Benutzeranleitung / Produktwartung TB4000 des Produzenten Troy-Bilt
Zur Seite of 28
©2000 MTD SOUTHWEST INC Models TB4000 – 26cc Straight Shaft FORM 182825 (12/00) (10197 rev . A) Printed in U.S.A. Owner/Operator Manual 4-Cycle T rimmer/ Brush Cutter • Safety • Assembly • Op.
2 Introduction THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. Y ou will find it to be a great labor -saving device. This operator’ s manual provides you with easy-to-understand oper- ating instructions.
3 Ser vice Information SERVICE INFORMA TION Service on this unit both within and after the warranty period should be performed only by an authorized and approved service dealer .
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger . The instructions or warnings they give are not substitutes for proper accident prevention measur es.
5 Safety (continued) • Add fuel in a clean, well-ventilated area outdoors where ther e are no sparks or flames. Slowly r emove the fuel cap only after stopping engine. Do not smoke while fueling or mixing fuel. Wipe up any spilled fuel from the unit immediately .
6 Safety (continued) • Do not run the unit at high speed when not cutting. • If you strike or become entangled with a foreign object, stop the engine immediately and check for damage. Have any damage repair ed before attempt- ing further operations.
SYMBOL MEANING • UNLEADED FUEL Always use clean, fresh unleaded fuel. • OIL Refer to operator's manual for the proper type of oil. • THROWN OBJECTS AND ROT A TING CUTTER CAN CAUSE SEVERE INJUR Y WARNING: Do not operate without the cutting attachment shield in place.
8 Section 2 Know Y our Unit APPLICA TIONS As a trimmer; • Cutting grass and light weeds. • Edging • Decorative trimming around tr ees, fences, etc.
9 Section 3 Assembly Decal On some units, the J-handle may be preinstalled and only requir e loosening the screws and adjusting the J-handle to the operator . Go to step 6 for adjusting the J-handle if preinstalled. INST ALLING AND ADJUSTING THE J-HANDLE Installing 1.
10 Assembly (continued) INST ALLING THE HARNESS Always use the shoulder harness when using the cutting blade to avoid serious personal injury . 1. Push the strap through the center of the buckle. 2. Pull the strap over the cross bar and down thr ough the slot in the buckle (Fig.
11 Assembly (continued) Fig. 3-8 Remove the Cutting Attachment The gear housing gets hot with use and can result in injury to the operator . When the unit is turned off it remains hot for a short time. Do not touch the gear housing until it has cooled.
12 Assembly (continued) 6. Align the shaft bushing hole with the locking rod slot and insert the locking rod into the bushing hole (Fig. 3-8, Pg. 10). 7. Put the blade retainer and nut on the output shaft. Make sure that the blade is installed corr ectly .
13 Section 4 Oil and Fuel RECOMMENDED OIL TYPE Using the proper type and weight of oil in the crankcase is extremely important. Check the oil befor e each use and change the oil regularly . Failure to use the correct oil, or using dirty oil, can cause pr emature engine wear and failure.
ST ARTING INSTRUCTIONS Operate this unit only in a well ventilated area outdoors. Carbon monoxide exhaust fumes can be lethal in a confined area. Avoid accidental starting. Be in the starting position whenever pulling the starting rope. T o avoid serious personal injury , the operator and unit must be in a stable position while starting.
15 Operation (continued) Starter Rope Throttle Control On/Off Stop Control Primer Bulb P ARTIAL (B) RUN (C) FULL Choke (A) Choke Lever Start/On (I) Stop/Off (O) Fig. 5-1 Fig. 5-2 Fig. 5-3 5. Fully press and r elease the primer bulb slowly 5 to 7 times.
16 Operation (continued) HOLDING THE TRIMMER Always wear eye, hearing, foot and body protec- tion to reduce the risk of injury when operating this unit. Before operating the unit, stand in the operating posi- tion (Fig. 5-4). Check for the following: • The operator is wearing eye protection and pr oper clothing.
Blade thrust may occur when the spinning blade contacts an object that it does not immediately cut. Blade thrust can be violent enough to cause the unit and/or operator to be propelled in any direction, and possibly lose contr ol of the unit. Blade thrust can occur without warning if the blade snags, stalls or binds.
18 Section 6 Maintenance NOTE: Some maintenance procedures may require special tools or skills. If you are unsure about these procedures take your unit to an authorized service dealer . MAINTENANCE SCHEDULE These requir ed maintenance procedur es should be performed at the frequency stated in the table.
19 Maintenance (continued) 5. Check the indexing teeth on the inner reel and outer spool for wear (Fig. 6-2). If necessary , remove burrs or replace the r eel and spool. NOTE: Membrane line can only be used with the inner reel with the slotted holes. Single line can be used on either type of inner reel.
20 Maintenance (continued) INST ALLING A PREWOUND REEL 1. Hold the outer spool with one hand and unscrew the Bump Knob clockwise (Fig. 6-1, Pg. 18). Inspect the bolt inside the Bump Knob to make sure it moves fr eely . Replace the Bump Knob if damaged.
21 Maintenance (continued) Fig. 6-11 1. Unplug spark plug boot to eliminate starting 2. Remove the oil fill plug/dipstick. 3. Pour the oil out of the oil fill hole and into a con- tainer by tipping the unit to a vertical position (Fig. 6-11). Allow ample time for complete drainage.
22 Maintenance (continued) CARBURETOR ADJUSTMENT The idle speed of the engine is adjustable the screw next to the air filter cover (Fig 6-15). NOTE: Careless adjustments can seriously damage your unit. An authorized service dealer should make carburetor adjustments.
23 Maintenance (continued) 9. If the clearance is not within specification: a. T ur n the adjusting nut using a 5/16 inch (8 mm) wrench or nut driver (Fig. 6-19). T o increase clearance, turn the adjusting nut counterclockwise. T o decrease clearance, turn the adjusting nut clockwise.
24 Maintenance (continued) ACCESSORIES/REPLACEMENT P ARTS Oil Fill Plug / Dipstick . . . . . . . . . . . . . . . . . . . . . . . . . .181975 Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180852 Spark Arrestor . . . . .
25 Section 7 T roubleshooting CAUSE ACTION Cutting attachment bound with grass Stop the engine and clean cutting attachment Cutting attachment out of line Refill with new line Inner reel bound up Repl.
26 Section 8 Specifications Engine T ype . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air -Cooled, 4-Cycle Displacement . . . . . . . . . . . . . . . . . . . .
27 Section 9 W arranty CALIFORNIA EMISSION CONTROL WARRANTY ST A TEMENT YOUR WARRANTY RIGHTS AND OBLIGA TIONS The California Air Resources Board and MTD Southwest Inc (MTD), are pleased to explain the emis- sion control system warranty on your 2000 and later small off-r oad engine.
MANUF ACTURER’S LIMITED W ARRANTY FOR: No implied warranty , including any implied warranty of merchantability or fitness for a particular purpose, applies after the applicable period of express written warranty above as to the parts as identified.
Ein wichtiger Punkt beim Kauf des Geräts Troy-Bilt TB4000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Troy-Bilt TB4000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Troy-Bilt TB4000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Troy-Bilt TB4000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Troy-Bilt TB4000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Troy-Bilt TB4000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Troy-Bilt TB4000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Troy-Bilt TB4000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Troy-Bilt TB4000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
