Benutzeranleitung / Produktwartung ALP9094 des Produzenten Uniden
Zur Seite of 32
Uniden ALP9094 4-Line Alpha/Numeric Pager owners manual UPZZ01671ZZ.
FCC Information Your pager can interfere with the operation of other electrical devices even when it is functioning properly. To determine if your pager is causing interference, turn the pager off while observing the affected device. If the interference goes away, it was probably caused by your pager.
Important Your pager is capable of storing messages and telephone numbers totaling up to 100,000 characters. To prevent the loss of important data due to battery failure, replace the battery before the power level becomes too low.
Introduction Congratulations on your purchase of the ALP9094 four line alpha/numeric pager. This compact, state-of-the-art pager has many features, including: ● 20 Folder Locations for Mail Drops .
In s t a llin g t h e B atter y Your pager requires one 1.5 VDC, AAA battery for power. Caut ion : Only use the battery specified above. 1. Release the battery compartment lock.Slide and lift off the battery cover. 2. Insert the AAA battery into the compartment according to the polarity symbols (+) and (–) marked inside.
Turning Your Pager On Press and hold N for approximately two seconds. The display will temporarily go blank and then show the standby display (see page 6). Turning Your Pager Off 1. At the standby display, press N to go the Function menu (page 9). 2. Press > to select POWER OFF () .
Co n t r o ls 1. B ackw ar d M enu /P age S cr oll K ey ( < ) 2. Fo rwa rd Men u/ Page Sc rol l Key ( > ) 3. Ente r K e y ( N ) 4. Spe ake r 5. Sc rol l Do wn Ke y ( ▼ ) 6.
Standby Di spl ay 1. Time 2. Message Status - Displays CALL , MAIL , Low Battery , and FULL . This symbol (-----) indicates no messages or calls. This symbol ( ) indicates all messages have been read. 3. Alarm ( ) - Indicates an alarm has been set. 4.
Cle a r v u e Illu m in ated Di spl ay Your pager is equipped with the Clearvue illuminated display. To activate this display, perform the following steps: 1. With your pager on, push and hold any key ( < , > , ▲ , ▼ ,o r N ) for two seconds.
Recei vi ng and Displ ayi ng Per sonal Messag es Your pager can store up to 40 messages in the order that they’re received. If the memory is full when a new message arrives, FULL appears in the bottom center of the display. The newest message then replaces the oldest in memory.
T he F uncti on Menu There are ten choices in the Function menu: Re t u r n - Returns to the previous menu. Se le c t A le rt - Changes the alert type. Po w e r O ff - Turns the unit off. Se t Al arm - Sets the alarm for time, day, and/or date. Fol de rs - Stores up to 25 messages in each of 10 folders.
Choosi ng the Alert Type 1. At the standby display, press N . 2. Press > to choose SELECT ALERT , then press N . 3. Cycle through the alert types with the >< keys (sample alert tones will sound). 4. Select the alert type you like, then press N .
Setting a Dail y Al ar m To set the alarm for a specific time. For example, every day at 1:00 p.m. 1. At the standby display, press N . 2. At the Function menu, press > to select SET ALARM , then press N . 3. Select TIME ALARM with the ▼ key, then press N .
Setting a W eekl y Al arm To set an alarm for a specific day of the week. For example, every Wednesday at 1:00 p.m. 1. At the standby display, press N . 2. At the Function menu, press > to select SET ALARM , then press N . 3. Select TIME ALARM with the ▼ key, then press N .
Setting a Date Alarm To set an alarm for a specific date and time. For example, Friday, November 22, at 1:40 p.m. 1. At the standby display, press N . 2. At the Function menu press > to select SET ALARM , then press N . 3. Select DATE ALARM , with the ▼ key, then press N .
Viewing a Fol der’ s Contents 1. At the Function menu, press > to select FOLDERS , then press N . 2. Press ▼ to move the cursor to the desired folder. 3. Press N to view the folder’s contents. 4. The message displays. Press ▼ to scroll through the message line by line.
Deleti ng a Message F r om a F older 1. View the message by following the steps in “Viewing a Folder’s Contents” (see page 14), then press N . 2. Press > to select DELETE MESSAGE , then press N . 3. Press N , and MESSAGE:## DELETED displays. Deleti ng All Messages F rom a Fol der 1.
