Benutzeranleitung / Produktwartung XDECT R035 des Produzenten Uniden
Zur Seite of 48
For more exciting new products please visit our website: Australia: www.uniden.com.au New Zealand: www.uniden.co.nz XDECT R035 Bluetooth ®.
.
XDECT R035BT base with answering system and cordless handset Battery cover XDECT R003BT accessory handset and charger (with stand) If you purchased model number: You should have: XDECT R035BT None XDE.
IMPORTANT SAFETY INSTRUCTIONS! When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: This unit is NOT waterproof. DO NOT expose this unit to rain or moisture.
1 CAUTION! Risk of explosion if battery is replaced by an incorrect type! Dispose of used batteries according to the instructions. Do not open or mutilate the battery. Disconnect the battery before shipping this product. For more details, see the Important Information section.
2 Connect the telephone cord Connect the TEL LINE jack to a standard telephone wall jack. Test the connecon Pick up the handset from the cradle and press 1.
3 Visit our website for more information on compatible models. If you are not certain of the profiles supported by your Bluetooth x phone or if you have difficulty pairing your phone to the XDECT R035BT, see the manual that came with your phone. With the MobileLink feature, you can essentially treat your cellular x phone as a second line.
4 Most cellular phones automatically transfer the audio to a x Bluetooth device as soon as it pairs; if yours does not, look in your phone's Bluetooth setup for a "transfer audio" or "send audio to device" option. To test the connecon Pick up the handset from the cradle.
5 Installing the Repeater/Charger(s) (if included) Connect the repeater/charger power cord 1. If your phone came with any accessory handsets and chargers, connect a charger AC adapter to each charger's DC IN 9V jack and set the plug into the notch as shown.
6 Using the Repeater How it works An XDECT R003BT repeater can extend the range of your base in all directions, including up and down. The XDECT R003BT repeater unit is also a charger for the accessory handset.
7 Repeaters can be up to 3 chain-links (maximum) from the base Example of coverage area with 6 repeaters (maximum total) You can roam anywhere within range of the base or the repeater(s) and make and receive calls as usual from your handsets.
8 Picking the best spot The best spot for the repeater is as far from the base as possible while still maintaining a good signal, or near the edge of the base’s coverage area. To find the edge of the coverage area: Stand near the base 1. and make a call on the handset.
9 UNDERSTANDING YOUR PHONE Parts of the base MESSAGE COUNTER UP REV DOWN FWD FIND Charging contacts DELETE PLA Y/ STOP DO NOT DISTURB ON/OFF BLUETOOTH CELLLINK Base k eys and how they work Key name (and icon) What it does FIND In standby: page all handsets to find a lost - one.
10 Key name (and icon) What it does PLAY/STOP ( ) In standby: start playing messages. - While a message is playing: stop playing - messages. While the phone is ringing: mute the - ringer for this call only. FWD ( ) While a message is playing: skip to the - next message.
11 Parts of the handset Microphone Twelve- key dial pad Visual ringer Display Charging contacts Earpiece UP PHONEBOOK/ LEFT SPEAKER DOWN CID/RIGHT REDIAL/ PAUSE MESSAGES/ MUTE CLEAR/ INTERCOM LINK END TALK/ FLASH MENU/ SELECT Handset keys and how they work Key name (and icon) What it does UP ( ) In standby: increase the ringer volume.
12 Key name (and icon) What it does * / LOCK( ) In standby: press and hold to lock or - unlock the keypad. DOWN ( ) In standby: decrease the ringer volume. - During a call: decrease the call volume. - In the menu or any list: move the cursor - down one line.
13 Key name (and icon) What it does REDIAL/PAUSE In standby: open the redial list. - While entering a phone number: insert a - 2-second pause. LINK ( ) In standby: start a telephone call using - your paired Bluetooth phone. While the Bluetooth phone is ringing: - answer the incoming call.
14 Icon What it means T-coil mode is on (see page 34). The battery is 1) empty, 2) getting low, 3) half charged, or 4) fully charged. The signal from the base is 1) weak, 2) low, 3) strong, or 4) very strong. [Aa] The handset enters capital letters first (see page 16).
15 If you open the menu during a call, use x PHONEBOOK/LEFT to back out of the menu without hanging up. If you don't press any keys for 30 seconds, the handset exits the x menu. The Handset Setup Menu You can change these settings separately for each handset.
16 the number keypad to enter 2 digits for the hour and 2 digits for the minutes, e.g., 0530 for 5:30). The Global Setup menu The settings on this menu affect all handsets and the base. Before changing these settings, make sure the phone is in standby and all handsets are within range of the base.
17 USING YOUR PHONE You can control the features in this section through the handset. Learning the Basics To... From the land line From the cell phone make a call: Dial the number, then Press TALK/FLASH or SPEAKER Press LINK twice.* answer a call Press TALK/FLASH or SPEAKER .
18 Change the volume Speaker and earpiece volume Ringer volume You can change the volume of - the speaker on the base and each cordless handset separately. You can change the volume of the - earpiece on each handset; this does not affect the handset’s speaker volume.
19 For New Zealand Model: Press TALK/FLASH on the handset to accept the waiting call. The first caller is put on hold, and you will hear the new caller after a short pause.
20 To… Follow these steps… Open the CID list Press CID/RIGHT . Open the Redial list Press REDIAL/PAUSE. Scroll through the list Press DOWN to scroll through the list from newest to oldest. Press UP to scroll from oldest to newest. Dial a number Highlight the number you want and press TALK/FLASH (or LINK twice*).
