Benutzeranleitung / Produktwartung 205L des Produzenten Toshiba
Zur Seite of 128
MULTIFUNCTIONAL DIGITAL SYSTEMS Troubleshooting Guide.
©2009, 2010 TOSHIBA TEC CORPORATION All rig hts reserved Under the copyright laws, this manual ca n not be reproduced in any form without prior written permission of TTEC. No patent li ab ility is assumed, however, with respect to the use of the information contained herein.
Preface 1 Preface Thank you for purchasing TOSHIBA Multifunctional Digital S ystems. This manual describes how to troubleshoot the problems that could occur whil e you are using the equipment. K eep this manual within easy reach, and use it to configure an environment that makes the best use of the e-ST UDIO’s functions.
.
CONTENTS 3 CONTENTS Preface ............ ................ ............. ................ ................ ............. ................ ............. .................... 1 Chapter 1 TROUBLESHOOT ING FOR THE HARDWARE Messages Displayed on the Touch Panel .
4 CONTENTS Cannot remember the document password for a Private Print job ................. ................ ..... 79 Printer Driver Problems ............. ................ ...... .......... ............. ................ ............. ................
CONTENTS 5 Chapter 7 CHECKING THE EQUI PMENT STATUS WITH TopAccess Hardware Status Icons on TopA ccess [Device] Tab ............... ....... ............. ................ ...... 104 Error Messages ............. ................ ................ ......
6 CONTENTS.
1. TROUBLESHOOTING FOR THE HARDW ARE This chapter describes how to troubleshoot problems with paper , toner and other finishing processes. This chapter also describes how to supply the paper , to ner and staples. Messages Displayed on the T ouch Panel .
1 TROUBLESHOOTING FOR THE HARDW ARE 8 Messages Displayed on the Touch Panel Messages Displayed on the T o uch Panel When a message appears on the touch panel, s ee the table below to solve the probl em. Message Problem Description Corrective Action Close *** cover .
1 TROUBLESHOOTING FOR THE HARDW ARE Messages Displayed on the Touch Panel 9 Examine stapler in the Saddle S titch unit S taple jam has occurred in the stapler of the saddle stitch unit.
1 TROUBLESHOOTING FOR THE HARDW ARE 10 Messages Displayed on the Tou ch Panel Error Codes The error codes indicating the status of the equipment may a ppear o n the touch panel. Y ou can find th e listings of these error codes in Chapter 7. P .1 10 “Error Codes” The number of originals exceeds the limits.
1 TROUBLESHOOTING FOR THE HARDW ARE Clearing a Paper Jam 11 Clearing a Paper Jam Locating a p aper jam The equipment stops copying when the original or copy paper is jammed. Paper jams a re notified on the touch panel as follows: The paper jam symbol helps you locate the p aper jam.
1 TROUBLESHOOTING FOR THE HARDW ARE 12 Clearing a Paper Jam Clearing a p aper jam 1 Clear the p aper jam Clear the paper jam following the guidance shown on th e touch panel. Press or to scroll the pages. 2 Af ter clearing the jam, close all the opened c overs.
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 13 1 TROUBLESHOOTING FOR THE HARDW ARE If p aper jams occur frequently The following are the common causes of paper jams. If th e problem persists, check for the following situations. y An unsuitable original is place d on the Reversing Automati c Document Feeder.
1 TROUBLESHOOTING FOR THE HARDW ARE 14 Clearing a Paper Jam 6 Lower the original feeder tray . Paper jam in the Reversing Automatic Document Feeder (optional) (Upper) 5 Raise the original feeder tray , and remove the original under the tray . 7 Close the upper cover .
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 15 1 TROUBLESHOOTING FOR THE HARDW ARE 6 Close the transport guide. 3 T urn the dial to remove the original. 4 Open the transport guide. 5 Raise the guide plate under th e transport guide, and remove the original under the guide plat e.
1 TROUBLESHOOTING FOR THE HARDW ARE 16 Clearing a Paper Jam Paper jam in the drawer feeding portion 3 Close the cover of the drawer fe eding portion. Paper jam in the Large Cap acity Feeder (optional) 1 Open the cover of the drawer feeding portion.
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 17 1 TROUBLESHOOTING FOR THE HARDW ARE 3 Close the p aper feed cover . Paper jam in the Paper Feed Ped est al (optional) 3 Close the p aper feeder cover . Paper jam in the byp ass tray 2 Remove the jammed p aper .