Mai l Drop History Mail Drops are messages from services that are updated periodically (news, weather). When you receive a Mail Drop message, MAIL appears in the standby display. Each mail drop history folder holds up to three messages. 1. At the standby display, press N .
Moving , Del eti ng, and Deleti ng Al l Mai l Dr op Messages Please see “Moving,” “Deleting,” and “Deleting All Messages” on pages 14 and 15. These instructions about folders are also applicable to Mail Drop Messages. Perform the same steps, only this time select the Mail Drop History icon instead of the folders icon (where applicable).
U si ng The Phone Di rector y Entering N ames and N umbers Your phone directory can store up to 128 names and numbers. Names can be up to 15 characters long, and numbers can be up to 17 characters long. All entries are sorted alphabetically. 1. Press N at the standby display.
8. Select the entry type with the ▼▲ keys. 9. Press > , then select the numbers with the ▼▲ keys. 10. Press N to move the cursor to the next space. 11. Once finished, press > until the cursor moves to line three. 12. Repeat steps eight and nine to enter the type and number.
Deleti ng N umbers From the Director y 1. At the Function menu, press > to select PHONE DIRECTORY , then press N . 2. Use the ▲▼ keys to display the entry you wish to delete, then press N . 3. Press > to select DELETE ENTRY , then press N . 4.
T he Setup Opti ons Menu There are eight choices in the Setup Options menu: Re t u r n - Returns to previous/standby menu. Se t T im e an d Da te - Sets time and date. Folder Labe ls - Changes a folder’s character labels. M ai l Dr op Opt ions - Sets mail drop options.
Setting the T i me, Day and Date 1. At the Function menu, press > to select SETUP OPTIONS , then press N . 2. Press > to select SET TIME AND DATE , then press N . 3. Use the >< keys to select the minutes, 12/24 hr, or day/date mode. Change the values with the ▼▲ keys.
Mail Drop Options You can set your pager to scroll selected mail drop messages in a “ticker” fashion across the standby display as they are received. 1. At the Function menu, press > to select SETUP OPTIONS , then press N . 2. Press > to select MAIL DROP OPTIONS , then press N .
Reminder F uncti on Your pager will remind you when you have new messages that haven’t been checked. To turn this function Off or On, perform the following steps. 1. At the Function menu, press > to select SETUP OPTIONS , then press N . 2. Press > to select REMINDER , then press N .
Chang i ng the Di splay F ont Si z e 1. At the Function menu, press > to select SETUP OPTIONS , then press N . 2. Press > to select FONT SIZE , then press N . 3. Select the desired font size with the ▼▲ keys. 4. Press N to enter your selection.
Understanding the Memory Status Reminder ● Unread Personal Messages ( ). ● Unread Mail Drop Messages ( ). ● The CALL display. ● The MAIL display. ● All messages have been read ( ). ● Your pager’s memory is FULL . You need to read and/or delete your messages.
Unreadable Messag es If a message is received that is partially or totally unreadable, the unreadable characters are replaced with square dots ( ). Tone Onl y A TONE ONLY message has no numeric characters.It could be an unreadable message, an error, or a preset message that alerts you to check your voice mail.
Sile nt Tim e You can set a range of time when your pager will not sound any alarms. For example, if you are in a meeting from 8:00 to 10:00 a.m. and do not wish to be disturbed by your pager. 1. At the Function menu, press > to select SET SILENT TIME , then press N .
B elt Clip / Ho l ster ● Line the pager up with the holster as shown below. ● Slide the pager into the holster, then press until it snaps into place. ● Use the spring clip (on back of the holster) to attach the holster to your belt or pocket. ● Messages can be viewed while the pager is in the holster.
Two Year Limited Warranty Important: Evidence of original purchase is required for warranty service. WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”) ELEMENTS OF WARRANTY: Uniden warrants, for two.
Ein wichtiger Punkt beim Kauf des Geräts Uniden ALP9094 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Uniden ALP9094 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Uniden ALP9094 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Uniden ALP9094 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Uniden ALP9094 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Uniden ALP9094 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Uniden ALP9094 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Uniden ALP9094. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Uniden ALP9094 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