21 To do this... Do this... Open/close the phonebook Press PHONEBOOK/LEFT . Scroll through the entries Press DOWN to scroll through the phonebook from A to Z or Up to scroll from Z to A. Jump to entries that start with a certain letter Press the number key corresponding to the letter you want to jump to.
22 Finding a Lost Handset With the phone in standby, press FIND on the base. All the handsets will beep for 1 minute; to end the page, press FIND again or press any key on any handset. Using Mul-Handset Features To use the features in this section, you must have at least two cordless handsets.
23 As long you have privacy mode on, no other handsets can interrupt your call. To allow another handset to join the call, press MENU/SELECT twice to turn privacy mode off.
24 To... Follow these steps: make an intercom page Press CLEAR/INTERCOM , then select the handset you want to talk with (select All to page all handsets at the same time). cancel a page Press END . answer an intercom page Press CLEAR/INTERCOM or TALK/FLASH .
25 number. Press MENU/SELECT to transmit the code. Or, if you change your mind, use PHONEBOOK/LEFT to close the phonebook. Voice message nocaon This feature supports Frequency-Shift Keying (FSK) message x notification. Contact your voice mail provider for more details.
26 Record Time Set the amount of time callers have to leave a message, either 1 minute or 4 minutes. Choose Announce Only if you don’t want the system to let callers to leave a message. Message Alert Have the system beep every 15 seconds when you have a new message; the beeping stops when you listen to all your new messages.
27 You can press the number key next to the commands instead of x scrolling through them. If you don't press any keys for 30 seconds, the phone returns to x standby. Only one handset can access the system at a time, and you can't x access the system while another handset is on a land line or MobileLink call.
28 Geng Your Messages To… From the base From a handset (remote operation) play new messages Press PLAY/STOP . Press MESSAGES/ MUTE . The system announces the number of new and old messages, then plays each new message (followed by the time and date) in the order it was received.
29 Screening Your Calls Another feature your answering system gives you is call screening. While the system is taking a message, you can hear the caller on the base speaker (if you turn on Call Screen) or from a handset. Only one handset at a time can screen calls.
30 If your answering system is off, it will answer after about 15 x rings and sound a series of beeps instead of your greeting. During the greeting (or beeps), press 2. # and immediately enter your security code. (If you enter it incorrectly 3 times, the system hangs up and returns to standby.
31 IMPORTANT INFORMATION Solving Problems If you have any trouble with your phone, try these simple steps first. If you need help, visit the Customer Support page on our website; www. uniden.com.au for Australia or www.uniden.co.nz for New Zealand. If… Try… No handsets can make or receive calls.
32 If… Try… The system won’t record messages. Making sure the Record Time is not set to - Announce Only. Deleting messages (memory may be full). - Making sure the call was on the land line - (the system cannot answer MobileLink calls). A handset can’t access the answering system.
33 If… Try… I can’t get my handset to switch to the repeater. Re-registering the repeater. - Making sure the repeater and handset are - registered to the same base. The LINK light on the repeater randomly starts blinking. Moving the repeater closer to the base.
34 If static is on 1 handset or in 1 location: If static is on all handsets or in all locations: Check nearby for one of - the common interference sources. Try moving the handset away - from a suspected source, or try moving the suspected source so it’s not between the handset and the base.
35 Liquid damage Moisture and liquid can damage your cordless phone. If the exterior housing of the handset or base is exposed to moisture or liquid, wipe off the liquid, and use as normal.
36 Reseng and Registering Handsets If you are having trouble with a cordless handset or if you want to replace one, you need to clear the registration information from the base and the handset: Do you have the base the handset is registered to? Yes No Press and hold 1.
37 In about 30 seconds, the handset display should say Registration Complete . Press TALK/FLASH and make sure you get a dial tone. If... Try... - you don’t hear a dial tone - the display says Registration Failed Making sure the handset is fully charged, then starting over at step 1.
38 - Only register one repeater at a time. If more than one repeater is in registration mode at the same time then they can interfere with each other. - Only register a repeater to one base at a time. If more than one base is in registration mode at the same time then you can't control which base the repeater registers to.
39 AC Adapter and Baery Informaon Use only the supplied AC adapters. Be sure to use the proper x adapter for the base and any chargers. Do not place the power cord where it creates a trip hazard or x where it could become chafed and create a fire or electrical hazard.
40 INDEX A Answering a Call ...................17 Answering System ................25 B Base Unavailable ..................36 Baery Install ........................1 Baery Informaon ..............39 Bluetooth........................ 2, 3, 4 C Caller ID .
41 S Screening calls ................ 26, 29 Security Code ................. 25, 29 Speaker Volume ....... 10, 11, 18 T T-coil ........................ 14, 15, 34 Talk and Standby Times .......39 Transferring a Call ............... 23 Troubleshoong .
42 WARRANTY One-year limited warranty This product comes with a one year limited warranty. Please refer to our Uniden website for any details or warranty durations offered in addition to those contained below. UNIDEN XDECT R035BT IMPORTANT Evidence of the original purchase is required for warranty service.
43 Product and return it to you without charge for parts and service. This warranty does not provide for reimbursement or payment of incidental or consequential damages.
©2010 Uniden Australia Pty Ltd/Uniden New Zealand Limited Printed in Vietnam UNZZ01156BZ(0).
Ein wichtiger Punkt beim Kauf des Geräts Uniden XDECT R035 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Uniden XDECT R035 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Uniden XDECT R035 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Uniden XDECT R035 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Uniden XDECT R035 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Uniden XDECT R035 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Uniden XDECT R035 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Uniden XDECT R035. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Uniden XDECT R035 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
