Benutzeranleitung / Produktwartung B-SA4T des Produzenten Toshiba
Zur Seite of 58
PRINTED IN JAPAN TOSHIBA Thermal Printer B-SA4T SERIES Document No. EO15-33001A Original Jul., 2005 (Revised Sep., 2005 ) Option Installation Manual.
EO15-33001A (Revision Date: Feb. 14, 2008) TABLE OF CONTENTS Page 1. Cutter Module ------------------------------------------------------------------------------------------------------ 1- 1 1.1 B-SA204-QM/ B-SA204-QM-R ---------------------------------------------------------------------------- 1- 1 1.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 1- 1 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 1. Cutter Module 1.1 B-SA204-QM / B-SA204-QM-R B-SA204-QM/ B-SA204-QM-R is an optional cutter m odule for the B-SA4TM Series (Metal cover).
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 1- 2 2. Open the Front Cover wider. Remo ve the Front Cove r by lifting it to disengage the hin ge pins from the hinge. The Front Cover cannot be re moved unless it is opened at an angle of ove r 100 degrees as the stoppers of the hinge prevent disengagement.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 1- 3 5. Connect the Cutter Harness to the connec tor at the front of the printer. 6. Close the Cutter Unit and secure it to the printer with the Set Screw. 7. Close the Cutter Module Cover.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 1- 4 1.2 B-SA204P-QM-R B-SA204P-QM-R is an optional cutter module fo r the B-SA4TP Series (Plastic cover). • Packing List The following parts are supplied with the kit. Make sure you have all items shown below.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 1- 5 3. Mount the Cutter Module Cover by in serting the hinge pins into the hinges. 4. Fit the Cutter Unit to the front of the printer by inserting the Hinge Pins into the Hinge Pin Holes.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 1- 6 6. Secure the ground wire of the cutter unit to the prin ter with the B-3x6 screw removed in Step 1, as shown in the picture. 7. Connect the cutter harness to the connec tor at the front of the printer.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module 2- 1 2. Strip Module NOTE: Make sure that the firmware version is V1.1 or gr eater. Firmware V1.0 does not suppo rt the strip m odule. 2.1 B-SA904-H-QM-R B-SA904-H-QM-R is an optional strip module for the B-SA4TM Series (Metal cover).
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 2- 2 2. Open the Front Cover wider. Remo ve the Front Cove r by lifting it to disengage the hin ge pins from the hinge. The Front Cover cannot be re moved unless it is opened at an angle of ove r 100 degrees as the stoppers of the hinge prevent disengagement.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 2- 3 5. Secure the Strip Unit to the printer with the two screws. Make sure that the Feed Roller Gear rotates smoothly. 6. Close the Strip Unit. 7. Connect the Strip Harness to the c onnector at the front of the printer.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module 2- 4 • Attaching the Cutter The enclosed cutter is used to tear off the batch-iss ued labels. Attach the cutter with the two SMW-3x6 screws as shown in the picture below.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module 2- 5 • System Mode Settings for Stripping PET Labels When using PET labels on the strip module, please set the following sy stem mode parameters in advance.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module 2- 6 9. Turn off the printer, and then back to on. Send an issue command to the printer for strip issue. 10. If necessary, fine adjust the print start position and strip position in the system mode.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module 2- 7 13. Press the [PAUSE] key repeatedly until “P.P.FEED” appears on the LCD. 14. Press the [FEED] key to feed a label for checking the next label’s stop position.