Benutzeranleitung / Produktwartung PA3686U-1SET dynadock wireless des Produzenten Toshiba
Zur Seite of 76
GMAA00165010 07/09 dynadock ™ wireless U User’ s Manual.
2 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipment, or loss of data.
3 5.375 x 8.375 ver 2.3 Safety instructions Always read the safety instructions carefully: Do not disassemble, modify , tamper with or repair the product ❖ Do not attempt to disassem ble, modify , tamper with or repair the product (including the AC adaptor).
4 5.375 x 8.375 ver 2.3 Only use TOSHIBA AC adaptor ❖ Always use the TOSHIBA AC adaptor t hat may have been provided with your product, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the pr oduct.
5 5.375 x 8.375 ver 2.3 Never place your product in locations with excess heat ❖ Never place your product where it will be exposed to excess heat, such as in direct sunlight , in an unventilated vehicle or ne ar a heater . This may result in a system failure, malfunction, loss of data or damage to the product.
6 5.375 x 8.375 ver 2.3 FCC Conditions This equipment has been tested and found to comply with Part 15 of the FCC Rules. Operation is subject to the following tw o conditions: (1) This device may not cause harmful interference (2) This device must accept any interference receiv ed, including interference that may cause undesired operation.
7 5.375 x 8.375 ver 2.3 Copyright statement This guide is copyrighted by T oshiba Corp oration with all rights reserved. Under the copyright laws, this guide cannot be re produced in any form without the prior written permission of T oshiba. No patent liability is assumed, ho wever , with respect to the use of the information contained herein.
8 5.375 x 8.375 ver 2.3 T rademarks dynadock is a trademark of T oshiba Corporation. Adobe and Reader ar e either registered trademar ks or trademarks of Ad obe Systems Incorporated in the Unite d States and/or other countries. AMD, AMD K6, Athlon and Dur on are regi stered trademarks or trademarks of Advanced Micro De vices Incorporated.
9 5.375 x 8.375 v er 2.3 Contents Safety icons .............................................................. 2 Safety instructions ....................................................3 FCC information .................................................
10 Contents 5.375 x 8.375 v er 2.3 Connecting your peripherals ...................................28 Connecting to a network ...................................28 Connecting a monitor .......................................29 Connecting audio devices .
11 Contents 5.375 x 8.375 v er 2.3 Chapter 3: T roubleshooting and Support ........ ........................ 59 Troubleshooting ......................................................59 Power ............................................................
12 I n t roduct ion Thank you for purchasing t he dynadock™ wireless U, the universal docking station that enables you to connect your compu ter peripherals wirelessly or through a single USB cable to just about any W indo ws ® -based computer . The wireless function uses UWB (ultra-wide band) radio technology .
13 Introduction Overview 5.375 x 8.375 ver 2.3 Overview Features ❖ W ireless or single USB cable connection to your computer* ❖ Upright slim design saves desktop space ❖ Easily accessible USB an.
14 Introd uctio n Quic k T our 5.375 x 8.375 ver 2.3 Quick T our This section identifies the v arious components of the dynadock ™ wireless U. For a description of each component, please refer to th e table beneath each illustration.
15 Introduction Quick T our 5.375 x 8.375 ver 2.3 Component Description Power light Glows blue when power is being supplied fro m the AC adapto r . Indicator light Indicates the status of docking, undocking, and charging fu nctions as foll ows: Flashing green: Docking is in process.
16 Introd uctio n Quic k T our 5.375 x 8.375 ver 2.3 Back view (Sample Illustration) Connections on the back of the dynadock™ USB 2.0 ports Mini USB jack DC-IN Security Lock Slot S/PDIF port Line ou.
17 Introduction Quick T our 5.375 x 8.375 ver 2.3 Component Description Antennas Send and receive wireless signal s to/from the connected computer . Antenna switch Slide the switch down [] to enable wireless communication between yo ur computer and th e dynadock™.
18 Introd uctio n P ackage con te nt s 5.375 x 8.375 ver 2.3 T op view (Sample Illustration) The top of the dynadock™ Package contents Check to make sure you have all of the follo wing items: ❖ dynadock™ wireless U docking station ❖ Base ❖ USB 2.
19 Introduction Computer r equir ements 5.375 x 8.375 ver 2.3 Computer requirements ❖ 1.2 GHz or higher processor (Intel ® Pentium ® /Celeron ® family , or AMD K6 ® /AMD Athl on™/AMD Duron™ family , or compatible processor recommended. Intel ® Core™ 2 Duo 2.
20 Chapter 1 Setting Up the dynadock™ and Connecting Peripherals Setting up the dynadock™ This section provides instruct ions on setting up the dynadock™ .