1 TROUBLESHOOTING FOR THE HARDW ARE 18 Clearing a Paper Jam Paper jam in the auto matic duplexing unit Be careful not to le t your fingers be caught betw een the equipment and th e duplexing unit or auto matic duplexing unit. This could injure you.
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 19 1 TROUBLESHOOTING FOR THE HARDW ARE 4 Lower the transfer unit carefully and then close the automatic duplexing unit. Paper jam on the p aper transport p ath Be careful not to le t your fingers be caught betw een the equipment and th e duplexing unit or auto matic duplexing unit.
1 TROUBLESHOOTING FOR THE HARDW ARE 20 Clearing a Paper Jam Paper jam in the fuser unit y Be careful not to let yo ur fingers be caught between the eq uipment and the duplexing unit or au tomatic duplexing un it. This could injure you. y Do not touch the fuser unit or the met al portion around it.
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 21 1 TROUBLESHOOTING FOR THE HARDW ARE Pulling it down 5 Remove p aper that sticks out from the exit tray side. 6 When a finisher (optional) is inst alled, open the Bridge Kit (optional) cover .
1 TROUBLESHOOTING FOR THE HARDW ARE 22 Clearing a Paper Jam 10 Close the automatic duplexing unit. Paper jam in the Job Sep arator an d the Offset T ray (both optional) The procedure below is only.
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 23 1 TROUBLESHOOTING FOR THE HARDW ARE 4 Close the Job Sep arator cover or the Offset T ray cover . 5 Close the automatic duplexing unit. Paper jam in the Bridge Kit (optional) 3 Close the Bridge Kit cover .
1 TROUBLESHOOTING FOR THE HARDW ARE 24 Clearing a Paper Jam When the Hole Punch Unit MJ-6101 is inst alled 2 Remove the jammed p aper . 3 Open the Bridge Kit cover . When the Hole Punch Unit MJ-6101 is installed, proceed to step 5. 4 Remove the jammed p aper .
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 25 1 TROUBLESHOOTING FOR THE HARDW ARE 8 Close the Bridge Kit cover . Jam in the lower receiving tray . 6 Remove the jammed p aper by turning the knob. 7 Close the Hole Punch Unit c over . 9 Close the upper receiving tray of t he finisher .
1 TROUBLESHOOTING FOR THE HARDW ARE 26 Clearing a Paper Jam 2 Remove the jammed p aper . 3 Lower the shutter of the p aper exit portion to open it. 4 Remove the jammed p aper . 5 Open the Bridge Kit cover . When the Hole Punch Unit MJ-6101 is installed, proceed to step 7.
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 27 1 TROUBLESHOOTING FOR THE HARDW ARE When the Hole Punch Unit MJ-6101 is inst alled 10 Close the Bridge Kit cover . 7 Open the Hole Punch Unit cover . 8 Remove the jammed p aper by turning the knob.
1 TROUBLESHOOTING FOR THE HARDW ARE 28 Clearing a Paper Jam Paper jam in the Saddle Stitch Finisher MJ-1024 and the Hole Punch Unit MJ-6004 (both optional) When the Hole Punch Unit MJ-6004 is inst alled 1 Hold up the guide of the p aper exit portion and remove the jammed p aper .
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 29 1 TROUBLESHOOTING FOR THE HARDW ARE 5 Return the Hole Punch Unit to it s original position, and close the front cover . 8 Close the upper cover of the finis her . 6 Raise the lever , and open the upper cover of the finisher until it is locked.
1 TROUBLESHOOTING FOR THE HARDW ARE 30 Clearing a Paper Jam Paper jam in the saddle stitch unit of the Saddle Stitch Finisher MJ-1024 (optional) 1 Open the front cover of the finisher . 2 Slide the green handle toward the right, and remov e the jammed p aper .
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 31 1 TROUBLESHOOTING FOR THE HARDW ARE 10 Close the p aper exit cover of the saddle stitch unit and the front cover of the finisher . 6 T urn the left k nob clockwise while pressing it. 7 Remove the jammed p aper from the exit portion of the saddle stitch unit.
1 TROUBLESHOOTING FOR THE HARDW ARE 32 Clearing a Paper Jam Paper jam in the Saddle S tit ch Finisher MJ-1025 (optional) 4 Close the upper cover of the finis her . 1 Remove the jammed p aper from the p aper exit portion. 2 Open the upper cover of the finishe r .
