEM STATUS button on your telephone to provide you with access to the log display.
• To view the log, 1. Press the SYSTEM STATUS button (the button flashes red when the log contains entries). 2. Press the SYSTEM interactive button to display the most recent system status log entry, —OR— press T1 interactive button to display the most recent T1 log entry .
10.3 Operating Your Telephone With A DSS/BLF Console The IB48X, and IB24X DSS/BLF consoles have additional buttons and status lights that extend the memory button capability of an adjacent companion telephone.
10.3.1 Accessing The Button Levels The IB24X and IB48X DSS/BLF consoles have four levels of buttons, quadrupling the consoles’ button capacity. The four buttons at the bottom of each console allow you to select which button level is currently active.
This page remains blank intentionally..
Troubleshooting Your Telephone Symptom Possible Cause INTERCOM light flashing. Your messaging is set. Press INTERCOM, then dial # 02 and hang up. MUTE light on. MUTE is activated. To cancel, press MUTE. SPEAKER light on steady. Background music feature activated even though the system does not provide background music.
This page remains blank intentionally..
Index A Access Codes, Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9–8 Account Codes, Entering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–4 Adjusting The Display Contrast . . . . . . . .
Calls, Answering Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2 Calls, Answering Night Transferred . . . . . . . . . . . . . . . . . . . . . . . . . 2–4 Calls, Answering Outside . . . . . . . . . . . . . . . . . . . .
E E and M Tie Lines, Using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–23 Entering Account Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7–4 Entering Authorization Codes . . . . . . . . . . . . . .
L Large Screen Display, Understanding The . . . . . . . . . . . . . . . . . . . . 1–9 Last Number Redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–4 LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P Paging, Sending An Announcement . . . . . . . . . . . . . . . . . . . . . . . . 7–10 Park Recalls, Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–6 Parking Calls . . . . . . . . . . . . . . . . . . . . . . . . .
Sending LCD Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–3 Sending Response Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–5 Service Observing . . . . . . . . . . . . . . . . . . . . . . .
Transferring Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1 Transferring Calls—Screened . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–1 Transferring Calls—Unscreened . . . . . . . . . . .
This page remains blank intentionally..
Appendix A Quick Reference Guide This chart provides you with a Quick Reference Guide of the feature dialing codes. If you wish, you can detach these pages and keep them near your telephone to serve as a stand alone reference.
Feature Enable Code Disable Code Button Mnemonic Call Forward, Ring-No Answer, All Calls INTERCOM S 54 + extension number INTERCOM # 5 FWDRA Call Forward, Ring-No Answer, Personal Calls INTERCOM S 53 .
Feature Enable Code Disable Code Button Mnemonic Line Group 1 INTERCOM 9 LNG01 Line Groups 2-11 INTERCOM 80-89 LNG02-11 Line Groups 12-16 INTERCOM 60-64 LNG 12-16 Line Pick Up From Any Station, Zones .
Feature Enable Code Disable Code Button Mnemonic Personal Ringing Tones INTERCOM SS 4 + tone code (1-8) Redial Last Dialed Number # Remote Station Disable INTERCOM S 05 + extension number INTERCOM S 0.
NOTE: The dialing codes provided in this quick reference guide are default values. Your system installer has the ability to renumber these codes. The following table details several unique dialing codes that are only applicable to single line proprietary and industry-standard telephones.
NOTES.
This manual has been developed by Comdial Corporation (the “Company”) and is intended for the use of its customers and service personnel. The information in this manual is subject to change without notice.
Charlottesville, V irginia 22901-2829 R World Wide W eb: http://www .comdial.com/ Printed in U.S.A. GCA70–349.02 2/98.
Ein wichtiger Punkt beim Kauf des Geräts Vertical Communications 8412S (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Vertical Communications 8412S noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Vertical Communications 8412S - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Vertical Communications 8412S reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Vertical Communications 8412S erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Vertical Communications 8412S besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Vertical Communications 8412S verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Vertical Communications 8412S. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Vertical Communications 8412S gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