21 Setting Up the dynadock™ and Connect ing Peripherals Setting up the dynadock™ Connect the power adaptor 1 Plug the A C adaptor cord/cable into the DC-IN on the back of the dynadock™.
22 Setting Up the dynadock™ and Connectin g Peripherals Setting up the dynadock™ Y ou may need to temporarily disable anti-spyware or anti-virus programs while installing the softwar e. It is also recommended that all other applications are closed, as you will need to restart your computer after the software is installed.
23 Setting Up the dynadock™ and Connect ing Peripherals Setting up the dynadock™ (Sample Image) dynadock Installer The follo wing programs are installed durin g the installation process: 4 Follo w the on-screen instructio ns to finish the installatio n.
24 Setting Up the dynadock™ and Connectin g Peripherals Setting up the dynadock™ Connect the dynadock™ to your computer Y ou may either: ❖ Set up a wireless connec tion OR ❖ Set up a USB cable connection Refer to the appropriate section belo w for the type of connection you wish to establish.
25 Setting Up the dynadock™ and Connect ing Peripherals Setting up the dynadock™ (Sample Illustration) W i r eless communica tion enabled 3 Make sure your computer is turned on. 4 Connect a Certified W i reless USB adaptor (included with certain models) to your computer and place the adaptor's antenna in an upright position.
26 Setting Up the dynadock™ and Connectin g Peripherals Setting up the dynadock™ (Sample Illustration) Connecting the USB cable to the Mini USB port 6 Plug the other end of the USB cab le into an av ailable US B 2.
27 Setting Up the dynadock™ and Connect ing Peripherals Setting up the dynadock™ 8 After successfully completing the association, remove the USB cable connecting the computer to the dy nadock™. After a few moments, a wireless connection is established and a message displays on your computer screen asking if you want to dock your computer .
28 Setting Up the dynadock™ and Connectin g Peripherals Connecting your peripherals Set up a USB cable connection 1 Mov e the switch on the back of the dynadock™ to the USB [] position. 2 Connect the provided USB cable to the Mini USB port on the back of the dynadock™.
29 Setting Up the dynadock™ and Connect ing Peripherals Connecting your peripherals 2 In the Network Connect ions folder, double-click the Connection icon for the dynadock’ s Ethernet adaptor, which is indicated by ASIX AX88772A USB2.0 to Fast Ethernet Adaptor .
30 Setting Up the dynadock™ and Connectin g Peripherals Connecting your peripherals Y ou can customize the video settings of the dynadock™. See “ A djusting video settings” page 47 for more informat ion. Connecting audio d evices The dynadock™ provides four audio ports, as sho wn in the following illustrations.
31 Setting Up the dynadock™ and Connect ing Peripherals Connecting your peripherals When your computer is docked, the audio ports on the computer are automatically disabled and the audio port s on the dynadock™ are automatically enabled.
32 Setting Up the dynadock™ and Connectin g Peripherals Connecting your peripherals If you want to charge your USB device when the computer connected to the dynadock™ is off or when there is no computer connected to the dynadock™, be sure to connect your de vice to one of the powered USB ports on the front of the dynadock™.
33 Chapter 2 Using the dynadock™ and Adjusting Settings Undocking your computer T o avoid losing data and/or damaging your computer and/or peripherals, be sure to undock your computer from the dynadock™ as described in this section before you do any one of the following: ❖ Disconnect the USB wireless adaptor from your computer .
34 Using the dynadock™ and Adjusting Setting s Undocking your computer Undocking via the undock button 1 Press the Undock button on the top of the dynadock™ once. The indicator light on the front of the dynadock™ flashes orange, and the following message appears on your computer screen.
35 Using the dynadock™ and Adjusting Setting s Undock ing your computer The indicator light on the front of the dynadock™ flashes orange, and the following message appears on your computer screen.
36 Using the dynadock™ and Adjusting Setting s Re-connecting and docking your computer (Sample Image) The Eject and Sleep command 3 W ait before disconnecting the dynado ck™ from the computer .
37 Using the dynadock™ and Adjusting Setting s Using the dynadock™ softwar e Using the dynadock™ software This section provides in formation on using the following software to manage the dynadoc.
38 Using the dynadock™ and Adjusting Setting s Using the dynadock™ softwar e If you are using a non-T oshiba Certified Wireless USB adaptor or a Certified Wireless USB radio bu ilt into your compu.
39 Using the dynadock™ and Adjusting Setting s Using the dynadock™ softwar e Changing the Conn ection Rules The Connection Rules t ab of the Wire less USB Manager allows you to change the default association behavior of the host radio.
40 Using the dynadock™ and Adjusting Setting s Using the dynadock™ softwar e If you permanently remove the device, you will not be able to connect to that particular device again until the device has been re-associated. T o re-associate the device, follow the instructions in the section “Set up a wireless connection” on pa ge 24 .