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 33 1 TROUBLESHOOTING FOR THE HARDW ARE Paper jam in the Hole Punc h Unit of the Saddle Stitch Finisher MJ-1025 (optional) Be careful not to let your fingers be caught between the equ ipment and the finisher (optio nal) .
1 TROUBLESHOOTING FOR THE HARDW ARE 34 Clearing a Paper Jam Paper jam in the st apler unit of the Sa ddle Stitch Finisher MJ-1025 (optional) 3 Close the front cover of t he finisher . 1 Open the front cover of the finisher . 2 T urn the green knob at the center clockwise until the inside of the window above the knob turns blue.
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 35 1 TROUBLESHOOTING FOR THE HARDW ARE Paper jam in the saddle stitch unit of the Saddle Stitch Finisher MJ-1025 (optional) Be careful not to let your fingers be caught between the equ ipment and the finisher (optio nal) .
1 TROUBLESHOOTING FOR THE HARDW ARE 36 Clearing a Paper Jam 6 Close the jam access cover and th e front cover of the finisher . 5 T urn the green knob on the lower right side clockwise and then remove the p aper jammed at the exit section of the saddle stitch unit.
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 37 1 TROUBLESHOOTING FOR THE HARDW ARE Paper jam in the Hanging Fi nisher MJ-1031 (optional) Be careful not to let your fingers be caught between the equ ipment and the finisher (optio nal) .
1 TROUBLESHOOTING FOR THE HARDW ARE 38 Clearing a Paper Jam Clearing p aper jams caused by a wrong paper size setting Paper jams occur when there is a mismatch between the size of the paper in a drawer or the bypass tray and the size registered for the corresponding drawer or the bypass tray in the equipment.
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 39 1 TROUBLESHOOTING FOR THE HARDW ARE 2 Remove the jammed p aper . 5 Press the [USER] t ab to enter the [USER] menu and press [DRA WER]. 6 Press the drawer button indicated in the messa ge. 3 Press the [POWER] button on the control p anel.
1 TROUBLESHOOTING FOR THE HARDW ARE 40 Clearing a Paper Jam 7 Press the p aper size button for the p aper that is set in the drawer . 8 Press the [USER FUNCTIONS] button to return to the b asic menu and try copying or printing again. Jam when making copies or pr ints (using the byp ass tray) 2 Remove the jammed p aper .
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Paper Jam 41 1 TROUBLESHOOTING FOR THE HARDW ARE Jam when printing from the F AX 2 Remove the jammed p aper . 5 Check the p aper size registered to the drawer indicated in the message by means of the drawer button on the touch p anel.
1 TROUBLESHOOTING FOR THE HARDW ARE 42 Clearing a Paper Jam 6 Place the p aper in the drawer indicated in the message. Be sure to place the same- sized p aper as the size you check ed in step 5.
1 TROUBLESHOOTING FOR THE HARDW ARE Clearing a Staple Jam 43 Clearing a St ap le Jam When a staple jam has occurred in the stapler of the finisher or sadd le stitch unit, clear the jam fo llowing the procedure below . P .43 “St aple jam in a finisher” P .
1 TROUBLESHOOTING FOR THE HARDW ARE 44 Clearing a Staple Jam 7 Close the front cover of t he finisher . Saddle Stitch Finisher MJ-1024 5 Holding the knob, raise the guide, and return it to it s original position. 6 Fit the st aple cartridge into the st apler .
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Staple Jam 45 1 TROUBLESHOOTING FOR THE HARDW ARE 7 Close the front cover of t he finisher . 3 Lower the guide while holding the knob. A: S tapling area Do not touch the stapling area. The actual need le point could cause you personal inju ry .
1 TROUBLESHOOTING FOR THE HARDW ARE 46 Clearing a Staple Jam Saddle Stitch Finisher MJ-1025 1 Open the front cover of the finisher . 2 Pull out the st apler unit holding the green handle.
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Staple Jam 47 1 TROUBLESHOOTING FOR THE HARDW ARE 10 Close the front cover of t he finisher . 6 Remove the jammed st aples. 7 Holding the knob, lower the guide, a nd return it to it s original position. 8 Fit the st aple cartridge on the st apler .
