Benutzeranleitung / Produktwartung UL2000B des Produzenten Behringer
Zur Seite of 26
User’s manual Version 1.0 August 2006 ULTRALINK UL2000B.
2 UL TRALINK UL2000B CAUTION: To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside; refer servicing to qualified personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture.
3 UL TRALINK UL2000B TABLE OF CONTENTS 1 . INTRODUCTION ......................................................................................................... 4 1.1 Before you get started ............................................................
4 UL TRALINK UL2000B 1. INTRODUCTION Thank you very much for expressing your confidence in the ULTRALINK Series by purchasing this unit. With the UL2000B from BEHRINGER, you have acquired a modern, high-performance wireless transmission system.
5 UL TRALINK UL2000B 1.1.3 Initial operation of the receiver Assure adequate ventilation and never place your ULR2000 receiver on top of an amplifier or near radiators to avoid overheating. The wall power unit (model: E-SPS1) included in the delivery supplies the power to your ULR2000.
6 UL TRALINK UL2000B 1.1.5 Online-Registration Please do remember to register your new BEHRINGER equipment right after your purchase by visiting www.behringer.com (alternatively www.behringer.de) and kindly read the terms and conditions of our warranty carefully.
7 UL TRALINK UL2000B DISPLAY All important parameters are shown in the display (ch. 2.1.2). SET The SET button has 2 functions: Press this button to bring up the menu.
8 UL TRALINK UL2000B Alphanumeric display All the values and letters relevant to the operation of your ULR2000 are shown in the 6-digit alphanumeric display: for example, channel number, channel color, frequency and menu items.
9 UL TRALINK UL2000B If menu is selected and you make no parameter changes for a while, the unit automatically exits the menu. 2.2.1 TUNE A freely selectable carrier frequency in the range between 798.100 - 805.900 MHz can be set in the TUNE menu.
10 UL TRALINK UL2000B 0 d B: the receiver is not muted low dB value: the receiver is muted only if substantial noise is transmitted with the signal high dB value: the receiver is muted even if the noise floor is low Setting a Squelch value 1 .
11 UL TRALINK UL2000B 4 . Press the UP and DOWN buttons to set one of the 3 parameters (FREQU, CHANNL or COLOR). 5 . Press the SET button to store the parameter for the basic setting. The procedure is now over, and the new basic setting is shown in the display.
12 UL TRALINK UL2000B 3 . Press the SET button again to get to the PRESET submenu. The display shows the currently active preset. 4 . Press the UP and DOWN buttons to select the desired preset. The display shows PSET 1 (2, 3 or 4). 5 . Press the SET button to load up the preset you selected .
13 UL TRALINK UL2000B 2 . A blink code indicates the charge level of the battery: 1 = Battery is nearly empty . . . 5 = Battery is fully charged 3 . Shortly after, a second blink code indicates the current channel setting for the transmitter: 1 = Channel 1 is selected .
14 UL TRALINK UL2000B The value 0 is indicated by a very short blink of the LED, and you will easily tell a 0 from a 1. If no entry is made for more than 5 seconds (either on the selection switch or by pressing the POWER button), the LED blinks quickly 5 times, and the programming mode is aborted.
15 UL TRALINK UL2000B If you have not stored any of your own frequencies, the frequencies stored in the user preset (Preset 1) are identical to the frequencies stored in Preset 3. Loading a preset 1 . Engage MUTE. The transmitter can now be switched into the programming mode.
16 UL TRALINK UL2000B Low Gain: the LED blinks once with medium tempo. High Gain: the LED blinks twice with medium tempo. If no entry is made for more than 5 seconds (either on the selection switch or by pressing the POWER button), the LED blinks quickly 5 times, and the programming mode is aborted.
17 UL TRALINK UL2000B 6 . After a second brief blink break, an additional blink code is given as a confirmation: Two slow blinks signal that the Auto Mute setting was changed. The transmitter leaves the programming mode. If the setting for Auto Mute could not be stored, the LED blinks quickly 5 times.
18 UL TRALINK UL2000B Low Gain: The LED blinks once with medium tempo. High Gain: The LED blinks twice with medium tempo. 3.3.5 Auto Mute 1 . Make sure the transmitter is not muted (MUTE switch is set to OFF). 2 . Turn the selection switch to 7 or 8 and confirm your selection by briefly pressing the POWER button.
19 UL TRALINK UL2000B 5. INST ALLA TION 5.1 Operating information The quality of the wireless transmission depends on various local factors as well as the degree of radiation and reception at transmitter and receiver, unlike the signal transmission over cable.
20 UL TRALINK UL2000B T o assure good reception, if possible, inst all the ULR2000 as high in a rack as possible, so that the antennae protrude above the upper edge of the rack. The ULR2000 requires one height unit (1 HE) for installation in a 19-inch rack.
21 UL TRALINK UL2000B 5.3 Audio connections The audio connections on the ULR2000 are laid out electronically balanced. Of course, you can connect unbalanced equipment to the balanced connectors. Fig. 5.2: XLR connections Fig. 5.3: 1/4 " TS connector Fig.
22 UL TRALINK UL2000B A cable connection is required to connect the headset to the transmitter. The plug connection is provided by means of mini XLR connectors, which ensure a secure operation due to their locking mechanism. Abb.5.5: Mini XLR connector of the ULB2000 5.
23 UL TRALINK UL2000B 6. SPECIFICA TIONS 6.1 ULR2000 receiver RF characteristics Receiver principle True Diversity Modulation wideband FM Frequency range 794 - 810 MHz Receiving frequencie s (for EU/US/CA) 3 20 frequencies, between 798.
24 UL TRALINK UL2000B 6.2 ULB2000 transmitter RF characteristics Modulation wideband FM Frequency range 794 - 810 MHz Transmission frequencies (for EU/US/CA) 320 frequencies, between 798.1 - 805.9 MHz, adjustable in 25-kH z increments Channels 8, freely programmable and switchable Ch a nn el b an d wi dt h < 200 kHz Channel spacing (min.
25 UL TRALINK UL2000B FEDERAL COMMUNICA TIONS COMMISSION COMPLIANCE INFORMA TION Responsible party name: BEHRINGER USA, Inc. Address: 18912 North Creek Parkway, Suite 200 Bothell, WA 98011, USA Phone/Fax No.
26 UL TRALINK UL2000B MICROPHONE QUICK ST ART GUIDE MICROPHONE QUICK ST ART GUIDE.
Ein wichtiger Punkt beim Kauf des Geräts Behringer UL2000B (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Behringer UL2000B noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Behringer UL2000B - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Behringer UL2000B reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Behringer UL2000B erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Behringer UL2000B besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Behringer UL2000B verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Behringer UL2000B. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Behringer UL2000B gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