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan: 19, 2006) 2. Strip Module 2- 8 2.2 B-SA904P-H-QM-R B-SA904P-H-QM-R is an optional strip module fo r the B-SA4TP Series (Plastic cover). • Packing List Strip Unit (1 pc.) Strip Module Cover (1 pc.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 2- 9 2. Open the Front Cover wider. Remove the Fro nt Cove r by lifting it to disengage the hinge pins from the hinge. The Front Cover cannot be re moved unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 2- 10 5. Secure the Strip Unit to the printer with the two screws. Make sure that the Feed Roller Gear rotates smoothly. 6. Close the Strip Unit. 7. Close the Strip M odule Cover.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module 2- 11 • Attaching the Cutter The enclosed cutter is used to tear off the batch-iss ued labels. Attach the cutter with the two SMW-3x6 screws as shown in the picture below.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 3. Wireless LAN Module: B-SA704-WLAN-QM 3- 1 3. Wireless LAN Module: B-SA704-WLAN-QM The pictures used in this section are those of the B-SA4TM, and the installation procedures are common with the B-SA4TP unless otherwise noted.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 3. Wireless LAN Module: B-SA704-WLAN-QM 3- 2 • Installation Procedure 1. Remove the two SMW-3x6 screws from the back of the printer. 2. Remove the Side Panel in the following order. Please note th e procedure is different between the B- SA4TM series and the B-SA4TP series.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 3. Wireless LAN Module: B-SA704-WLAN-QM 3- 3 3. Remove the two SMW-3x6 screw s to detach the Blind Plate. 4. Remove the SMW-3x8 screw to detach the Cable Clamp. 5.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 3. Wireless LAN Module: B-SA704-WLAN-QM 3- 4 6. As the following picture shows, secure the Wireless LAN Board to the printer back with two of the enclosed SMW-3x6 screws.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 3. Wireless LAN Module: B-SA704-WLAN-QM 3- 5 8. Connect the Wireless LAN Power Cabl e and the LAN Cable as shown below. 9. Fit the Antenna Cover to the back of the prin ter. Secure it with the SMW-3x6 screw.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 3. Wireless LAN Module: B-SA704-WLAN-QM 3- 6 • Country Code As available frequency bands are diffe rent from country to country, be sure to set a country code before installing a wireless LAN module in a user’s printer.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 4- 1 4. Serial Interface Board: B-SA704-RS-QM-R The pictures used in this section are those of the B-SA4TM, and the installation procedures are common with the B-SA4TP unless otherwise noted.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 4- 2 2. Remove the Side Panel in the following order. Please note th e procedure is different between the B- SA4TM series and the B-SA4TP series. B-SA4TM B-SA4TP (1).
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 4- 3 4. Attach the enclosed PCB Support Plate to the prin ter back with one of the enclosed SMW-3x6 screws. 5. Fit the Locking Support into the MAIN PC Board.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 4- 4 7. Secure the SIO PC Board to the printer back with the two SMW-3x6 screws. Fit the Locking Support into the SIO PC Board. 8. Re-attach the Side Panel.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 5. 300 dpi Print Head Kit: B-SA704-TPH3-QM-R 5- 1 5. 300 dpi Print Head Kit: B-SA704-TPH3-QM-R B-SA704-TPH3-QM-R is an optional 300 dpi print head kit for the B-SA4TM/SA4TP-GS12 Series (203dpi printer).
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A 7. Expansion IO Board: B-SA704-IO-QM-R 5- 2 • Installation Procedure 1. Fully open the Ribbon Cover. 2. Slightly open the Top Cover (10 mm). 3. Unlock the Print Head by pressing the hooks toward the center.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 6- 1 6. Real Time Clock: B-SA704-RTC-QM-R B-SA704-RTC-QM-R is an optional Real Time Clock fo r the B-SA4TM/SA4TP Series .