1 TROUBLESHOOTING FOR THE HARDW ARE 48 Clearing a Staple Jam Hanging Finisher MJ-1031 Be careful not to let your fingers be caught between the equ ipment and the finisher (optio nal). This could injure you. 1 Sep arate the finisher from the equipment.
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Staple Jam 49 1 TROUBLESHOOTING FOR THE HARDW ARE 5 Remove the jammed st aples. 6 Holding the knob, raise the guide, and return it to it s original position. 7 Fit the st aple cartridge on the st apler .
1 TROUBLESHOOTING FOR THE HARDW ARE 50 Clearing a Staple Jam S taple jam in the saddle stitch unit When staples are jammed in the saddle stitch unit of the Saddle S titch Finisher MJ-1024, fol low the procedure below to clear the jam. 1 Open the front cover of the finisher .
1.TROUBLESHOOTING FOR TH E HARDW ARE Clearing a Staple Jam 51 1 TROUBLESHOOTING FOR THE HARDW ARE 11 Make sure of the following two requirement s before test st apling: y The finisher is securely attached to the equipment. y A3, B4, A4-R, LD, or L T -R paper is set in the drawer .
1 TROUBLESHOOTING FOR THE HARDW ARE 52 Clearing a Staple Jam 12 Close the front cover of t he finisher . T est stapling starts automatically . T e st stapling is necessary to prevent vo id st apling. Note that the test stapling starts automatically when the two requirements in step 1 1 are met with the front cover of th e finisher closed .
1 TROUBLESHOOTING FOR THE HARDW ARE Replacing a Toner Cartr idge 53 Replacing a T oner Cartridge When the toner cartridge run s out, the message “Install New toner cartridge” appears. Replace th e toner cartridge following the procedure below when you see this message.
1 TROUBLESHOOTING FOR THE HARDW ARE 54 Replacing a Toner Cartridge Never attempt to incine rate toner cartridges. Dispose of used toner cartridges in accordance with local re gulations. Some toner remains in the to ner cartridge while the message “T oner near Empty” is displayed.
1.TROUBLESHOOTING FOR TH E HARDW ARE Replacing a Toner Cartr idge 55 1 TROUBLESHOOTING FOR THE HARDW ARE 3 Pull out the toner cartridge. Never attempt to incine rate toner cartrid ges. Dispose of used toner cartridges in accordance with local regulations.
1 TROUBLESHOOTING FOR THE HARDW ARE 56 Replacing a Toner Cartridge 9 Close the front cover . 8 Clean the charger . Hold the cleaning knob of the charger and pull it out toward you carefully until it comes to a stop. Then reinsert it in its original position carefully .
1.TROUBLESHOOTING FOR TH E HARDW ARE Replacing a Toner Cartr idge 57 1 TROUBLESHOOTING FOR THE HARDW ARE Replacing a “Near Empty” toner cartridge The message “T oner near Empty” appears on th e touch panel w hen there is not much toner left in a toner ca rtridge.
1 TROUBLESHOOTING FOR THE HARDW ARE 58 Replacing a Toner Cartridge 3 Press [REPLACE TONER CARTRIDGE]. 4 T o replace a toner cartridge, press [YES]. T o cancel, press [NO]. 5 Replace the toner cartridg e. See P .53 “Replacing a T oner Cartri dge” for the correct procedure.
1 TROUBLESHOOTING FOR THE HARDW ARE Refilling With Staples 59 Refilling With S t aples Refill with staples accordin g to the following p rocedures when th e staples in the stapler of the finisher and saddle stitch unit run out. P .59 “Re filling finisher staples” P .
1 TROUBLESHOOTING FOR THE HARDW ARE 60 Refilling With Staples 6 Close the front cover of t he finisher . If the message “Check staple cart ridge” remains, repeat the proc edu re above from steps 1 to 6. Saddle Stitch Finisher MJ-1024 5 Fit the st aple cartridge into the st apler .
1.TROUBLESHOOTING FOR TH E HARDW ARE Refilling With Staples 61 1 TROUBLESHOOTING FOR THE HARDW ARE 8 Close the front cover of t he finisher . If the message “Check staple cart ridge” remains, repeat the proc edu re above from steps 1 to 8. 4 Af ter the transp arent cover is lif ted, t ake out the empty st aple case.