41 Using the dynadock™ and Adjusting Setting s Using the dynadock™ softwar e If you wish to m anually select the channel to be used f or communications betw een the dynad ock™ and your co mputer , you can do so by clicking the Requested Channel drop-do wn menu and then selecting any channel from the list.
42 Using the dynadock™ and Adjusting Setting s Using the dynadock™ softwar e Using the TOSHIBA dynadock Utility The TOSHIB A dynadock U tility provides optio ns for changing default settings, undocking, configuring audio ports, and more.
43 Using the dynadock™ and Adjusting Setting s Using the dynadock™ softwar e If the TOSHIBA dynadock Utility icon is not visible in your System tray/Notification Area, make sure the dynadoc k™ is connected and docked, and then click the Show Hidden Icons button [ ], if necessary , to display hidden icons.
44 Using the dynadock™ and Adjusting Setting s Using the dynadock™ softwar e Enabling/disabling Charge mode When the dynadock™ is disconnected from your computer or the computer's po wer is turned off, the front USB ports will charge certain connected USB de vices if Char ge mode is enabled.
45 Using the dynadock™ and Adjusting Setting s Using the dynadock™ softwar e 2 Click Settings . 3 Select the checkboxes ne xt to Show undocking complete message and Show unexpected r emove message to turn these messages on, or de-select the checkboxes to turn them off.
46 Using the dynadock™ and Adjusting Setting s Using the dynadock™ softwar e If the icon is not visible in your System tray/Notification Area, make sure the dynadock™ is connected and docked, and then clic k the Show Hidden Icons button [ ], if necessary , to display hidden icons.
47 Using the dynadock™ and Adjusting Setting s Adjusting video settings settings for each location. The settings will be retained each time you use the dynadock™ with your computer . Uninstalling the software T o remove the dynadock™ software from your com puter , please follow the steps below .
48 Using the dynadock™ and Adjusting Setting s Adjusting video settings Mirror mode duplicates the image on your comp uter screen on the external monitor(s) connected to the dynadock™. This mode is useful if, for example, you want to vie w information on a larger , external desktop monitor instead of a smaller, b uilt-in com puter screen.
49 Using the dynadock™ and Adjusting Setting s Adjusting video settings Supported display mod es Three components make up the display mode: resolution, co lor depth, and refresh rate.
50 Using the dynadock™ and Adjusting Setting s Adjusting audio settings Please note the follo wing: ❖ Interlaced modes ar e not supported. ❖ The display modes listed above may not be supported by your monitor , or your m onitor may offer additional modes not supported by the dynadock™.
51 Using the dynadock™ and Adjusting Setting s Adjusting audio settings If the icon is not visible in your System tray/Notification Area, make sure the dynadock™ is connected and docked, and then clic k the Show Hidden Icons button [ ], if necessary , to display hidden icons.
52 Using the dynadock™ and Adjusting Setting s Adjusting audio settings ❖ T o use the docked comput er's Microphone jack, select a different rec ording device (oth er than USB Multi-Channel Audio Device). 4 Click Set Default . 5 Click OK . 6 Connect your microphone to the jack you enabled in step 3.
53 Using the dynadock™ and Adjusting Setting s Adjusting audio settings (Sample Image) The USB Mult i-Channel Audio Device Utility 3 In the Analog Output section of the dialog box, select one of the following: ❖ Headphone or [ ], if you connected headphones in step 1.
54 Using the dynadock™ and Adjusting Setting s Adjusting audio settings The Speaker Shifter controls display . 6 Use the Shifter co ntrols to adjust your virtual sp eaker settings, as indicated in the table belo w .
55 Using the dynadock™ and Adjusting Setting s Adjusting audio settings 7 Click the Advanced Settings b utton next to DSP Mode to close the Shifter controls and return to the basic controls screen. 8 Adjust other settings, if desired, to s ui t y o ur sound preferences.
56 Using the dynadock™ and Adjusting Setting s Char ging USB devices 2 Click the USB Multi-Channel A udio Device icon in the System tray/Notification Area of your W indows ® desktop.
57 Using the dynadock™ and Adjusting Setting s Using standby/sleep/hibernation mod es with the dynadock™ T o charge a device when the dyna dock™ is disconnected or the connected computer is of f: 1 Make sure the dynadock's A C adaptor is connected to an electrical outlet.
58 Using the dynadock™ and Adjusting Setting s Securing the dynadock™ Securing the dynadock™ The security lock slot enables you to connect a security cable (not provided) to help prevent unauthorized remov al of the dynadock™.
59 Chapter 3 T roubleshooting and Support T roubleshooting This section pro vides answers for problems you may encou nter when using your dynadock™. Som e problems are relatively easy to identify and solve; ho wever , others ma y require help from your network administrator or company technical support staff.