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 6- 2 2. Remove the Side Panel in the following order. Please note th e procedure is different between the B- SA4TM series and the B-SA4TP series.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 6- 3 NOTES: 1. Place the battery wi th the “+” mark facing up. 2. A new battery is supposed to last about 2 y ears or more, but it varies depending on the operating conditions.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 6- 4 5. Pass the Interface Cable through the Cable Clamp, and between CN1 and CN2 on the MAIN PC Board, as shown in the pictur es below.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 6- 5 • System Setting (Date and Time Setting) Set the date and time usi ng the following procedure. NOTE: Make sure that the printer version is V1.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 6- 6 10. Pressing the [PAUSE] key enables setting the Hour. 11. Set the Hour with the [FEED] or [RESTART] key. Pressing the [PAUS E] key fixes the Hour and cause the cursor to move to the Minute.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 7. Expansion I/O Board: B-SA704-IO-QM-R 7- 1 7. Expansion I/O Board: B-SA704-IO-QM-R B-SA704-IO-QM-R is an optional expansion I/O board fo r the B-SA4TM/SA4TP Series.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 7. Expansion I/O Board: B-SA704-IO-QM-R 7- 2 2. Remove the Side Panel in the following order. Please note th e procedure is different between the B- SA4TM series and the B-SA4TP series.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 7. Expansion I/O Board: B-SA704-IO-QM-R 7- 3 4. Attach the Expansion I/O Board to the printe r back with one of the supplied SMW-3x6 screws. 5. Connect the Interface Cable to CN4 on the MAIN PC Board.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 14, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 1 8. RFID Module: B-SA704-RFID-U2-EU-R This optional device is intended for adding the RFID tag read/write function to the B-SA4TM and B-SA4TP series.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 2 • Packing List All the following parts are supplied with the ki t. Make sure you have all items shown below. Parts (Quantity) Parts (Quantity) Parts (Quantity ) Antenna Ass’y (1 pc.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 3 • Outline of the introduction of an RFID Kit Please follow the steps below to install the RFID kit, configure various settings, and try data write onto tags.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 4 2. Remove the Side Panel in the following order. Please note the procedure is different between the B- SA4TM series and the B-SA4TP series.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 5 3. Slightly push the Upper S ensor Lever inside (1), and open t he Upper Sensor Ass’y (2).
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 6 6. As the following picture shows, pass the Interface Cable through the opening behind the Stepping Motor so that the cable reac hes the Main PC Board.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 7 9. Fit the supplied Edge Guards on the me tal plate all the way to their bottoms. • Please be careful not to injure y our hands while fitting the Edge Guards.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 8 12. Connect the Interface Cable to the RFID Module. 13. Secure the RFID Module to the printer with a supplied Double Sems Screw.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 9 15. Re-place the Media Sensor Block. 16. Connect the Antenna Cable to t he Antenna Ass’y until it clicks, and fasten the Antenna Cable with the Cable Clamp, as shown below.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 10 2. Insert the Shield Sheet, without the backing paper removed, under the Media Guides from behind, and slightly slide it toward the Plat en.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 11 • RFID Module Settings After installing the RFID Module on the printer, conf igure the RFID module settings using the system mode on the printer.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 12 <10>RFID TAG NONE Continued from the previous page. RFID tag type setting menu is displayed. Choose “EPC C1 Gen2: 24” with the [FEED] or [RESTART] key.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 13 Continued from the previous page. <10>RFID R CYCLE TIM 4.0 Read retry timeout setting menu is displayed. Set the timeout period during which RFID tag read retries are allow ed, with the [FEED] or [RESTA RT] key.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 14 Continued from the previous page <10>RFID A DJ RETRY +00 RFID adjustment for retry menu is displayed.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 15 Continued from the previous page. <10>RFID Q VALUE 2 [PAU SE] Q value setting menu is displayed. In the case multiple RFID tags are read at t he same time, this menu is useful to pinpoint a target tag.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 16 • AGC Threshold Setting The B-SA704-RFID-U2-EU-R choo ses a t ag to write data on acco rding to a r adio intensity of RFID tags (AGC value).
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 17 3) Set an AGC threshold of data write. Set a value which is lower than the AG C value obtained by a read test by 1 or 2, taking variation of RFID tags in performance into consideration.
INSTALLATION PROCED URE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Nov. 7, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8- 18 • Identification of The Rfid Module (B-SA704-RFID-U2-EU-R) As from.
Ein wichtiger Punkt beim Kauf des Geräts Toshiba B-SA4T (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Toshiba B-SA4T noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Toshiba B-SA4T - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Toshiba B-SA4T reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Toshiba B-SA4T erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Toshiba B-SA4T besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Toshiba B-SA4T verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Toshiba B-SA4T. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Toshiba B-SA4T gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