1 TROUBLESHOOTING FOR THE HARDW ARE 62 Refilling With Staples Saddle Stitch Finisher MJ-1025 1 Open the front cover of the finisher . 2 Pull out the st apler unit holding the green handle.
1.TROUBLESHOOTING FOR TH E HARDW ARE Refilling With Staples 63 1 TROUBLESHOOTING FOR THE HARDW ARE 6 Af ter the transp arent cover is lif ted, remove the empty st aple case. 7 Fit the new st aple case into the st aple cartridge. Push the staple case into th e cartridge unt il it clicks.
1 TROUBLESHOOTING FOR THE HARDW ARE 64 Refilling With Staples 11 Close the front cover of t he finisher . If the message “Check staple cartri dge” remains, repeat the procedu re above from steps 1 to 1 1. Hanging Finisher MJ-1031 Be careful not to let your fingers be caught between the equ ipment and the finisher (optio nal).
1.TROUBLESHOOTING FOR TH E HARDW ARE Refilling With Staples 65 1 TROUBLESHOOTING FOR THE HARDW ARE 4 Press the buttons on both sides of the cartridge. The transparent cover of the cartridge is lifted. 5 Af ter the transp arent cover is lif ted, remove the empty st aple case.
1 TROUBLESHOOTING FOR THE HARDW ARE 66 Refilling With Staples If the message “Check staple cartri dge” remains, repeat the procedu re above from steps 1 to 10. Refilling saddle stitch unit st aples When the staples of the stapler in the Saddle Stitch Finisher MJ-1024 have run out, refill staples following the procedure below .
1.TROUBLESHOOTING FOR TH E HARDW ARE Refilling With Staples 67 1 TROUBLESHOOTING FOR THE HARDW ARE 3 Unlock the st apler of the saddle stitch unit by pulling it s handle toward you. Keep pulling the handle, an d turn the st apler clockwise by about 60 degrees.
1 TROUBLESHOOTING FOR THE HARDW ARE 68 Refilling With Staples 8 Make sure that the following two requirement s are met before test st apling: y The finisher is securely attached on the equipment.
1 TROUBLESHOOTING FOR THE HARDW ARE Cleaning the Charger 69 Cleaning the Charger If the inside of the charger is dirty , staining may appear on the copi ed image. Clean the charger following the procedure below . 3 Close the front cover . 1 Open the front cover .
1 TROUBLESHOOTING FOR THE HARDW ARE 70 Cleaning the Hole Punch Dust Bin Cleaning the Hole Punch Dust Bin When the hole punch dust bin becomes full, dispose of the paper punchings following the procedure be low . Hole Punch Unit MJ-6101 / MJ-6004 3 Dispose of the p aper punchings.
1.TROUBLESHOOTING FOR TH E HARDW ARE Cleaning the H ole Punch Du st Bin 71 1 TROUBLESHOOTING FOR THE HARDW ARE 3 Dispose of the p aper punchings. 4 Push back in the hole punch dust bin. 5 Connect the finisher to the equi pment. Move the finisher slowly toward the equipment, placing both of your hands on the front and the back of the finisher .
1 TROUBLESHOOTING FOR THE HARDW ARE 72 Removal and Installation of the Exit Support Tr ay Removal and Inst al lation of the Exit Support T ray If a large number of sheets is printed at a time, so me print ed sheets may be pushed out of t he exit tray .
2. TROUBLESHOOTING FOR COPYING This chapter describes how to troubleshoot the prob lems on copying and copy output. Copying Problems...................
2 TROUBLESHOOTING FOR COPYING 74 Copying Problems Copying Problems See the table below when you have a problem in operatin g copy functio n or have an un expected copy output. Problem Desc ription Cause Corrective Ac tion Functions cannot be set. Another function that is unavailable for the combination has already been set.
2.TROUBLESHOOTING FOR COPYING Copying Problems 75 2 TROUBLESHOOTING FOR COPYING Copied image has unevenness in the horizontal direction. The charger is stained. Clean the charger . P .69 “Cleaning the Charger” Copied image has black streaks in the horizontal direction.
.
3. TROUBLESHOOTING FOR PRINTING This chapter describes how to troubleshoot the problems on printing. Print Job Problems ......................................... ................................................................ .... ... 78 Clearing print job errors .
3 TROUBLESHOOTING FO R PRINTING 78 Print Job Problems Print Job Problems This section describes how to clear the print jobs errors. Clearing print job errors Problem Description A print job error occurs and [JOB ST A TUS] blinks when the paper specified by the computer is not set in the drawers of the equipment.