60 T roubleshooting and Support T r oubleshooting Due to USB bandwidth limitations, you may notice performance issues if you are performing several resource-intensive tasks simultaneously (such as playing audio over more than two channels while simultaneously recording audio, transferring large files and using a high-definition web camera).
61 T roubleshooting and Supp ort T r oubleshootin g Display/Video For additional information on troubleshooting dynadock™ video issues, please visit the DisplayLink W eb site at www .displaylink.com . Problem(s) Solution(s) External monitor does not turn on (the monitor’ s power light does not turn on).
62 T roubleshooting and Support T r oubleshooting The Fn + F5 and Fn + Space hot keys on my T oshiba computer do not affect the external monitor connected to my system via the dynadock™.
63 T roubleshooting and Supp ort T r oubleshootin g I cannot open the A TI Catalyst Control Center on my computer since I installed the dynadock™ display drivers and utility . Some versions of A TI Catalyst C ontrol Center are not supported by the dynadock™.
64 T roubleshooting and Support T r oubleshooting Mirror mode is not available (grayed out). Mirror mode is not availa ble if the externa l monitor connected to the dynadock™ is set as the primar y display . T o enable Mirror mode, set the computer's built-in display as the primar y display in the Windows Displa y Properties dialog box.
65 T roubleshooting and Supp ort T r oubleshootin g Audio/sound Problem(s) Solution(s) There is no sound coming from the external audio device connected to the dynadock™. Check and adjust the v olume settings. Make sure the cable connecting the audio devi ce to the dynadock’ s Line out, Headph one, or Microphone jack is secure.
66 T roubleshooting and Support T r oubleshooting Connection/Docking Sound is distorted or delayed when playing some multimedia files. Disconnect the dynado ck™ from your computer and play the file again. Problem(s) Solution(s) My computer does not automatically detect the Certified Wireless USB adaptor .
67 T roubleshooting and Supp ort T r oubleshootin g Network The connection to the dynadock™ has been lost. The computer may be out of wire less communication range. Bring the computer within clos e range of the dynadock™ to automatically reconnect.
68 T roubleshooting and Support T r oubleshooting USB Problem(s) Solution(s) USB device does not work. Make sure the dynadock™ is connected to your computer (wirelessly or with a USB ca ble) and the computer is docked (indicator lig ht on dynad ock™ is green) .
69 T roubleshooting and Supp ort T oshiba Support Other T oshiba Support If you require additional help or are still having problems operating the dynadock™, you may need to contact T oshiba for additional technical assistance.
70 T roubleshooting and Support Contacting T oshib a T oshiba voice contact Before calling T osh iba, make sure you have: ❖ Y our dynadock’ s serial number ❖ The computer and any optional device.
71 Appendix A Specifications Specifications This section summarizes the dyn adock’ s technical specifications.* Physical dimensions Environmental requirements Power requirements Weight 490 g/17.2 oz (including the base) Size 42 (w) x 77 (d) x 222 (h) mm/1.
72 Specifications General specifications *Specifications are subject to change without further notice. Computer Interface USB 2.0 or UWB (ultra-wide band radio link) Ports and Connectors 4 USB 2.
73 Index A AC p ow e r connection 21 adjusting audio settings 50 video settings 47 antenna switch 17 antennas 17 assemble dynadock™ 20 associations dynadock™ with computer 39 audio devices connect.
74 Index monitor to dynado ck™ 29 peripherals 28 to a network 28 USB cable to computer 26 USB devices 31 connecting/disconnect ing dynadock™ from com puter 39 Connection Rules changing 39 connecti.
75 Index L light indicator 15 power 15 Line out 17 M Microphone jack 15 Mini USB jack 17 monitor connecting 29 N Network issues 67 network connecting 28 Network port 17 O Optical S/PDIF 17 Other issue.
76 Index uninstalling 47 sound quality enhancing 52 specifications 71 Standby mode 57 switch antenna switch 17 T top vie w Quick T ou r 18 To s h i b a We b s i t e 69 TOSHIB A dynadock Utility using .
Ein wichtiger Punkt beim Kauf des Geräts Toshiba PA3686U-1SET dynadock wireless (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Toshiba PA3686U-1SET dynadock wireless noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Toshiba PA3686U-1SET dynadock wireless - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Toshiba PA3686U-1SET dynadock wireless reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Toshiba PA3686U-1SET dynadock wireless erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Toshiba PA3686U-1SET dynadock wireless besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Toshiba PA3686U-1SET dynadock wireless verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Toshiba PA3686U-1SET dynadock wireless. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Toshiba PA3686U-1SET dynadock wireless gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