3.TROUBLESHOOTING FOR PRINTING Print Job Problems 79 3 TROUBLESHOOTING FOR PRINTING Cannot remember the document p assword for a Private Print job Problem Description I cannot remember the document password for my Private Print job.
3 TROUBLESHOOTING FO R PRINTING 80 Printer Driver Problems Printer Driver Problems This section describes the troubleshooting for the printer drivers. For the error messages that ap pear during the installation of the printer dr ivers, refer to the Software Installation Guide .
3.TROUBLESHOOTING FOR PRINTING Printer Driver Problems 81 3 TROUBLESHOOTING FOR PRINTING Retrieval of printer configuration failed Problem Description When accessing the printer properties, th e message “Retri eval o f printer configuration fai led” is displayed.
3 TROUBLESHOOTING FO R PRINTING 82 Network Connection Problems Network Connection Problems This section describes the troubleshooting for p rinting in the network co nnection environment. See also the checklists by types of printing and operating systems on P .
3 TROUBLESHOOTING FOR PRINTING Client Problems 83 Client Problems This section describes how to i dentify and correct the prob lems cause d by the clients* connected to the equipment. * One of the common examp les of clients is a compute r that sends a print job to the equip ment and make it perform prin ting.
3 TROUBLESHOOTING FO R PRINTING 84 Hardware Problems Hardware Problems This section describes troubles caused by the hardware device (the equipment). If an icon or a message indicating an error is not.
4. TROUBLESHOOTING FOR SCANNING This chapter describes how to troubleshoot the problems of scanning . Scanning Problems .......... .......................................................................... .......................... .. 86 Cannot E-mail my scans .
4 TROUBLESHOOTING FOR SCANNING 86 Scanning Problems Scanning Problems This section describes troubleshooting for using scan data. Cannot E-mail my scans Problem Description I have scanned a document a nd sent the copy a s an e-mail attachment, but the e-mail does not reach the s pecified e -mail address.
5. TROUBLESHOOTING FOR e-Filing This chapter describes how to troubleshoot the problems on e-Filing . e-Filing We b Utility Problems .................................................................... ............................ 88 e-Filing Web Utility terminates the se ssion .
5 TROUBLESHOOTING FOR e-Filing 88 e-Filing Web Utility Problems e-Filing We b Utility Problems This section describe s troubleshooti ng for the web browser-based e-Fili ng web utility . Y ou will also find the error messages and the corrective actions for each message.
5.TROUBLESHOOTING FOR e-Filing e-Filing Web Utility Problems 89 5 TROUBLESHOOTING FOR e-Filing Error messages See the table below to troubleshoot the problem if a message ap pears. Message Corrective Action Internal error occurred. Please restart e-Filing.
5 TROUBLESHOOTING FOR e-Filing 90 e-Filing Web Utility Problems The document is being used. Please try again later. The se lected document is being used by anoth er user . Try again after the other user has finished using the document. File format doesn’t correspond.
6. TROUBLESHOOTING FOR NETWORK CONNECTIONS This chapter describes how to troubleshoo t the problems on network conn ections. Locating the Equipment in the Network............................. .................................................. 92 Cannot locate the equipment in the network .
6 TROUBLESHOOTING FOR NETWORK CONNECT IONS 92 Locating the Equipment in the Network Locating the Equipment in the Network Cannot locate the equipment in the network Problem Description I cannot locate the equipment in the network. Corrective Action Improper settings may cause the problem s in locating the equipment in the netwo rk.
6.TROUBLESHOOTING FOR NETWORK C ONNECTIONS Locating the Equipment in the Netwo rk 93 6 TROUBLESHOOTING FOR NETWORK CONNECTIONS Cannot locate the equipme nt with Local Discovery Problem Description Local Discovery cannot detect the equipment. Corrective Action The equipment is normally loca ted autom atical ly by SNMP .
6 TROUBLESHOOTING FOR NETWORK CONNECT IONS 94 Locating the Equipment in the Network Equipment does not re spond to ping command Problem Description The equipment does not respo nd to a ping command. Corrective Action Check the network settings follo wing the checklist below .
6 TROUBLESHOOTING FOR NETWORK CONNECTIONS LDAP Search and Authentication Problems 95 LDAP Search and Authentication Problems Network shut down occurs or touch p anel disabled af ter LDAP search Problem Description After performing the LDAP search, the network s hutdown occurs or the touch p anel is disabled .
6 TROUBLESHOOTING FOR NETWORK CONNECT IONS 96 Printing Problems (Network Related) Printing Problems (Network Related) Among the several ways to use the equipment in the network, th e simplest one is to set the equ ipment in the TCP/IP environment using a DHCP server to assign IP addresse s dynamically to devices.
6.TROUBLESHOOTING FOR NETWORK C ONNECTIONS Printing Prob lems (Net work Related) 97 6 TROUBLESHOOTING FOR NETWORK CONNECTIONS IPP print in a Windows operating system environment Novell print in a NetW are environment No.
6 TROUBLESHOOTING FOR NETWORK CONNECT IONS 98 Printing Problems (Network Related) Macintosh environment UNIX/Linux environment No. Check... Y es No Corrective Action 1 Is AppleT alk enabled on the equipment? Next S tep Ø Ö Enable AppleT alk.
6 TROUBLESHOOTING FOR NETWORK CONNECTIONS Network Fax (N/W-Fax) Driver Proble ms 99 Network Fax (N/W -Fax) Driver Problems This section describes the troubleshooting for the Network Fax (N/W-Fax) driver .
6 TROUBLESHOOTING FOR NETWORK CONNECT IONS 100 Networ k Fax (N/W-Fax) Driver Problems Location does not c ont ain information about your hardware Problem description The path to the *.inf file selected during driver installation is too far away . In other words, ther e are too many characters i n the directory path.
6.TROUBLESHOOTING FOR NETWORK C ONNECTIONS Network Fa x (N/W-Fa x) Driver Prob lems 101 6 TROUBLESHOOTING FOR NETWORK CONNECTIONS Fax transmission cannot be pe rformed with a cover sheet Problem d.
.
7. CHECKING THE EQUIPMENT ST A TUS WITH T opAccess This chapter describes how to check the status of the equipment with T opAccess. Hardware St atus Icons on T opAccess [Device] T ab .................................................... ..... 104 Error Messages .
7 CHECKING THE EQUIPMENT ST A TUS WITH T o pAccess 104 Hardware Status Icons on TopAccess [Device] Tab Hardware St atus Icons on T opAccess [Device] T ab When the equipment requires maintena nce or wh.
7.CHECKING THE EQUIPMENT ST A TUS WITH T opAccess Hardware Status Icons on TopA ccess [Device] Tab 105 7 CHECKING THE EQUIPMENT ST A TUS WITH T opAccess Paper Empty This icon indicates no paper is left in a drawer . Refer to the Copying Guide . Paper Jam This icon indicates a paper jam occurred.
7 CHECKING THE EQUIPMENT ST A TUS WITH T o pAccess 106 Error Messages Error Messages When a message appears on the [Device] T ab of T opAccess, see the table below for the co rrective actio n. T opAccess Message Corrective Action Front Cover Open - Please Close Cover .
7 CHECKING THE EQUIPMENT ST A TUS WITH T opAccess Error Messag es 107 Expired scan documents deleted from share folder . Expired documents are deleted automatically from the “SCAN” folder in the “SHARE_FILE” folder . Expired Sent Fax documents deleted from share folder .
7 CHECKING THE EQUIPMENT ST A TUS WITH T o pAccess 108 Error Messages Active Directory Domain - V erification of the Ticket has failed V e rify the user name and password and try again.
7 CHECKING THE EQUIPMENT ST A TUS WITH T opAccess Error Messag es 109 Encapsulation mode mismatch Check the IPse c mode (Transport/T unnel) in MFP and peer . Peer IP Address mismatch Remote T r affic sele ctor mismatch. Check t he destination address/ port in IPsec filter .
7 CHECKING THE EQUIPMENT ST A TUS WITH T o pAccess 110 Error Codes Error Codes T opAccess has the pages for the job lists; print, transmission, reception, and scan jobs. The fol lowing error codes are shown on these pages in the [Logs] tab (successful jobs ha ve no codes).
7 CHECKING THE EQUIPMENT ST A TUS WITH T opAccess Error Codes 111 A2A1 Limit over error (Color) The number of prints has exceeded the one specified for the user code, or users (guests) are not authorized to perform color printing . Clear the limit counter , or authorize users so t hat they can perform color printing.
7 CHECKING THE EQUIPMENT ST A TUS WITH T o pAccess 112 Error Codes Error codes on transm ission and reception Error Code Problem Desc ription Corrective Acti on 001 1 Paper jam Clear the jammed printing paper . 0012 Original jam Clear the jammed original.
7.CHECKING THE EQUIPMENT ST A TUS WITH T opAccess Error Codes 113 7 CHECKING THE EQUIPMENT ST A TUS WITH T opAccess 1C69 SMTP server connection error Ask your administrator to set the login name or password of the SMTP server and perform the job again.
7 CHECKING THE EQUIPMENT ST A TUS WITH T o pAccess 114 Error Codes 3C60-3C62 Offramp security error Confirm that the specified fax numbers are registered in the address book of the equipment. If not, register the fax number s in the address book and ask the sender to resend the Email with the correct fax numbers.
7.CHECKING THE EQUIPMENT ST A TUS WITH T opAccess Error Codes 115 7 CHECKING THE EQUIPMENT ST A TUS WITH T opAccess Error codes on scan jobs The error indications on scan jobs are done as follows: y On T opAccess log list, messages indi cating the status are displayed.
7 CHECKING THE EQUIPMENT ST A TUS WITH T o pAccess 116 Error Codes 2C71 SMTP authentication error Confirm that the login name and password are correct. If SSL is enabled, make sure that the SSL port number is correctly set. 2C72 POP Before SMTP error Confirm that the POP Before SMTP settings and POP3 settings are correct.
7.CHECKING THE EQUIPMENT ST A TUS WITH T opAccess Error Codes 117 7 CHECKING THE EQUIPMENT ST A TUS WITH T opAccess 2D62 Failed to connect to network destination. Check destination path. Make sure that the network folder is shared in your network and retry the scan.
7 CHECKING THE EQUIPMENT ST A TUS WITH T o pAccess 118 Error Codes 2B90 Insufficient Memory . T urn the pow er OFF and then back ON. Retry the scan. If the error still occurs , contact your service representative.
8. WHEN SOMETHING IS WRONG WITH THE EQUIPMENT T ry the tro ubleshooting ti ps in this chapter when you think there is something wrong with the equipment. This chapter al so describes the daily care for the eq uipment. When Y ou Think Something Is Wr ong With the Equipment .
8 WHEN SOMETHING IS WRONG WITH THE EQUIPMENT 120 When You Think Something Is Wrong With the Equipment When Y ou Think Something Is W rong With the Equipment If you think there is something wrong wit h the equipment, check the following items.
8.WHEN SOMETHING IS WRONG WITH THE EQUIPMENT When You Think Something Is Wrong With th e Equipment 121 8 WHEN SOMETHING IS WRONG WITH THE EQUIPMENT Originals and p aper Problem Desc ription Cause Corrective Ac tion The original is jammed. The original is unavailable on the equipment.
8 WHEN SOMETHING IS WRONG WITH THE EQUIPMENT 122 Regular Maintenance Regular Maintenanc e We recommend that you clean the following portions weekly so that the originals can always be scanned in unsoiled conditions. y Be careful not to scratch the portions when cleaning th em.
INDEX 123 INDEX A AppleTalk print ... ............. ................ ............. .............82 C Cleaning charger ....... ............. ................ ............. ................. 69 hole punch dust bin ............. ............. ...........
124 INDEX SMB print ........... ................ ................ ............. ... 82 , 96 Staple jam - clearing Finisher MJ-1101 .......... ............ ................. ............. 43 Hanging Finisher MJ-1031 ...... ................ ............
DP-2090/2520/3000/3570/4570 OME080178B0.
2-17-2, HIGASHIGOT ANDA, SHINAGA WA-KU, TOKYO, 141-8664, JAP AN MUL TIFUNCTIONAL DIGIT AL S YSTEMS T roubleshooting Guide ©2009, 2010 TOSHIBA TEC CORPORATION All rig hts reserved R081120G8702-TTEC Ve.
Ein wichtiger Punkt beim Kauf des Geräts Toshiba 205L (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Toshiba 205L noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Toshiba 205L - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Toshiba 205L reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Toshiba 205L erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Toshiba 205L besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Toshiba 205L verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Toshiba 205L. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Toshiba 205L gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
